Tool Specifications; Declaration Of Conformity; Dust/Chip Extraction - Bosch PSS 190 AC Operating Instructions Manual

OBJ_BUCH-2 609 001 137-001.book Page 3 Wednesday, May 11, 2005 3:33 PM

Tool Specifications

Orbital sander
Article number 3 603 ...
Rated power input
Preselection of orbital
stroke rate
No-load speed
Orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via
Velcro backing
— Attachment via clamping
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these val-
ues can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.

Declaration of Conformity

We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the
98/37/EC.
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge
Assembly

Dust/Chip Extraction

Integrated Dust Extraction with Dust Box
(see figures C1–C4)
Attach the dust box 3 onto the outlet piece 7 until it
latches.
To empty the dust box 3, pull off the dust box down-
ward.
Before opening the dust box 3, it is recommended to
loosen the dust from the filter element by gently striking
it against a firm support (as shown in the figure).
Grasp the dust box 3 by the recessed grip, fold the filter
element 8 upward and empty the dust box. Clean the
thin plates of the filter element 8 with a soft brush.
2 609 001 137 • 11.5.05
PSS 190 AC PSS 200 A PSS 200 AC PSS 250 A
C40 1..
W 190
–
rpm 12000
opm 24000
mm 2.0
mm – 93 x 185
mm 93 x 230
kg 1.6
/II
directives 89/336/EEC,
English–3
C40 0.. C40 1.. C40 2..
200 200
– –
12000 12000
24000 24000
2.0 2.0
– 93 x 185
– 93 x 230 93 x 230
1.6 1.6
/II /II
External Dust Extraction (see figure D)
Insert a vacuum hose 9 onto the outlet piece 7. Con-
nect the vacuum hose 9 to a vacuum cleaner. See the
overview for connecting to various vacuum cleaners at
the end of these operating instructions.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum
cleaner.
Replacing the Sanding Sheet
Before any work on the machine itself, pull the
mains plug.
When attaching a new sanding sheet, remove any dust
or debris from the sanding plate 5 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that
the punched holes in the sanding sheet match with the
holes in the sanding plate.
Sanding Sheets with Velcro Backing
(PSS 200 A/PSS 250 A/PSS 250 AE)
(see figure A)
The sanding plate 5 is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 6, free the Velcro
backing of the sanding plate 5 from any debris by tap-
ping against it in order to enable optimum adhesion.
Position the sanding sheet 6 flush alongside one edge
of the sanding plate 5, then lay the sanding sheet onto
the sanding plate and press it against it with a light turn-
ing motion in clockwise direction.
To remove the sanding sheet 6, grasp it at one of the
tips and pull it off from the sanding plate 5.
PSS 250 AE
C40 2..
250 250
–
12000 7000–12000
24000 14000–24000
2.0 2.0
93 x 185
93 x 230
1.6 1.6
/II /II