English - AEG PS216L Original Instructions Manual

Only use the saw with guards in good working order and properly
maintained, and in position.
When performing mitre, bevel or compound mitre cuts, adjust the
sliding fence to ensure the correct clearance from the blade.
Refrain from removing any cut-offs or other parts of the workpiece
from the cutting area whilst the machine is running and the saw
head is not in the rest position.
Never reach into the danger area of the machine when it is running.
Always use the protective shields on the machine.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of
safety as soon as the faults are discovered.
Do not clamp the protective swing guard.
Long workpieces must be adequately supported.
Do not replace the LED with a different type.
The handle lock must always be engaged when transporting the
mitre saw.
Connect the saw to a dust-collecting device when sawing wood.
Do not use this tool 's dust extraction as a vacuum cleaner to pick
up anything, such as hardness work pieces or nails etc. it will cause
the fan damage.
LASER
Do not stare into beam. Do not point laser light at other persons.
Do not view directly into beam with optical instruments (binocular,
telescope).
Do not point laser at reflective surfaces,
Avoid exposure to laser radiation. Laser may emit hazardous
radiation.
Do not replace the installed laser with a different type.
Any repairs must only be carried out by the authorized service
agent.
SPECIFIED CONDITIONS OF USE
The mitre saw can be used for sawing solid wood, bonded wood,
glued veneer, materials similar to wood, aluminium profiles, Non-
ferrous metals and plastics.
Stock having a round or irregular cross section (such as firewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for firm support.
RESIDUAL RISK
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special
attention to avoid the following:
• Impairment of hearing, restrict exposure and wear appropriate
hearing protection.
• Measures that can be taken by operator to possibly reduce the
effects of vibration and limit the amount of exposure.
• Health hazards caused by breathing dust developed when
sawing wood, wear a mask if necessary.
MAINS CONNECTION
Connect only to single-phase AC system voltage as indicated on
the rating plate. It is also possible to connect to sockets without an
earthing contact as the design conforms to safety class II.
Appliances used at many different locations including wet room
and open air must be connected via a residual current device (FI,
RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
A power spike causes voltage fluctuations and may affect other electrical
products in the same power line. Connect the product to a power supply
with an impedance equal to 0.3 Ω to minimize voltage fluctuations.
Contact your electric power supplier for further clarification.
MAINTENANCE
Always disconnect the plug from the socket before carrying out any
work on the machine.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the service
organization.
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and spare parts. Should components need to
be replaced which have not been described, please contact one of our
AEG service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Win-
nenden, Germany.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described
under "Technical Data" fulfills all the relevant provisions of the
directives
2011/65/EU (RoHS)
2006/42/EC
2014/30/EU
and the following harmonized standards have been used.
EN 61029-1:2009 + A11:2010
EN 61029-2-9:2012 + A11:2013
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997 + A1:2001 + A2:2008
EN 61000-3-2:2014
EN 61000-3-11:2000
EN 50581:2012
Winnenden, 2016-03-25
Alexander Krug / Managing Director
Authorized to compile the technical file
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB

English

21