MrCool RG51M5/(C)EU User Manual

OPERATING THE REMOTE REMOTE CONTROL SPECS REMOTE BUTTONS FEATURE BREAKDOWN NOTICE
Please read this manual carefully before operation and keep it for future reference.
6. TIMER DISPLAY Indicator: This display area shows the settings of the TIMER. That is, if 1. Be sure there are no obstacles between the remote controller and the receiver of indoor TIMER Operation AUTOMATIC OPERATION
1. TEMP Button : Push this button to decrease the indoor temperature setting in 1°F 12. TIMER OFF Button: Press this button to initiate the auto-off time sequence. Each press
Model
Switch on the power and the OPERATION indication lamp on the display panel of the Push TIMER ON button to set the auto-on time and TIMER OFF button to set the auto-off only the starting time of operation is set, it will display the TIMER ON. If only the turning off unit otherwise the air conditioner will not work.
increments to 62°F. will increase the auto-timed setting in 30 minutes increments. When the setting time
Rated Voltage
time. 2. Keep the Remote Controller away from any liquids. time of operation is set, it will display the TIMER OFF. If both operations are set, it will show indoor unit starts flashing, and turns off after flashes for 6 times.
2. TEMP Button : Push this button to increase the indoor temperature setting in 1°F displays 10h, each press will increase the auto-timed setting 60 minutes increments. To
3. Protect the remote controller from the high temperatures and exposure to radiation. 1. Use the MODE button to select AUTO. 1. To set the starting time. TIMER ON-OFF which indicates you have chosen to set both the starting time and off time.
increments to 86°F. cancel the auto-timed program, simply adjust the auto-off time to 0.0
Transmission Distance
7. FAN SPEED Indicator: Press the FAN SPEED button to select the desired fan speed 2. Push the TEMP button to set the desired temperature within a range of 62°F ~ 86°F. 4. Keep the indoor receiver out of direct sunlight or the Air Conditioner may malfunction. 1.1 Push the TIMER ON button, then the remote controller shows TIMER ON , the last set
13. LOCK Button: When you press the recessed LOCK button, all current settings are locked Note: Press and hold and buttons together for 3 seconds will alternate the
Remote Control Manual
5. Keep Remote Controller away from EMI(Electro-Magnetic Interference) supplied by other 3. Push the ON/OFF button to start the air conditioner. The OPERATION lamp on the setting (Auto-Low-Med-High). You selection will be displayed in the LCD window except the time for the starting operation and the signal "h" will be shown on the DIGITAL DISPLAY
in and the remote controller does not accept any operation except that of the LOCK. Press temperature display between the °C & °F scale.
Environment
display panel of the indoor unit lights. The FAN SPEED is automatically set and there are no Auto fan speed. household appliances. area. You are now ready to reset the time to START the operation.
3. MODE Selection Button: Each time the button is pressed, the operation mode is shifted again to cancel the LOCK mode.
1.2 Push the TIMER ON button again to set desired unit start time. fan speed indicators shown on the display panel of the remote controller. NOTE: All signs shown in the Fig.2 is for the purpose of clear presentation. But during the actual
14. TURBO Button: Active/Disable Turbo function. Turbo function enables the unit to reach in the direction of the arrow:
PERFORMANCE FEATURES
NOTE: 4. Push the ON/OFF button again to stop the unit operation. 1.3 After setting the TIMER ON ,there will be a one-half second delay before the remote operation only the relative functional signs are shown on the display panel.
the preset temperature at cooling or heating operation in the shortest time(if the indoor
AUTO
The device could comply with the local national regulations. In Canada, it should comply with controller transmits the signal to the air conditioner. Then, after approximately another 2
unit has no this function, there is no corresponding operation happened when press
CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the FCC Rules. NOTE: 1. Operating Mode: AUTO COOL DRY HEAT(Cooling only model without) and FAN. seconds, the signal "h" disappears and the set temperature will re-appear on the digital
Turbo button.) Note: Please do not select HEAT mode if the machine you purchased is cooling only
1. In the AUTO mode, the air conditioner can logically choose the mode of COOL, FAN and HEAT Operation is subject to the following two conditions: display.
15. LED DISPLAY Button: Press this button to clear the digit display in the air conditioner, type. Heat mode is not supported by the cooling only appliance.
