Subscribe to Our Youtube Channel
Related Manuals for FireClass Duo-Cel
Summary of Contents for FireClass Duo-Cel
- Page 1 FIRECLASS DUO-CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: APPROVED BY: JBJ DUO-CEL FIRE DETECTION/ALARM PANEL Installation & Commissioning Manual PAGE 1 of 29...
-
Page 2: Table Of Contents
ESISTOR IRING IAGRAM 4.2 P ......12 INSTALLATION HECKS 8 – T ..7 IGURE IRING IAGRAM 4.2.1 DUO-CEL Panel Installation 9 – A ... 8 IGURE LARM IRCUIT IRING IAGRAM Instructions ............ 12 10 – R IGURE EMOTE NDICATORS... -
Page 3: Introduction
DIODE 1N4002 1.1 Panel Identification The DUO-CEL panel & Repeater type can be identified from the Part Number on the side of the enclosure (see section 13. for location details). 2.3 Fire Relay Output The table below shows the part numbers. -
Page 4: Remote Control Input
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: The volt-free relay contacts are rated at pulse until the resistor is removed. The Alert/Evac On LED will illuminate on the panel and the internal 30Vdc with a maximum current of 1A. -
Page 5: Open Collector Outputs
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: Figure 3 – Remote Control I/P connections 2.6.1 Disabled Output The Disabled output is activated when any 10k ¼ W EOL disablements exist on the panel. -
Page 6: Standard Panel Resistor Zone Configuration
Z1 + Z1 – 2.8.4 Maximum Number of Devices on a Zone For the standard panel with 10uF EOL capacitor, the maximum number of detectors & MCPs per zone is limited to 32 or less (see DUO-CEL Application Guide). PAGE 6 of 29... -
Page 7: Iring Diagram
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: Figure 7 – Resistor EOL Zone Wiring Figure 8 – Twin-Wire Zone Wiring Diagram Diagram 6K8 to 3K9 (¼ 4W) end-of-line resistor EOL Device. -
Page 8: Publication: Issue No. & Date
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: Figure 9 – Alarm Circuit Wiring Diagram Figure 10 – Remote Indicators Wiring Diagram 10K ¼ W EOL Resistor Current Limiting Resistors 590R 1.5W... -
Page 9: Wiring Diagram . 8 Iagram
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP ISSUE No. & DATE: 01/03/12 should be connected via another set of twisted pair 2.9 Panel to Repeater Wiring cores. The Repeater RS485 communication and 24Vdc If the cable includes a screen then this should be power connections should all be made via a single earthed at the panel &... -
Page 10: Panel To Repeater Wiring
DUO-CEL system. power supply equipment which is Reference should be made to the DUO-CEL powered by 230VAC mains supply Application manual for technical details and description of panel features. Warning: The power supply uses Install all field wiring and equipment hazardous voltages. - Page 11 FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: IMPORTANT NOTES ON BATTERIES: DANGER: incinerate batteries. If placed in a fire, the batteries may rupture, with the DANGER: Batteries are electrically potential to release hazardous...
-
Page 12: Pre-Installation Checks
1 Battery clamp (may already be fitted in panel) All items, except for the battery fuse, will be required for the installation of the panel. 4.2.1 DUO-CEL Panel Installation Instructions The front cover should have been removed as detailed above in the pre-installation checks. The... - Page 13 FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: NOTE: Only battery leads supplied, with insulated connectors. 12. Fix the control board (with PCB cover) back into the enclosure, bringing the leads from the power supply unit underneath the control board and over the right-hand battery.
-
Page 14: Battery Removal & Replacement
4.2.2 Battery removal & Replacement device on the circuit. 21. Ensure all 12 DIL switches on the panel are Please refer to the FIRECLASS DUO-CEL OFF. logbook for details on how and when to replace 22. Connect the Zone EOL devices as follows: the standby batteries. -
Page 15: Baq35T24 1.5A P Connections
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: Figure 12 – BAQ35T24 1.5A Power Supply Connections Incoming Mains Cable Secured with a cable tie to the backbox Leave the Earth wire 3cm... -
Page 16: Duo-Cel Repeater Installation
WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 4.2.3 DUO-CEL Repeater Installation iii) Control Panel installation manuals. Instructions iv) Installation manuals for all equipment connected to the system. The Repeater installation is generally the same as v) Site-specific configuration details. -
Page 17: Powering Up
5.6.1 Basic Default Configuration 4. All sounders, detector heads and call points should now be connected. Remember to When first powered up, the DUO-CEL panel can be remove any links fitted to detector bases. Be operated in the factory default configuration: very careful to maintain correct polarity at each ... -
Page 18: Operating The Engineer's Functions
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 6. Operating the Engineer’s depending on the panel) or if no buttons are pressed for 30 seconds. functions Note that in the Dependency Configuration mode, The Engineer‟s configuration facilities are controlled... -
Page 19: Zone 1 Non-Latch Operation
On the display, the left zonal fire LED operates for The DUO-CEL panel is designed to monitor for low detector alarms, the right zonal fire LED operates impedance faults to earth on the field cables. Earth for MCP alarms. -
Page 20: Ommissioning The Panel
1 and check that: The yellow zone fault LED illuminates. 3. Use the Alarm Test facility [see DUO-CEL User Manual] or press the Evacuate button to operate The Sounder Fault LED and General Fault sounders. -
Page 21: Fire Signal Output
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: and then are silent. Deactivate the Class disconnecting one battery lead to create a PSU Change switch or timer. Fault indication (may take up to 60 seconds), the internal buzzer &... -
Page 22: Repeater Testing
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 10. Configure the panel to communicate with two Reset the MCPs and press the RESET button repeaters as detailed in section 6.2. on the repeater. Check that the panel and repeaters return to the quiescent state. -
Page 23: Site Configuration
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: have insulating sleeving placed on the leads for 9. System Maintenance safety. System maintenance details can be found in the logbook. SLEEVING DEVICE... -
Page 24: User Indications
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 10. User Indications General Indicator Section Indicator Colour Operating Condition Supply On Green OFF: No mains or battery power, ON: Panel has power (battery and/or mains) -
Page 25: User Controls
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 11. User Controls SUPPLY ON EVACUATE GENERAL FIRE GENERAL FAULT GENERAL TEST SILENCE BUZZER GENERAL DISABLE ALERT / EVAC ON SILENCE / RESOUND... -
Page 26: Pcb Layouts
PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 12. PCB Layouts Figure 13 illustrates the control board for the DUO-CEL 8-zone panel with the PCB cover fitted. Figure 13 – Panel control board and PCB cover REMOTE CONTROL INPUT:... -
Page 27: Cover
WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: Figure 14 illustrates the control board for the DUO-CEL repeater with the PCB cover fitted. Figure 14 – Repeater control board and PCB cover 24VDC RS485 INPUT NOTE: COMMS. -
Page 28: G Eneral A Ssembly D Rawing
FIRECLASS DUO -CEL EQUIPMENT: WRITTEN BY: RKP OM_FC_DUO-CEL_INST PUBLICATION: CHECKED BY: AP 01/03/12 ISSUE No. & DATE: 13. General Assembly Drawing PAGE 28 of 29... -
Page 29: General Assembly Drawing 14. Alarm Count Display
0 to 1023. The count operation. can be reset at any time by pressing the Alarm Figure 15 – Alarm Count LED assignment EARTH FAULT FC DUO-CEL 8 ZONE 1801306 MONITORING VALUE INDOOR USE SUPPLY ON...
Need help?
Do you have a question about the Duo-Cel and is the answer not in the manual?
Questions and answers