Advertisement
Quick Links
T
ECHNICAL INFORMATION
Models No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Models VC1310L, VC2510L and VC3210L are Wet & Dry
vacuum cleaners approved for Dust Class L of EC regulations,
featuring Automatic on/off system that operates simultaneously
as connected power tool is switched on/off.
Their other main benefits are:
High maneuverability and easy mobility
High repairability
Compact and lightweight design for easy storage
Self-cleaning prefilter of our unique design
These models are also available with cleaning set as
"X1 models"; VC1310LX1, VC2510LX1, VC3210LX1.
S
pecification
Voltage (V)
110
120
220
230
240
Model No.
Wet/Dry type
Automatic on/off system interlocked with the switch
of connected power tool
Continuous rating input: W
Max. air flow: m
3
Max. sealed suction: kPa
Tank capacity: L
Noise: dB
Variable suction power control by dial
Protection from electric shock
Power supply cord: m (ft)
Weight according to EPTA-Procedure 01/2003: kg (lbs)
*1: with Hose complete 28-3.5 *2: with Hose complete 38-2.5
S
tandard equipment
For all models:
Hose complete 28-3.5 set .......... 1 set
(incl. Front cuffs 38)
Holder 10-33 ............................. 6 pcs
Front cuffs 22 ............................ 1 pc
Front cuffs 24 ............................ 1 pc
For
:
VC1310L/ X1
Plastic dust bag 650x650 .......... 1 pc
For
VC2510L/ X1, VC3210L/ X1:
Plastic dust bag 800x650 .......... 1 pc
For all models:
Plastic dust bag set .................... 1 set
(incl. 10 pcs of the Plastic dust bag
described above.)
Note: The standard equipment for the tool shown above may vary by country.
VC1310L, VC2510L, VC3210L
Vacuum Cleaners
Current (A)
Cycle (Hz)
10.0
50/ 60
9.2
50/ 60
5.0
50/ 60
4.8
50/ 60
4.6
50/ 60
/minute
Wet
Dry
For
Cleaning set ..................... 1 set
Includes one each of:
-Hose complete 38-2.5
-Straight pipe
-Bending pipe
-Nozzle assembly
-Corner nozzle
For
Pipe holder ........................ 1 pc
L
W
Model No. VC1310L
Length (L)
Width (W)
Height (H)
Continuous Rating (W)
Input
1,050
1,050
1,050
1,050
1,050
VC1310L
7
13
72
9.6 (21.2)
VC1310LX1, VC2510LX1,
:
VC3210LX1
:
VC1310LX1
[VC2510L]
[VC1310L]
L
H
W
Dimensions: mm (")
VC2510L
366 (14-3/8)
432 (17)
334 (13-1/8)
416 (16-3/8)
420 (16-1/2)
451 (17-3/4)
Max. Output (W)
Output
---
---
---
---
---
VC2510L
VC3210L
Wet & Dry
Yes
1,050
2.0*
/ 3.5*
1
2
22.0
14
25
73
Yes
Grounding
5.0 (16.4)
10.5 (23.2)
14.5 (32.0)
O
ptional accessories
Hose complete 28-2.5/ 28-3.5/
28-5.0/ 38-2.5/ 38-5.0,
Front cuff 22/ 24/ 38,
Holder 10-33, Plastic dust bag set,
Powder filter, Dumper, Pre-filter,
Filter for wet type,
Paper dust bag 15L/ 25L,
Straight pipe, Bending pipe,
Nozzle assembly, Corner nozzle,
Anchor nozzle, Round brush,
Cleaning set, Nozzle for wet type,
Pipe holder
PRODUCT
P 1/ 23
[VC3210L]
H
VC3210L
552 (21-3/4)
398 (15-5/8)
685 (27)
---
---
---
---
---
27
32
73
Advertisement
Related Manuals for Makita VC1310L
Summary of Contents for Makita VC1310L
- Page 1 Description [VC3210L] Vacuum Cleaners ONCEPT AND MAIN APPLICATIONS Models VC1310L, VC2510L and VC3210L are Wet & Dry [VC1310L] vacuum cleaners approved for Dust Class L of EC regulations, featuring Automatic on/off system that operates simultaneously as connected power tool is switched on/off.
-
Page 2: Necessary Repairing Tools
Stop ring E-7 Switch lever Switch dial Outlet [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section DISASSEMBLING See Fig. 2. (1) Release Hook for separating the Motor section from Tank section. Fig. 2 VC1310L VC2510L VC3210L Hook Hook Hook Motor section Tank section... - Page 3 P 3/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section (cont.) DISASSEMBLING (2) Remove the screws drawn in Fig. 3 for separating Cowling complete from Tank cover complete. Fig. 3 Opening Base hook, remove 4x35 Tapping screw (3pcs.) Grip 4x35 Tapping screw (3pcs.) 4x65 Tapping screw (3pcs.) Lifting up Grip, remove 4x65 Tapping screw (3pcs.)
- Page 4 P 4/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section (cont.) DISASSEMBLING (4) Remove the Motor section and remove Fan 62 as drawn in Fig. 5. Fig. 5 4. Disassemble Motor section from 5. Remove Motor cover, Seal ring 70 6. Remove Fan 62 by turning Tank cover complete.
- Page 5 P 5/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor Section (cont.) DISASSEMBLING (6) After removing Endbell and Field, Motor section is disassembled as drawn in Fig. 7. Fig. 7 1. Disassemble Endbell and Field from Base by 2. Remove Fan cover by pushing with Slotted screwdriver. unscrewing two M5x60 Pan head screws.
