Accessories; Optional Equipment - Red-D-Arc ZR-10 Operation Manual

C-1

OPTIONAL EQUIPMENT

K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR
SMALL WELDERS
For road, off-road and in-plant and yard towing.
(For highway use, consult applicable federal, state
and local laws regarding requirements for brakes,
lights, fenders, etc.).
Two-Wheel Undercarriage (K889-2) - For moving by
hand. Overall Width 29 in (.74m)
Caster for Undercarriage (K893-1) - Mounts to the
front of the K889-2 to allow easy movement on
smooth surfaces. Includes 6" diameter hard rubber
wheel and convenient toe-on, toe-off locking brake.
Canvas Cover (K886-1) - To protect the ZR-10 when
not in use. Made from attractive red canvas material
which is flame retardant, mildew resistant, and water
repellent.
Power Plug Kit (K802-N) - Provides four 115V plugs
rated at 20 amps each and one dual voltage, full KVA
plug rated at 115/230V, 50 amps. (For K1418-2 or
K1419-2 CSA machines and machines with GFCI
receptacles, use K802-R).
Power Plug Kit (K802-R) - Provides four 115V plugs
rated at 15 amps each and one dual voltage, full KVA
plug rated at 115/230V, 50 amps.
Accessory Kit (K710) - Includes 30 ft (9.1m) 3 AWG
electrode cable, 25 ft. (7.6m) 3 AWG work cable,
headshield with No. 12 filter, GC300 work clamp and
Cooltong® 300 electrode holder. Cables are rated at
225 amps, 40% duty cycle.
Remote Control Receptacle Kit (K892-1) - Includes
a 6-pin MS-type (Amphenol) receptacle and a local-
remote toggle switch that mounts in the case front.
Requires a Remote Control Option.
Remote Control (K857) - Consists of a control box
with 25 ft. (7.5m) of four conductor cable. Permits
remote adjustment of output voltage. (Requires
Remote Control Receptacle Kit to be mounted in
machine.)
Spark Arrester Kit (K894-1) - Includes a heavy
gauge steel, approved spark arrester and clamp for
easy mounting to muffler exhaust pipe.

ACCESSORIES

(Field Installed) GFCI Receptacle Kit (K1690-1) - Includes one UL
approved 115V ground fault circuit interrupter duplex
type receptacle with cover and installation instruc-
tions. Replaces the factory installed 115V duplex
receptacle. Each receptacle of each GFCI Duplex is
rated at 20 Amps, but the maximum total current from
each GFCI Duplex is limited to 20 Amps.
Two kits are required.
TIG Module (K930-2) - Provides high frequency and
shielding gas control for AC and DC GTAW (TIG)
welding applications. Its compact case is designed for
easy carrying, complete with a handle. High frequen-
cy bypass is built in.The K938-1 Contactor Kit must
be field installed in the TIG Module when used with a
ZR-10. Additionally, the K936-3 control cable is
required if remote control is used. If remote control is
not used the K936-4 control cable is required.
Foot Amptrol (K870)
Remote Control Cable (K936-3) - Control cable for
connecting the K930-2 TIG Module to a ZR-10
equipped with a K892-1 Remote Kit. 9-Socket to a
grounded 115 V plug and a 6 pin MS-connector.
(Contains circuits 2, 4, 31, 32, 75, 76, 77 and ground)
Remote Control Cable (K936-4) - Control cable for
connecting the K930-2 TIG Module to a ZR-10 not
equipped with a K892-1 Remote Kit. 9-Socket to a
grounded 115 V plug and a 6 pin MS-connector.
(Contains circuits 31, 32, and ground)
Docking Kit (K939-1) - For mounting the K930-1 TIG
Module unit on top of the ZR-10.
Remote Control Receptacle Kit (K892-1) - Required
when using a K930-1 TIG Module with and optional
amptrol.
Wire Feed:
LN-25 (K449) - Includes internal contactor for across
the arc operation (no control cable). Provides "cold"
electrode until gun trigger is pressed. Includes gas
solenoid. Remote control Receptacle Kit (K892-1) and
Remote voltage Control Kit (K444-1) are required for
voltage control at the feeder.
LN-7 - Contactor Kit (K240) is required.
Magnum Gun is required for gas-shielded welding.
Innershield Gun is required for gasless welding.
ZR-10
C-1