Viking E-20 Product Manual page 9

Quick Programming Features
DESCRIPTION
First speed dial number
Second speed dial number
Third speed dial number
Fourth speed dial number
Fifth speed dial number
To clear any speed dial number
Talk/Listen Delay (.1 to .9 sec, factory set to .5 sec)
Call Length Time Out (0 to 9 min, 0 = disabled, factory set to 3 min)
Lap Counter (0 to 9, 0 = disabled, factory set to 0)
Dial Next Number on Ring No Answer
Dial Next Number on Busy (0 or 1, 0 = disabled, factory set to 1/enabled)
Security code (factory set to 845464)
Identification number (factory set to 987654)
Access Code (1-6 digits, blank = disabled, factory set to 123456)
Mic volume (0-9, 0 = ANC, factory set to 5)
Speaker Volume (0-9, factory set to 5)
Relay Activation Command ( 1 or 2 digits, QQQQ = QQ, Q#Q# = ##, 0-9 or 00-99, factory set to
QQ) (Relay Mode must be set to 0 = Door Strike)
Relay Activation Time (2 digits, 00-99 sec, 00= 0.5 sec, factory set to 05)
Relay Mode (0 = Door Strike, 1 = Outbound Call, 2 = In/Outbound Call, 3 = Doorbell, 4 = LV-1K
Control, factory set to 0)
Relay Activation Tone (Buzz) Volume (1 digit 0-3, 0 = off, factory set to 3)
Audio Detection Sensitivity (1-9, 1 = min, 9 = max, factory set to 5)
In-Band Call Progress Detection (0 or 1, 0 = OFF, 1 = ON, factory set to 0)
"Call Connected" LED Control (1 or 2, 1 = Automatic, 2 = Called Party Control / Q entered to light
LED, factory set to 1)
Speaker Mode
(0, 1 or 2, 0 = OFF/Silent Monitor, 1 = ON, 2 = OFF Until Answered, factory set to 1)
LED Mode
(0, 1 or 2, 0 = OFF/Silent Monitor, 1 = Entry Phone, 2 = Emergency Phone, factory set to 1)
Auto Answer/Ring (0, 1 or 2, 0 = OFF, 1 = ON, 2 = OFF with Ringer Enabled, factory set to 1)
DESCRIPTION
Diagnostic tones (used to check mic and speaker operation)
Enable Alternate Switch Action (factory setting)
Disable Alternate Switch Action
Enable Latching Commands (factory setting)
Disable Latching Commands
To add a Q at any point in the dialing string
To add a # at any point in the dialing string
Reset all Quick Programming Features to factory default settings
(after accessing the Touch Tone Programming Mode)
(0 or 1 = disabled, 2 - 9 = number of rings, factory set to 7)
MEMORY
DIGITS +
LOCATION
0-20 digits + #00
0-20 digits + #01
0-20 digits + #02
0-20 digits + #03
0-20 digits + #04
(no digits) + #00 - #04
1 digit (1-9) + #11
1 digit (0-9) + #12
1 digit (0-9) + #16
1 digit (0-9) + #17
1 digit (0 or 1) + #18
6 digits (0-9) + #19
6 digits (0-9) + #20
1-6 digits (0-9) + #21
1 digit (0-9) + #22
1 digit (0-9) + #23
1 or 2 digits + #24
2 digits (00-99) + #25
1 digit (0-3) + #26
1 digit (0-3) + #27
1 digit (1-9) + #28
1 digit (0 or 1) + #29
1 digit (1 or 2) + #30
1 digit (0-2) + #31
1 digit (0-2) + #32
1 digit (0-2) + #33
ENTER DIGITS
Q0
Q1
Q2
Q6
Q7
QQ
Q#
###
9