2. Timer Setting Function in 24 hours.
2. To set the stopping time. by sensing the difference between the actual ambient room temperature and the set (1) This device may not cause harmful interference, and
4. SWING Button: Push this switch button to activate auto swing feature of the horizontal press it again to illuminate (Not available for the units without LED display window). Install/Replace Batteries
3. Indoor Setting Temperature Range: 62°F~86°F.
2.3 After setting the TIMER OFF ,there will be a one-half second delay before the remote (2) this device must accept any interference received, including interference that may cause temperature on the remote controller.
The Remote Controller uses two alkaline dry batteries(LR03X2). louver. Push it again to stop.
4. Full function of LCD (Liquid Crystal Display)
Advantage Series
2. If the AUTO mode is not comfortable for you, the desired mode can be selected manually. controller transmits the signal to the air conditioner. Then, after approximately another 2 undesired operation.
5. FP Button: During the heating operation(only when the setting mode is HEAT), press this
1. To install the batteries, slide the back cover of the battery compartment and install the
DISPLAY SCREEN BREAKDOWN
seconds, the signal "h" disappears and the set temperature will re-appear on the digital
button and the unit will operate at high fan speed with the temperature automatically set
batteries according the direction (+and -)shown on the Remote Controller.
REMOTE BUTTONS FEATURE BREAKDOWN
COOL/ HEAT (Cooling only model without) and FAN Operation
This equipment has been tested and found to comply with the limits for a Class B digital device, display.
to 8°C/46°F. The display window of indoor unit will display "FP". Press the buttons of
2. To replace the old batteries, use the same method as mentioned above.
1. If the AUTO mode is not comfortable, you may manually over-ride the settings by using pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 2.2 Push the TIMER OFF button again to set the time you want to stop the operation.
ON/OFF, MODE, FAN SPEED, TEMP UP/DOWN, TIMER ON/OFF, SLEEP or FP while operating
against harmful interference in a residential installation. This equipment generates, uses and COOL, HEAT or FAN modes. 2.1 Push the TIMER OFF button and the remote controller will show TIMER OFF, the last set
will cancel the FP function.
Note:
can radiate radio frequency energy and, if not installed and used in accordance with the 2. Push the TEMP button to set the desired temperature within a range of 62°F ~ 86°F. time for the stopping operation and the signal "h" will be shown on the DIGITAL DISPLAY
6. AIR DIRECTION Button: Used to change the louver movement and set the desired
1. When replacing batteries, do not use old batteries or a different type battery. This may cause
instructions, may cause harmful interference to radio communications. However, there is no 3. Push the FAN SPEED to select the FAN mode of AUTO, HIGH, MED, or LOW. area. You are now ready to reset the time of the STOP operation.
up/down air flow direction. The louver changes 6° in angle for each press.
the remote control to malfunction.
Advantage Series
3. Set the starting & stopping time guarantee that interference will not occur in a particular installation. If this equipment does 4. Push the ON/OFF button, the operation lamp lights and the air conditioner start to
7. RESET Button: When you press the recessed RESET button, all current settings are
2. If you do not use the remote controller for several weeks remove the batteries. Otherwise
cause harmful interference to radio or television reception, which can be determined by turning operate as your settings. Push the ON/OFF button again to stop this unit operation. 3.1 Push the TIMER ON button, the remote controller will show TIMER ON, the last set time
cancelled and the control will return to the initial settings.
battery leakage may damage the remote controller.
the equipment off and on, the user is encouraged to try to correct the interference by one or for START operation and the signal "h" will be shown on the DIGITAL display area. You are
8. FAN SPEED Button: Used to select the Fan Speed in four steps: AUTO, LOW, MED, or
3. The average battery life under normal use is about 6 months.
more of the following measures: Note: The FAN mode can not be used to control the temperature. While in this mode, only now ready to readjust the TIMER ON to start the operation.
4. Replace the batteries when there is no answering beep from the indoor unit or if the HIGH. Each time the button is pressed, the fan speed mode is shifted.
•Reorient or relocate the receiving antenna. steps 1, 3, and 4 may be performed. 3.2 Push the TIMER ON button again to set the time you want to start the operation.
9. ON/OFF Button: Push this button to start operation, push the button again to stop Transmission Indicator light fails to light.
•Increase the separation between the equipment and receiver. 3.3 Push the TIMER OFF button, the remote controller will show TIMER OFF, the last set
operation.
5. Do not dispose batteries as unsorted municipal waste. Collection of such waste separately for
•Connect the equipment into an outlet on a circuit different from that to which the receiver is time for STOP operation and the signal "h" will be shown on the DIGITAL display area. You DRY Operation
10. TIMER ON Button: Press this button to initiate the auto-on time sequence. Each press
special treatment is necessary.
