Maxi-Cosi Pria 70 Instructions Manual
  1. Manuals
  2. Brands
  3. Maxi-Cosi Manuals
  4. Car Seat
  5. Pria 70
  6. Instructions manual

Maxi-Cosi Pria 70 Instructions Manual

Convertible
Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Maxi-Cosi Pria 70

Summary of Contents for Maxi-Cosi Pria 70

  • Page 2 A. Before You Begin ......Pages 3-10 D. General Vehicle Installation ..Pages 38-46 A-1 Registration and Safety Notices D-1 Understanding Your Vehicle A-2 Understanding Your Child Restraint D-2 Vehicle Seating Position D-3 Choosing LATCH or Vehicle Belts D-4 Knowing Your Vehicle Belts D-5 Using Locking Clip D-6 Installing on Aircraft B.
  • Page 3 (TTY: 1–800–424–9153), or go to http://www.NHTSA.gov follow these instructions. After reading, if you still have questions or have any problems with this child restraint, please contact our Consumer Relations Department at: Dorel Juvenile Group, Inc. Website: www.maxi-cosi.com Manufacture Model Fax: 1-800-207-8182 Date...
  • Page 4 A-3 Understanding Your Child Restraint Front View Without TinyFit Infant Insert Front View With TinyFit Infant Insert Adjustable Headrest Cup Holder Headrest Adjustment Harness Release Instruction Storage Handle Lever (under flap) (attached to outside of seat) TinyFit Infant Insert Harness Tightening Strap Small Chest Clip Head Pillow...
  • Page 5 Harness System Detail With TinyFit Infant Insert Harness System Detail Without TinyFit Infant Insert Upper Harness Slots Harness Straps Headrest Harness Buckle Strap Slots (for larger children) Large Chest Clip Buckle Strap Slots Harness Straps Buckle Tongue Large Chest Clip Buckle TinyFit Infant Insert Lower Harness Slots...

  • Page 6: Product View And Parts

    Back View Side View LATCH Connector LATCH Adjuster Forward-Facing LATCH Belt Belt Path Top Anchorage Rear-Facing Belt Strap (Tether) Path Splitter Plate Level to Ground Line (on side of plastic shell) Seat Recline Handle Recline Base Top Anchorage Strap (Tether) Storage Headrest Adjustment Lever...
  • Page 7 B-3 Child Restraint Use Never take your child out of the child Failure to follow these warnings can result in the serious injury or death of your child. To help you restraint while the vehicle is moving. Never recognize instructions which are most critical to leave child unattended.

  • Page 8: Choose Position For Child

    C-1 Choose Position for Your Child 40-70 lbs (18.1-32 kg) and 43-52 in. Your child’s height, weight and age determine how (110.1-132.1 cm) and your child restraint should be placed in the vehicle. Over 1 Year Old 4-22 lbs (1.8-10 kg) and Forward-Facing using Top of Child’s Head Below 5-point harness...
  • Page 9 Head Pillow Unbuckle Harness (on select models) Press red button. Pull When using the head pillow, buckle tongues out. Place make sure it does not cover the harness straps out of the infant’s face in any way. way. To adjust the head pillow, slide the top together or apart for a proper fit.
  • Page 10 Pull Harness Straps Rear-Facing Position Out of TinyFit Infant Harness slot must be even Insert Slots in Shell with or just below the Lean the TinyFit infant shoulders. insert forward and pull the If the lowest harness slot is harness straps out of the above the child’s shoulders, shell.
  • Page 11 To Remove the TinyFit Infant Insert Push TinyFit Infant Insert into Back of Child If your child weighs more than 22 lbs. or the child’s Restraint head is at or above the TinyFit infant insert or if you are using this seat forward-facing, you MUST remove the TinyFit infant insert.
  • Page 12 Preparing Without the TinyFit Infant Insert Push Harness Straps into Lower Harness Slots in TinyFit Infant Insert Check Harness Height Insert the harness strap, With child in the seat, check buckle tongue and chest clip the location of the harness into the lower harness slot guide.
  • Page 13 To Adjust Harness/ To Change Buckle Headrest Height Position Loosen harness straps. Fully recline the child Squeeze the headrest restraint. Reach under the adjustment lever and seat between base and shell. move headrest up or down to the proper height and lock into place Locate buckle’s metal Do not use this child restraint rear-...
  • Page 14 C-4 Securing Child in Child Restraint Reach under seat between base and shell. Pull Position Harness buckle’s metal retainer Straps Over the completely through pad Child’s Shoulders. and shell. Pull up on buckle to make sure it is secured. The Buckle Harness buckle must not pull out.
  • Page 15 Check Harness C-5 Removing Child From Child Restraint Tightness Try to pinch the harness at Loosen Harness the shoulders. If you can Press on harness release pinch the harness strap, lever while pulling on tighten more. If your fingers harness straps above the slip off, the harness is tight buckle to loosen.

