Bissell POWERWASH DELUXE Manual page 7

C3 – Filling the 2-in-1 water tank
1. Remove tank from base of machine by
lifting tank carry handle. Carry like a bucket
to the sink.
2. Pull upward on bottom edge of latch in
the back of tank to unhook and remove lid.
3. Pull up on bladder fill cover that says
"Fill Here". Fill the bladder with hand hot
(60°C/140°F MAX) tap water. Do not boil
or microwave water as it can destroy the
bladder.
4. Using measuring cup provided, fill to
indicated fill line on measuring cup and pour
in to bladder.
NOTE: Always use genuine BISSELL 2X
formulas to maximize cleaning and for the
safety of your machine.
5. Replace tank lid by seating front edge of
tank before back, then lock latch in place.
NOTE: Remember to secure lid and test to
make sure it is secure before picking up
tank.
6. Place tank into machine base, seating
firmly in place.
C4 – Carpet cleaning
1. Plug into a proper outlet. Set ReadyTools
dial to Floor Cleaning setting. Turn power on
by pressing red power pedal
machine with your foot.
2. With your foot, press gray recline pedal
(a) located on back of machine next to red
power pedal.
3. While pressing spray trigger, make one
slow forward wet pass and another back.
Caution: do not overwet.
4. Release spray trigger and make one slow
forward and backward pass over same area.
5. Repeat cleaning passes until solution
being suctioned up appears clean. Continue
passes without pressing spray trigger
until you can't see any more water being
suctioned up. Repeated passes will help
aid in dry time.
NOTE: You may notice hair and debris
deposits on the carpet or in the tank that
were loosened by the cleaning action. This
debris should be picked up and thrown
away.
Some Berber carpets have a tendency to fuzz with wear. Repeated
strokes in the same area with an ordinary vacuum or deep cleaner
may aggravate this condition.
C5 – Empty the 2-in-1 water
tank/clean removable nozzle
1. Press power pedal
water tank from base using tank carry
handle. Carry tank like a bucket to a utility
sink or outside where you will dispose of
dirty water.
2. Pull upward on bottom edge of latch in
the back of tank to unhook and remove lid.
3. Empty dirty water from back corner of
tank.
4. After each use, remove any debris trapped
in red lint screen on base of machine while
tank is still removed.
5. After each use, remove nozzle by
grasping each side of top of nozzle and
pulling forward. Clean nozzle by rinsing
under running water.
6. When finished, replace nozzle by slightly
raising front of machine to line up slots on
each side of the base with hooks on each
side of nozzle. Attach at base first and then
push forward to click nozzle into place.
NOTE: If nozzle is not attached properly,
loss of suction will occur.
7. To continue carpet cleaning, refer back to
"Carpet cleaning" instructions in section C4.
If cleaning is complete, refer to "Care and
on back of
Storage" in section D on page 8.
lemon or pine oil may damage this appliance and void the
guarantee. Chemical spot cleaners or solvent-based soil removers
should not be used. These products may react with the plastic
materials used in your deep cleaner causing cracking or pitting.
Check for colourfastness in an inconspicuous place. If possible,
check upholstery stu ng. Coloured stu ng may bleed
through fabric when it becomes wet.
off. Remove 2-in-1
To reduce the risk of fire, use only BISSELL deep
cleaning formula for full size machines in your
deep cleaner. Use of cleaning formulas that contain
Take care not to run over loose objects or edges
of area rugs. Stalling the brush may result in
premature belt failure.
To reduce the risk of electric shock, push power
button o and disconnect plug from
electrical outlet before performing maintenance
or troubleshooting checks.
www.BISSELL.com
7