1. DIGITAL DISPLAY area: This area will show the set temperature and, if in the TIMER
1. Push the MODE button to select DRY. connected. are now ready to reset the time to STOP operation.
will increase the auto-timed setting in 30 minutes increments. When the setting time
The design and specifications are subject to change without prior notice.
mode, will show the ON and OFF settings of the TIMER. If in the FAN mode, nothing is
2. Push the TEMP button to set the desired temperature within a range of 62°F ~ 86°F. •Consult the dealer or an experienced radio/TV technician for help. 3.4 Push the TIMER OFF button again to set the time you want to stop the operation.
displays 10h, each press will increase the auto-timed setting 60 minutes increments. To Install/Replace Batteries
appeared.
Consult with the sales agency or manufacturer for details.
•Changes or modifications not approved by the party responsible for compliance could void 3. Push the ON/OFF button, the OPERATION lamp lights and the air conditioner starts to 3.5 After setting the TIMER, there will be a one-half second delay before the remote
cancel the auto-timed program, simply adjust the auto-on time to 0.0.
Switch on the power and the OPERATION indication lamp on the display panel of the
2. TRANSMISSION Indicator: This indicator flashes one time when remote controller
operate in DRY mode at LOW fan speed. Push the ON/OFF button again to stop this unit users authority to operate the equipment. controller transmits the signal to the Air Conditioner. Then , after approximately another 2
11. SLEEP Button: Press this button to go into the Energy-Saving operation mode. Press it
indoor unit starts flashing, and turns off after flashes for 6 times.
transmits signals to the indoor unit.
operation. seconds, the signal "h" disappears and the set temperature will re-appear on the digital
again to cancel. This function is only can be used on COOL, HEAT and AUTO mode and
1. Use the MODE button to select AUTO.
3. ON/OFF Indicator: This symbol appears when the unit is turned on by the remote
display.
maintain the most comfortable temperature for you.
2. Push the TEMP button to set the desired temperature within a range of 62°F ~ 86°F.
controller, and disappear when the unit is turned off.
Note: Due to the difference of the set temperature of the unit and the actual indoor temperature,
NOTE: While the unit is running under SLEEP operation mode, it would be canceled if you press
3. Push the ON/OFF button to start the air conditioner. The OPERATION lamp on the
4. OPERATION MODE Indicator: When press the MODE button, it shows the current
Change the TIMER the Air Conditioner when in DRY mode will automatically operate many times without running
the MODE, FAN SPEED or ON/OFF button.
display panel of the indoor unit lights. The FAN SPEED is automatically set and there are no
operating mode: AUTO, COOL, DRY, HEAT (Cooling only model without), or FAN mode.
•To change the TIMER ON/OFF time, just press the corresponding TIMER button and reset the COOL and FAN mode.
fan speed indicators shown on the display panel of the remote controller.
5. LOCK Indicator: LOCK display is displayed by pushing the LOCK button. Push the LOCK
the time.
4. Push the ON/OFF button again to stop the unit operation.
button to clear display.
•To cancel the TIMER ON/OFF setting, just adjust the TIMER time to 0.0.
NOTE: The setting time is relative time. That is the time set is based on the delay of the current time.
REMOTE BUTTONS FEATURE BREAKDOWN
RG51M5/(C)EU, RG51M1/EU1
3.0V(Dry batteries Lr03 x2)
8m
23°F~140°F
COOL DRY
DIGITAL 1
DISPLAY area
TRANSMI-
2
SSION Indicator
OPERATION
4
MODE Indicator
5
LOCK Indicator
TIMER
6
DISPLAY Indicator
1
3
4
5
6
7
For more information visit www.mrcool.com.
DISPLAY SCREEN BREAKDOWN DISPLAY SCREEN BREAKDOWN
HEAT
OPERATING THE REMOTE
Display Panel
O
SE T TEMPER ATURE ( F)
FAN
AU TO
HIGH
COOL
MED
DRY
LOW
HEAT
TIMER ON OFF
TEMP
Fig. 2
ON /OFF
MOD E
FAN SPEED
TI MER O N
SWING SLEE P
FP
TI MER O FF
RESET LOCK
AIR
LED
D IR ECTION
DISPLAY TURBO
Fig. 1
4 7 6 5 3 2 1
FAN
3
ON/OFF Indicator
OPERATION
4
MODE Indicator
7
FAN SPEED Indicator
2
9
8
10
11
12
13
14
15