Page 1
KD-SX985 3 7 63 1515 0 SERVICE MANUAL CD RECEIVER KD-SX985 SOUND SOURCE L 13942296513 Area Suffix Other Areas Contents Safety precaution Flow of functional Preventing static electricity operation unit TOC read 1-20 Disassembly method Maintenance of laser pickup...
KD-SX985 3 7 63 1515 0 Safety precaution Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Please use enough caution not to see the beam directly or touch it in case of an adjustment or operation check.
Page 3
KD-SX985 3 7 63 1515 0 Preventing static electricity 1.Grounding to prevent damage by static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
Page 4
KD-SX985 3 7 63 1515 0 Disassembly method Removing the front panel unit (See Fig.1) Press the release switch and remove the front panel unit in the direction of the arrow. Front panel unit Removing the bottom cover Fig.1 (See Fig.2,3)
Page 5
KD-SX985 3 7 63 1515 0 Removing the heat sink (See Fig.6) Remove the four screws C attaching the heat sink on the left side of the body, and remove the heat sink. Heat sink Fig. 6 Removing the rear panel (See Fig.7 )
Page 6
KD-SX985 3 7 63 1515 0 Removing the MP3 board (See Fig.9) Prior to performing the following procedure, remove the top cover. Disconnect the wire from connector CN601on the MP3 board. Remove the five screws G and the MP3 board, CN601 releasing the joint f and g.
Page 7
KD-SX985 3 7 63 1515 0 Removing the (LCD & key) control switch board (See Fig.11 ~ 13) Prior to performing the following procedure, remove the front panel assembly. Remove the four screws I attaching the rear cover on the back of the front panel assembly.
Page 8
KD-SX985 < CD mechanism section > 3 7 63 1515 0 Removing the top cover (See Fig.1 and 2) Remove the two screws A on each side of the body. Top cover Joints a Lift the front side of the top cover and move the cover backward to release the two joints a.
Page 9
KD-SX985 3 7 63 1515 0 Removing the DET switch (See Fig.3 and 6) Extend the two tabs c of the feed sw. holder and pull out the switch. DET switch Unsolder the DET switch wire if necessary. Connector board Removing the chassis unit (See Fig.7 and 8)
Page 10
KD-SX985 3 7 63 1515 0 Removing the clamper assembly (See Fig.9 and 10) Prior to performing the following procedure, remove Clamper arm the top cover. spring Remove the clamper arm spring. Move the clamper assembly in the direction of the arrow to release the two joints d.
Page 11
KD-SX985 3 7 63 1515 0 Feed sw. holder Removing the pickup unit (See Fig.13 to 17) Joint f Prior to performing the following procedure, remove the top cover, the connector board and the chassis unit. Remove the screw D and pull out the pu.
Page 12
KD-SX985 3 7 63 1515 0 Removing the trigger arm (See Fig.18 and 19) Joint k Prior to performing the following procedure, remove the top cover, the connector board and the clamper unit. Trigger arm Turn the trigger arm in the direction of the arrow to release the joint k and pull out upward.
Page 13
KD-SX985 3 7 63 1515 0 Joint a' Link plate Joint r Removing the select arm (L) / select lock Select arm (L) Joint z Select arm (R) arm (See Fig.21 and 22) Select lock arm Prior to performing the following procedure, remove the top plate assembly.
Page 14
KD-SX985 3 7 63 1515 0 Joint a' Link plate Joint r Removing the select arm (R) / link plate Select arm (L) Joint z Select arm (R) (See Fig.21 and 22) Select lock arm Prior to performing the following procedure, remove the top plate assembly.
Page 15
KD-SX985 3 7 63 1515 0 Roller guide Removing the loading roller assembly Washer (See Fig.27 to 29) Loading roller assembly Prior to performing the following procedure, remove the clamper assembly and the top plate assembly. Roller guide Push inward the loading roller assembly on the gear side and detach it upward from the slot of the joint d’...
Page 16
KD-SX985 3 7 63 1515 0 Removing the loading gear (5), (6) and Loading gear bracket (7) (See Fig.31 and 32) Loading gear (6) Prior to performing the following procedure, remove the top cover, the chassis unit and the top plate assembly.
Page 17
KD-SX985 3 7 63 1515 0 Removing the gears (See Fig.33 to 36) Prior to performing the following procedure, remove the top cover, the chassis unit, the top plate assembly and the pickup unit. Slot j' Pull out the feed gear.
Page 18
KD-SX985 3 7 63 1515 0 Removing the turn table / spindle motor Turn table (See Fig.37 and 38) Prior to performing the following procedure, remove the top cover, the connector assembly and the chassis / clamper assembly. Remove the two screws K...
Page 19
KD-SX985 3 7 63 1515 0 Adjustment method Test instruments required adjustment Standard volume position 1.Digital oscilloscope (100MHz) Balance and Bass & Treble volume : Indication "0" 2.AM Standard signal generator Loudness : OFF 3.FM Standard signal generator 4.Stereo modulator 5.Electric voltmeter...
Page 20
KD-SX985 3 7 63 1515 0 Flow of functional operation unit TOC read Power ON When the laser diode correctly Set Function CD When the pickup correctly moves emits to the inner area of the disc Microprocessor $82 $81...
Page 21
KD-SX985 3 7 63 1515 0 Feed section Is the voltage output at Is the wiring for IC521 Is 3.3V present at IC561 IC521 pin "40" 5V or 0V? (56)~(64) correct? pin "20"? Check CD 8V Check the vicinity of and 5V.