  • Page 16: Reclining Child Restraint

    C-6 Reclining Child Restraint C-7 Removing Seat Pad for Cleaning This child restraint has 3 Remove Harness Straps recline positions: from Splitter Plate Rear-facing - Use angle Fully loosen harness straps. position or 3. The level Locate splitter plate on the to ground line on the side of back of the child restraint shell...
  • Page 17 Pull Seat Pad Out from Insert Metal Retainer Behind Headrest Rotate the metal retainer Pull rest of pad off of shell. and then insert the retainer The headrest pad is not up through the shell and removeable. pad. Pull Buckle Out of Seat Cleaning Seat Pad From the front, pull buckle Hand wash pad with warm sudsy water, rinse clean and air...

  • Page 18: Replacing Seat Pad And Harness System

    C-8 Replacing Seat Pad and Harness Pull Harness Adjustment Strap Through Pad System Do not use child restraint without the seat pad. Pull Pad Over the Outside Slip Seat Pad Over and Edges of the Shell Behind Headrest Lay pad in child restraint and slip pad over the headrest.
  • Page 19 Thread Harness Straps With child restraint fully Into TinyFit Infant Insert reclined, reach under Upper Slots seat between base and shell. Pull buckle’s metal See section “Preparing With retainer completely TinyFit Infant Insert” for through pad and shell. correct harness slot location. Thread Harness Straps Into TinyFit Infant Pull up on buckle to make...
  • Page 20 Threading Harness Without TinyFit Infant D-1 Understanding Your Vehicle Insert Your vehicle’s features may be considerably different than those pictured here. Consult your vehicle owner’s manual to Thread Harness Straps help identify your vehicle’s specific features and locations. into Headrest Harness Slots Thread one harness strap into each headrest harness slots.
  • Page 21 D-2 Vehicle Seating Position D-3 Choosing LATCH or Vehicle Belts Some seating positions in your vehicle may not be safe for LATCH Anchor Bars The LATCH System this child restraint. Some vehicles do not have a seating position that can be used safely with this child restraint. If LATCH (Lower Anchors and you are not sure where to place the child restraint in your Tethers for CHildren) is a...
  • Page 22 several inches, then pull on it again. If it moves freely, it is an D-4 Knowing Your Vehicle Belts ELR vehicle belt. If it is locked and will not allow any more vehicle belt to come out, it is a switchable retractor. Review your vehicle’s owner manual for vehicle seat belt use with child restraints.
  • Page 23 Pull Vehicle Belt Across D-5 Using the Locking Clip Child Restraint A locking clip will not fix all types of vehicle seat belt Without the TinyFit infant problems. Review section D-4 and your vehicle’s owner insert (A), thread vehicle belt manual for vehicle seat belt use with child restraints.
  • Page 24 Attach Locking Clip D-6 Installing on Aircraft Thread both portions of the This restraint is certified for vehicle belt onto the locking aircraft use. clip, as close to the latch plate as possible. Use only on forward-facing aircraft seats. Follow instructions for vehicle Position Locking Clip installation.
  • Page 25 E-1 Preparing to Install Rear-Facing Never place a child rear-facing in a Rear-Facing With TinyFit Infant Insert: seating position with an active frontal 4-22 lbs (1.8-10 kg) and Top of Child’s Head is airbag. This can result in serious injury Below the Top of TinyFit Infant Insert.
  • Page 26 Tip: You may need to E-3 Install Rear-Facing with pull the pad off the front LATCH corners of plastic shell to help thread the LATCH belt across the shell. Do not use the LATCH system along with the vehicle lap or lap/shoulder belt. Check LATCH belt before each use.
  • Page 27 Note: Review your vehicle’s owner manual for LATCH belt use. It may be easier to tighten the LATCH belt through the belt path opening as Check for Proper Recline shown. Make sure level lines on side If your using the TinyFit of plastic shell are level with infant insert, loosen the ground.
  • Page 28 Note: Review the section D-4 to determine what kind of E-4 Install Rear-Facing with vehicle belts you have. Review your vehicle’s owner manual Vehicle Belts for vehicle seat belt use. Check for Proper Recline Make sure level lines on side of plastic shell are level Do not use the LATCH system along with the with ground.
  • Page 29 With the TinyFit infant insert Secure your child in (B), make sure harness the child restraint system is loose and headrest and check for proper recline. is up. Thread vehicle belt UNDER seat pad and TinyFit infant insert on top of buckle strap and out the opposite side.

