First Time Use; Quick Install Menu; Primary Connections; Continuous Recording - Bosch 670 Series Quick Install Manual

Video Recorder 670 Series
Quick install
To get the unit quickly operational, make the connections
described below and then enter the relevant data in the Quick
install menu. The Quick install menu appears the first time the
unit is started.
Connections

Primary connections

1. Connect the cameras to the VIDEO IN BNC connectors
(automatically terminated).
2. Connect monitor A to the VGA MON A output supporting
800x600 (4:3), 1024x768 (4:3), or 1280x1024 (5:4),
1366x768 (16:9) and 1440x900 (16:10).
3. Connect USB mouse to a USB port.

Optional connections

1. Connect monitor B to the HDMI (or CVBS) MON B
connector (supporting 800x600).
2. Connect up to 4 audio signals to the AUDIO IN RCA
(CINCH) inputs.
3. Connect 2 AUDIO OUT RCA (CINCH) outputs to the
monitor or an audio amplifier.
4. Connect up to 8/16 ALARM IN inputs (via the supplied
terminal blocks).
5. Connect up to 4 ALARM OUT outputs (via the supplied
terminal blocks).
6. Connect a pan/tilt/zoom control unit to the RS-485 or
RS-232 port.
7. Connect to your network via the Ethernet port.
8. Connect a Bosch Intuikey keyboard cable to the
Keyboard-IN port if required.
Powering up
Switch on all connected equipment.
– Connect the power unit to the AC power outlet.
– Connect the DC power cord to the 12VDC connector on
the unit.
First-time use
The Quick install menu opens the first time the unit is used. Fill
in the basic settings in the three tabs to get the unit
operational. The unit begins recording automatically when the
Quick install menu is closed.
Bosch Security Systems
Navigating
Use the supplied USB mouse. Alternatively, use the following
front panel keys:
– Use the enter key to select a submenu or item.
– Use the arrow
move through a menu or list.
– Use the exit key to go back or to switch off the
menu.
After bootup, the unit presents the log in screen over a quad
display. The default User ID is ADMINISTRATOR, the default
password is 000000 (six zeros).

Switching monitors

To switch the monitor A output to the HDMI connector:
1. Remove power from the DVR.
2. Press and hold the multiscreen
panel.
3. Supply power to the unit.
– The unit starts with monitor A on the HDMI
connector and monitor B on the VGA connector.
To switch the monitor A output to the VGA connector:
1. Remove power from the DVR.
2. Press and hold the quad key on the front panel.
3. Supply power to the unit.
– The unit starts with monitor A on the VGA
connector and monitor B on the HDMI connector.

Quick install menu

The Quick install menu contains three tabs: International,
Continuous Recording, and Network. Click the Exit button to
exit the Quick install menu. Changing Quick install settings
overwrites customized settings.
International
Language Select the language for the menu from the list.
Time zone Select a time zone from the list.
Time
format
Time
Date
keys to
format
Date

Continuous Recording

Set the Continuous Recording Resolution, Quality, Frame rate,
Covert, and Audio for each profile in the table.
Network
DVR ID
key on the front
DHCP
IP address,
Subnet mask,
and Gateway
Quick install
Select either a 12 or a 24 hour clock format.
Fill in the current time.
Select from three date formats which show
either the month (MM), the day (DD), or the
year (YYYY) first.
Fill in the current date.
Enter a unique DVR name to be used in the
network.
Enable DHCP to have IP address, subnet
mask, and default gateway assigned
automatically by the network server.
The actual values are displayed.
Fill in the IP, subnet mask, gateway
addresses, and DNS server addresses when
DHCP is not enabled.
v2.0 | 2012.03