Table of Contents
Advertisement
C-1
OPTIONAL EQUIPMENT
K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR
SMALL WELDERS - For road, off-road and in-plant
and yard towing. (For highway use, consult applicable
federal, state and local laws regarding requirements
for brakes, lights, fenders, etc.)
Order K957-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-2 Fender & Light Kit
K965-1 Cable Storage Rack
K889-2 & -3 Two-Wheel Undercarriage - For moving
by hand. Overall Width 29 in (.74m) Both have pneu-
matic tires. Puncture proof tires included with K889-3.
K1737-1 FOUR WHEEL ALL-TERRAIN UNDER-
CARRIAGE - For moving by hand at construction
sites. Heavy duty puncture resistant pneumatic tires.
K1770-1 UNDERCARRIAGE (FACTORY) - For mov-
ing by hand on a smooth surface. One or two gas
cylinders can be mounted on the rear of the undercar-
riage with the installation of K1745-1 Cylinder
Holder(s). Heavy duty puncture resistant pneumatic
tires and front caster.
K1745-1 WELDING GAS CYLINDER LPG TANK
HOLDER
Holds Welding Gas Cylinder for use on K1770-1
Undercarriage. One or two may be installed on an
undercarriage.
K1788-1 ROLL CAGE - Gives added damage protection.
Attaches to K1737-1, K1770-1, and K957-1.
K886-1 CANVAS COVER -To protect the ZR-8 when
not in use. Made from attractive red canvas material
which is flame retardant, mildew resistant, and water
repellent.
K802R POWER PLUG KIT - provides four 120V plugs
rated at 15 amps each and one dual voltage, Full
KVA plug rated at 120/240V, 50 amps.
K802N POWER PLUG KIT - Provides four 120V
plugs rated at 20 amps each and one dual voltage, full
KVA plug rated at 120/240V, 50 amps.
K704 ACCESSORY KIT - Includes 35 ft (10.7m) 2/0 AWG
electrode cable, 30 ft. (9.1m) 2/0 AWG work cable, head-
shield with No. 12 filter, GC300 work clamp and Cooltong®
300 electrode holder. Cables are rated at 400 amps, 100%
duty cycle.
ACCESSORIES
K875 ACCESSORY KIT - For Stick welding. Includes 20 ft
(Field Installed)
(6.1m) #6 electrode cable with lugs, 15 ft. (4.6m) #6 work
cable with lugs, headshield, Filter plate, work clamp and
electrode holder and sample pack of mild steel electrode.
150 amp capacity.
K894-1 SPARK ARRESTER KIT - Includes a heavy gauge
steel, approved spark arrester and clamp for easy mounting
to muffler exhaust pipe.
K1690-1 GFCI RECEPTACLE KIT -
approved120V ground fault circuit interrupter duplex type
receptacle with cover and installation instructions.
Replaces the factory installed 120V duplex receptacle.
Each receptacle of the GFCI Duplex is rated at 20 Amps,
the maximum total current from the GFCI Duplex is limit-
ed to the 20 Amps. Two kits are required.
K1816-1 FULL KVA ADAPTER KIT - Plugs into the
120/240V NEMA 14-50R receptacle on the case front
(which accepts 4-prong plugs) and converts it to a NEMA 6-
50R receptacle, (which accepts 3-prong plugs.)
T12153-9 FULL-KVA POWER PLUG - One dual voltage
plug rated at 120/240V, 50 amps.
K930-2 TIG MODULE - Provides high frequency and shield-
ing gas control for AC and DC GTAW (TIG) welding applica-
tions. Its compact case is designed for easy carrying, com-
plete with a handle. High frequency bypass is built in
Requires K938-1 Contactor Kit, K936-4 Control Cable, and
K814 Arc Start Switch.
K938-1 CONTACTOR KIT - For use with TIG Module,
Provides a "cold" electrode until the triggering device (Arc
Start Switch) is pressed.
K936-4 CONTROL CABLE - Connects TIG Module to ZR-8.
K814 Arc START SWITCH - Attaches to the TIG torch for
convenient finger control.
K937-45 CONTROL CABLE EXTENSION - Allows TIG
Module to be operated at distances up to 200ft. from the
power source. Available in 45ft. (13.7m).
K939-1 DOCKING KIT - For Mounting the K930-2 TIG
Module on top of the ZR-8.
ZR-8
C-1
Includes one UL
Advertisement
Table of Contents