- Page 6 P 6/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section (cont.) ASSEMBLING (1) Assembling Armature to Base, pass Flange, upper-side Fan 125 and Spacer through Armature shaft, and mount Return vane. Refer to Fig. 7. (2) After assembling lower-side Fan 125 and Flat washer 10 to Armature shaft, tighten M8 Hex nut by turning clockwise. However, M8 Hex nut is tightened provisionally in this step.
- Page 7 P 7/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section (cont.) ASSEMBLING (4) Assemble Field, Endbell, Fan 62 and Seal ring 70 as drawn in Fig. 9. Fig. 9 Rubber ring 120 1. Insert the flat of Rubber ring 120 to the groove Groove on on Base so that the edge of Separator complete Rubber ring 120...
- Page 8 P 8/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-1. Motor section (cont.) ASSEMBLING (5) Assemble Motor section to Tank cover complete as drawn in Fig. 10. Fig. 10 Round depressions on the back side of Support ring Protrusion Tank cover 1. Fit the round depressions of Support ring to the round protrusions of Tank cover.
- Page 9 P 9/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-2. Float section DISASSEMBLING (1) Release Hook for separating the Motor section from Tank section. See Fig. 2. (2) Disassemble Float cage as drawn in Fig. 11. Fig. 11 1. Disassemble Float cage from the bottom of Tank cover by loosening three 4x25 Tapping screws.
- Page 10 P 10/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-3. Grip DISASSEMBLING Remove Grip as drawn in Fig. 13. Fig. 13 1. Fold Grip on Cowling complete. 2. Insert slotted screwdriver into the center side gap between Grip and Cowling complete. 3. By pushing Grip toward outside, 4.
- Page 11 [3]-4 Caster 50 for VC1310L and VC2510L: Four wheel type) DISASSEMBLING Casters for VC1310L are different from those for VC2510L in the length of Socket stem. However, they can be removed and assembled in the same way. (1) Separate Motor section from Tank section as drawn in Fig. 2.
- Page 12 P 12/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-4. Caster 50 for VC1310L, VC2510L (Four Wheel type) ASSEMBLING Refer to Figs. 16 and 17. Set each Caster 50 in place. Fig. 16 (Rear) Caster 50 (Front) Caster 50 with Wheel lock without Wheel lock...
- Page 13 P 13/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-4A. Caster 75 and Caster 170 for VC3210L (cont.) ASSEMBLING Caster 75 can be assembled as illustrated in Fig. 19. Fig. 19 1. Set 1R275 between the two wheels to protect Caster 75 from damaging. 2.
- Page 14 P 14/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-5. Bumper for VC1310L, VC2510L ASSEMBLING Bumper can be assembled as drawn in Fig. 22. Fig. 22 1. Set Bumper to the rear side of Tank 2. Fitting the Bumper from the rear side to while aligning the Triangle mark to Outlet installation side, assemble it to Tank.
- Page 15 3. Mount Rubber holder to the other end of Holder. 4x28 Tapping screw (3pcs.) Rubber holder O riing 56 Inlet VC1310L Holder plate Holder Rubber holder 4x28 Tapping screw (3pcs.) O ring 56 Inlet VC2510L (Assembling way is the same as VC1310L.)
- Page 16 P 16/ 23 epair [3] DISASSEMBLY/ASSEMBLY [3]-6A. Inlet for VC3210L ASSEMBLING Set Inlet in place as drawn in Fig. 25A. Fig. 25A VC3210L 1. Inserting Holder into Holder plate, pass the Holder through Tank. 2. Assemble Inlet to Inlet cover. Holder plate Inlet cover Holder...
-
Page 17: Circuit Diagram
P 17/ 23 ircuit diagram Fig. D-1 Color index of lead wires' sheath Green Black White Blue Purple Orange Gray Motor assembly Power supply cord Strain relief Blue lead wire is used for some countries. Line filter Note: Line filters are not used for some countries. -
Page 18: Wiring Diagram
P 18/ 23 iring diagram Fig. D-2 Wiring to Outlet Orange Lead Wire: Purple Lead Wire: Green or Green/Yellow Lead Wire: Outlet viewed from Outlet viewed from Destinations outside of Tank inside of Tank CO 3 (grounding) Europe and Other countries CO 2 CO 1 UK (240V) - Page 19 P 19/ 23 iring diagram Fig. D-3 Wiring of Field lead wires Top view of Motor assembly (before mounting Motor cover and Fan 62) Field lead wires for connecting to Brush holder Field lead wire for have to be fixed with the Lead wire holder as connecting to Brush holder drawn below.
- Page 20 P 20/ 23 iring diagram Fig. D-4 Wiring in Separator complete Pull out Field lead wires using the space Separator between Separator complete and complete Tank cover complete. Do not make a slack between Motor assembly and Separator cover. See Fig. D-6 in detail for mounting Carbon brush.
- Page 21 P 21/ 23 iring diagram In case of VC1310L and VC2510L, Holder plate is connected to Tank with Grounding lead wire as drawn in Fig. D-5. Fig. D-5 Wiring of Grounding Lead wire in Tank VC1310L Pass Lead wire through this cut portion.
- Page 22 P 22/ 23 iring diagram Mount Carbon brush and put the Pig tail ( lead wire of Carbon brush) as drawn in Fig. D-6. Fig. D-6 Wiring of Pigtail (Lead wire of Carbon brush) 1. Insert Carbon brush into Brush holder 2.
- Page 23 P 23/ 23 iring diagram Fig. D-7 Assembling Outlet to Switch base complete Assembling Outlet to Switch base complete while paying attention to the following matters. 1. Face the hinge to supper side. 2. Put Rubber sheet between Switch base camplete and Outlet.