McIntosh MA6300 Owner's Manual

McIntosh MA6300 Owner's Manual

Integrated amplifier
Hide thumbs Also See for MA6300:

Advertisement

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com
MA6300

Integrated Amplifier

Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MA6300 and is the answer not in the manual?

Questions and answers

Summary of Contents for McIntosh MA6300

  • Page 1: Integrated Amplifier

    McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com MA6300 Integrated Amplifier Owner’s Manual...
  • Page 2: Safety Instructions

    The lightning flash with arrowhead, within an equilateral The exclamation point within an equilateral triangle is triangle, is intended to alert the user to the presence of intended to alert the user to the presence of important uninsulated “dangerous voltage” within the product’s en- operating and maintenance (servicing) instructions in the closure that may be of sufficient magnitude to constitute literature accompanying the appliance.
  • Page 3: Table Of Contents

    MA6300 Integrated Amplifier. Please Take A Moment Fax: 607-723-1917 2. The Main AC Power going to the MA6300 and any The serial number, purchase date and McIntosh Dealer other McIntosh Component(s) should not be applied Table of Contents...
  • Page 4: Connector And Cable Information

    Input Connectors on the MA6300. Refer to the dia- grated Amplifier. The Power Amplifier section of gram for connection: the MA6300, with a power output of 100 watts per • Illuminated Power Meters PIN 1: Shield/Ground channel, will drive a pair of quality loudspeakers to a...
  • Page 5: Dimensions

    Dimensions Dimensions The following dimensions can assist in determining the best location for your MA6300. There is additional information on the next page pertaining to installing the MA6300 into cabinets. Front View of the MA6300 " 44.45cm " " 19.37cm 18.10cm...
  • Page 6: Installation

    Installation Installation The MA6300 can be placed upright on a table or " 1/16 shelf, standing on its four feet. It also can be custom 43.34cm installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom...
  • Page 7: Rear Panel Connections

    Moving Magnet Component or Power Control unit Jacks to the POWER AMP for 4 or 8 ohm phono cartridge when the MA6300 is turned on IN Jacks and are needed for loudspeakers normal operation Connect the MA6300 power...
  • Page 8: How To Connect Power And Data Control

    MA6300 Remote Control. For additional information refer to “Connector and Cable Information” on page 4. 1. Connect a Control Cable from the MA6300 POW- ER CONTROL Jack to the Power Control In on the McIntosh SACD/CD Player.
  • Page 9: How To Connect Audio Components

    CD Player connected to the CD2 INPUTS may be used instead of the Balanced CD1 Inputs. 2. Connect an Audio Cable from a McIntosh Tuner 1 Fixed Outputs to the MA6300 TUNER INPUTS. 3. Connect an Audio Cable from a Turntable to the PHONO INPUTS and the Turntable Ground Con- nection to the GND grounding post.
  • Page 10: How To Connect Loudspeakers

    Connections have been made. polarities. Failure to observe this could result in 3. Connect the MA6300 Power Cord to a live AC Figure 3 Figure 4 Figure 2 Electric Shock. For additional instruction outlet.
  • Page 11 Connecting Loudspeakers McIntosh Loudspeaker McIntosh Loudspeaker To AC Outlet...
  • Page 12: How To Connect An External Power Amplifier

    How to Connect an External Power Amplifier How to Connect an external Power Amplifier The MA6300 has the ability to be connected to an ex- ternal Preamplifier and/or Power Amplifier. In the ex- ample below, the MA6300 is connected to an external McIntosh Power Amplifier and to a McIntosh Loud- speaker with Bi-amplifer connections.
  • Page 13: Front Panel Displays, Controls, Push-Buttons And Jack

    Source Push-buttons Push to mute the audio from STANDBY/ON Push-button dynamic headphones, for private select audio signals from the Loudspeakers (Head- switches the MA6300 ON listening seven inputs for listening phones are not affected) or OFF (Standby) and resets the microprocessors...
  • Page 14: How To Operate The Ma6300

    Power Guard During normal operation, the Front Panel Power Guard Indicators will momentarily illuminate during peaks in the audio signals. In the event the MA6300 overheats, due to improper ventilation and/or high am- bient temperature, the internal protection circuits will activate.
  • Page 15 Note: The MA6300 TAPE OUTPUTS are not affected by the VOLUME or BALANCE controls. Reset of Microprocessors In the unlikely event the controls of the MA6300 stop functioning, the microprocessors can be reset by per- forming the following: 1. Press and hold in the STANDBY/ON Push-button for approximately five seconds.
  • Page 16: Remote Control Push-Buttons

    Selects Functions as a “shift” key when used with the AM or FM push-buttons to select Output 1 or 2 Selects one of the seven available Audio Sources Note: Push-buttons whose function is not identified above are for use with other McIntosh Products.
  • Page 17: How To Operate By Remote Control

    Push-button to seek the next available station. MA6300 via the Data Ports. Press and hold a Seek or Seek Push-button to seek Note: If at any time the MA6300 seems unresponsive to HRO70 Remote Control Commands press the continuously from station to station. Push-button first. Band...
  • Page 18: Specifications

    25.3V across 4 ohms output is rated power or less per channel with both channels operating for any combination of frequencies Note: Refer to the rear panel of the MA6300 for the cor- rect voltage. Output Load Impedance from 20Hz to 20,000Hz.
  • Page 19: Packing Instruction

    #10 x 2-1/4” wood screws needed, please call or write Customer Service Depart- 104033 #10 x 1-3/4” flat washer ment of McIntosh Laboratory. Refer to page 3. Please see the Part List for the correct part numbers. 017937 Plastic foot 100159 #10-32 x 3/4”...
  • Page 20 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04116700...

Table of Contents