Mechanical Error History - Pioneer XV-HTD330 Service Manual

1

7.1.6 MECHANICAL ERROR HISTORY

QQ
3 7 63 1515 0
Mechanical Error History
A
Only if a mechanical error (FE error) has been generated, a mechanical error history containing up to the last eight errors is
displayed if you press the CHP/TIM key in Service Mode.
Errors are displayed in descending order, with the latest one at the top.
Description of the mechanical error history
1 Error number
The first two digits are for the error code, and the second
two digits are for the servo state.
Servo State
Error Code
B
2 Error number
The elapsed time from the time when the system was
turned on until an error was generated is displayed.
Note: If a later error time is shorter than the previous
error time, it means that the unit was turned off
then on again.
3 Description of errors
Error messages are displayed.
Example: If the error code is 0x13 (Focus lost timeout)
and the servo state is 0x05 (Disc judge), the
message becomes "Focus lost timeout in Disc
judge."
C
• List of the error codes
FOCUS ERROR
TE
Focus on error
L 13942296513
Focus off error
Focus lost error
Focus balance adjust error
Focus gain adjust error
Focus sweep error
Focus reflection error
D
TRACKING ERROR
Tracking on error
Tracking off error
Tracking lost error
Tracking balance adjust error
Tracking gain adjust error
STEPPING ERROR
Stepping on error
Stepping off error
Stepping lost error
Stepping move error
E
SPINDLE ERROR
Spindle on error
Spindle off error
Spindle lost error
Spindle CAV error
Spindle CLV error
ACQUISITION ERROR
www
PLL lost error
DECODER ERROR
ID lost error
DEVICE ERROR
F
SRAM error
94
1
http://www.xiaoyu163.com
2
0x0∗ FOCUS TIMEOUT
0x01 Focus on timeout
0x02 Focus off timeout
0x03 Focus lost timeout
0x04 Focus balance adjust timeout
0x05 Focus gain adjust timeout
0x06 Focus sweep timeout
0x07 Focus reflection timeout
0x2∗ TRACKING TIMEOUT
0x21 Tracking on timeout
0x22 Tracking off timeout
0x23 Tracking lost timeout
0x24 Tracking balance adjust timeout
0x25 Tracking gain adjust timeout
0x4∗ STEPPING TIMEOUT
0x41 Stepping on timeout
0x42 Stepping off timeout
0x43 Stepping lost timeout
0x44 Stepping move timeout
0x6∗ SPINDLE TIMEOUT
0x61 Spindle on timeout
0x62 Spindle off timeout
0x63 Spindle lost timeout
0x64 Spindle CAV timeout
0x65 Spindle CLV timeout
0x8∗ ACQUISITION TIMEOUT
0x83 PLL lost timeout
x ao
0xa∗ DECODER TIMEOUT
y
0xa3 ID lost timeout
. i
0xd∗
0xd1
XV-HTD330
2
http://www.xiaoyu163.com
3
8
Note: When an error has been generated, if the servo state
is "Disc judge," the disc tray opens, and if the servo
state is other than "Disc judge," the unit stops
(excluding a case of a device error with the error
code 0xd∗).
Indication contents
1
1
• List of the servo states
0x1∗ 0x00
Q Q
0x11 0x01
3 6 7 1 3
0x12 0x02
0x03
0x13
0x14 0x04
0x05
0x15
0x06
0x16
0x17 0x07
0x08
0x3∗
0x31 0x09
0x0A
0x32
0x0B
0x33
0x34 0x0C
0x0D
0x35
0x5∗ 0x0E
0x51 0x0F
0x52
0x53
0x54
0x7∗
0x71
0x72
0x73
0x74
0x75
0x9∗
0x93
u163
0xb∗
Note : 0 x & &
0xb3
.
3
4
2 9 9 4 2 8
Reset
Stop (inside position)
1 5 0 5 8 2 9 9 4
Stop (any position)
Braking for stop
New disc
Disc judge
Reserved 1
Playing
Start up
Seeking
Pausing
Reading BCA
Reserved 2
Tray open
Tray moving
m
co
code
(Only this part is displayed to a display)
4
9 9
2
3
2
3
2 8 9 9