Black & Decker 9036 Manual page 5

reproductive harm.
Some examples of these chemicals are:
f lead from lead-based paints,
f crystalline silica from bricks and cement and other
masonry products, and
f arsenic and chromium from chemically-treated
lumber.(CCA)
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: Work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
f Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
CHARGING THE SCREWDRIVER (Fig. B)
Before attempting to charge your screwdriver, thoroughly
read all of the safety instructions.
To charge your screwdriver, follow the steps below.
1. Plug the output cord of the charger (6) into the socket
in the back half of the screwdriver handle (4) as shown
in Fig. B.
2. Plug the charger into any standard electrical outlet.
3. The red charge indicator light next to the socket in the
back half of the handle (5) will come ON indicating that
the battery is charging. This light will remain on as
long as the the screwdriver is connected to the
charger.
Charging Notes
The tool was sent from the factory in an uncharged
condition. Before attempting to use it, it must be charged
for 12 hours.
1. Charger will work best at normal room temperature.
2. The charger plug and the tool handle may become
warm while charging. This is normal and does not
indicate a problem.
3. The tool can be left on charge as long as you desire.
A minimum charge time of 8 hours is required to
recharge a completely discharged tool.
4. For most fix up jobs a charge of 3 to 4 hours adequate.
5. For long periods that the screwdriver will not be used,
it is recommended that it be fully charged, disconnected
from the charger and stored in a cool, dry location.
Warning! When disconnecting the screwdriver from the
charger, be sure to unplug the charger from the outlet first
then disconnect the charger cord from the screwdriver.
USE
Removing and Installing Bits (Fig. C)
To install a screwdriver bit (6) Fig. C simply insert it into
the cavity in the bit holder (3) until it snaps into place. To
remove the bit pull it straight out. If bit does not fit, rotate
the bit and reinsert it.
Adjusting the Handle
For optimum versatility, the handle can be be set to
different positions as shown in Fig. D. To adjust the handle
into the desired position.
Note: To avoid being pinched, grasp the handle below the
pinch point shown in Fig. D.
OPERATION (Fig. E)
Forward
f Press the button on the top (Clockwise Arrow) (8)
and the tool will run forwards.
f Release the button and the tool will stop.
Reverse
f Press the button on the bottom (Counter Clockwise
Arrow) (9) and the tool will run in reverse.
f Release the button and the tool will stop.
Operating in Manual Mode
f The tool can be used as a conventional non-powered
screwdriver whenever the forward/reverse button is
not depressed. With the button (ON/OFF)(1) in the
middle position, the tool will not activate.
HINTS FOR OPTIMUM USE
f Always use the correct type of screwdriver bit.
f If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
f Use the screwdriver manually as a non powered
screwdriver to loosen very tight screws or to firmly
tighten screws.
f Always hold the tool and screwdriver bit in a straight
line with the screw.
LUBRICATION
BLACK+DECKER tools are properly lubricated at the
factory and are ready for use.
BATTERY PACK REMOVAL
Important! This tool is designed for disassembly for
the purpose of battery pack removal and recycling. It
is not designed to be re-assembled by the consumer.
Before attempting to disassemble this tool, turn it on
and run it in either direction until it stops to ensure a
ENGLISH • 5