  • Page 30: Preparing To Install Forward-Facing

    40-70 lbs (18.1-32 kg) and 43-52 in. (110.1-132.1 cm) F-1 Preparing to Install Forward-Facing and Over 1 Year Old. Forward-Facing using 5-point harness Safety Tip: Experts agree that children should remain rear-facing as long as possible. In this child restraint, your child can remain rear-facing up to 40 pounds and up to 40 inches.

  • Page 31: Adjusting Top Anchorage Strap

    F-3 Preparing to Install F-2 Adjusting Top Anchorage Strap (Tether) LATCH Forward-Facing The top anchorage strap (tether) is used for the Note: Pull the LATCH belt out of the rear-facing belt path forward-facing position only. if you have used this child restraint rear-facing. Note: We strongly recommend that you use the top Routing LATCH Belt anchorage strap (tether) in the forward-facing position.
  • Page 32 Place Child Restraint in Fasten one LATCH belt the Back Seat connector to the anchor Forward-Facing in the vehicle seat located in the vehicle seat bight. Place the child restraint flat Repeat for other side of on vehicle seat bench and child restraint.
  • Page 33 Secure LATCH Belts Check LATCH Belt Tightness You MUST fasten the LATCH belt connectors to Grasp the child restraint the side of plastic shell at the belt path with one as shown when using the hand. Push and pull the child vehicle seat belts.
  • Page 34 It maybe easier to tighten the Installation Tip: vehicle belt through the belt path opening as shown. Loosely attach the top anchorage hook (tether) before threading the vehicle belt. Consult vehicle’s owner manual for specific location. NOTE: If you cannot use the Tighten Top Anchorage top anchorage strap (tether), Strap (Tether)
  • Page 35 Trouble Shooting Replacement Parts Order Form If the child restraint buckle or harness release lever Complete the form below. Your model number with color code and sticks or you cannot get the straps tight enough around manufacturer date code MUST be included on the form to ensure child: DO NOT LUBRICATE.

  • Page 36: Replacement Parts List

    Replacement Parts List Warranty NOTE: If requested color is not available, similar color will be Dorel Juvenile Group, Inc. (DJG) warrants this product to the original substituted. Prices are subject to change. retail purchaser as follows: Part Cost Quantity Total Cost This product is warranted against defective materials or Buckle Strap/Buckle ..

Table of Contents