Page 22
KD-SX985 3 7 63 1515 0 Maintenance of laser pickup (1) Cleaning the pickup lens Before you replace the pickup,please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired.
Page 23
KD-SX985 3 7 63 1515 0 Description of major ICs UPD784225GK-624 (IC501) : CPU 1.Pin layout 2.Pin function Symbol Function Function Symbol Connect to TEMP detecter Non use TEMP Connect to GND Non use Connect to GND Non use...
Page 24
KD-SX985 3 7 63 1515 0 UPD784215AGC175 (IC701) : Main micon 1.Pin layout 100 ~ 76 26 ~ 50 2.Pin functions(1/2) Pin No. Symbol Function CD RESET Reset output for CD sub-micon CD MUTING Muting request of CD sub-micon...
Page 25
KD-SX985 3 7 63 1515 0 2.Pin functions(2/2) Pin No. Symbol Function SD/ST Station detector or stereo indicator input MONO Monoral selection output H:Monoral 56~60 DETACH Detach detect input H:Detach SEEK/STOP Auto seek and stop selecting output FM/AM FM,AM band selecting output H:FM...
Page 26
KD-SX985 3 7 63 1515 0 TC94A14FA (IC621) : DSP & DAC 1.Terminal layout & block daiagram Clock generator 1-bit Servo control Digital equalizer Address automatic circuit adjustment circuit Data CLV servo slicer 16 k Synchronous guarantee L 13942296513...
Page 27
KD-SX985 3 7 63 1515 0 TC94A14FA Symbol Description EFM and PLCK phase difference signal output pin. TMAX TMAX detection result output pin. TMAX Detection Result TMAX Output Longer than fixed period "PV " Within fixed period "HiZ" Shorter than fixed period "AV...
Page 34
KD-SX985 3 7 63 1515 0 3.Pin function(2/2) TC94A02F-005 Pin No. Symbol Function External SRAM data input/output 4 terminal Digital power supply (2.5V) terminal External SRAM data input/output 5 terminal External SRAM data input/output 6 terminal External SRAM data input/output 7 terminal...
Page 35
KD-SX985 3 7 63 1515 0 BR24C01AFV-W-X (IC502) : EEPROM 1.Pin layout 2.Block diagram 1kbit EEPROM ARRAY 8bit 7bit SLAVE/WORD ADDRESS DATA 7bit ADDRESS REGISTER DECODER REGISTER START STOP CONTROL LOGIC L 13942296513 HIGH VOLTAGE GEN. Vcc LEVEL DETECT 3.Pin function...
Page 36
KD-SX985 3 7 63 1515 0 BR24C16F-X (IC771) : EEPROM 1. Pin layout 2. Pin function Symbol I/O Function Power supply. A0,A1,A2 No use connect to GND. Serial clock input. Serial data I/O of slave and ward address. Write protect terminal.
Page 38
KD-SX985 3 7 63 1515 0 HD74HC126FP-X (IC801) : Buffer 1.Terminal layout 3.Pin function Input Output Note) H:High level L:Low level X:Irrelevant Z:Off(High-impedance) State a 3-state input 2.Block diagram Output Input L 13942296513 Output Sample as Load Circuit 1...
Page 39
KD-SX985 3 7 63 1515 0 HD74HCT126T-X (IC503) : Buffer 1.Terminal layout 3.Pin function OUTPUT INPUT H : High level L : Low level X : Irrelevant Off (Hhigh-impedance)state of a 3-stage output 2.Block diagram L 13942296513 u163 1-39...
Page 40
KD-SX985 3 7 63 1515 0 LA47503 (IC301) : Power amp 1. Pin layout 2. Block diagram Mute circuit Muting & Ripple ON Time control filter Circuit Stand by switch 3.Pin function Pin No. Symbol Function Header of IC...
Page 41
KD-SX985 3 7 63 1515 0 LC75873NW(IC601):LCD Driver 1.Pin layout 2.Block diagram VDD1 COMON SEGMENT DRIVER DRIVER VDD2 CLOCK SHIFT REGISTOR GENERATOR ADDRESS DETECTOR 3.Pin function Pin No. Pin name Description Segment outouts for displaying the display data S1/P1 TO S4/P4 79,80 transferred by serial data input.
Page 42
KD-SX985 3 7 63 1515 0 PCM1716E-X (IC571) : D/A converter 1. Pin layout 2. Block diagram Serial VoutL Low-pass Filter Input LBCK Mult-level EXTL 8X Oversampling DATA Delta-Sigma Digital Filter Low-pass VoutR Modulator Filter with ML/llS Function Controller...
Page 43
KD-SX985 3 7 63 1515 0 RPM7138-V4(IC602):Remote control receiver Limiter Comparator Detection crimp TDA7404D-X(IC161):Carradio signal processor 1.Terminal layout 2.Block diagram Mono Fader Mono Fader Mono Fader L 13942296513 Mono Fader Mono Fader Mono Fader Zero Cross Mono/Beep Beep Digital Control I C-Bus...
KD-SX985 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan 200206 (No.49731) http://www.xiaoyu163.com...
KD-SX985 3 7 63 1515 0 SCHEMATIC DIAGRAMS CD RECEIVER KD-SX985 CD-ROM No.SML200206 SOUND SOURCE L 13942296513 Area Suffix Other Areas Contents Block diagram Standard schematic diagrams Printed circuit boards 2-5,6 u163 No.49731 COPYRIGHT 2002 VICTOR COMPANY OF JAPAN, LTD.
KD-SX985 3 7 6 3 1 5 1 5 0 Block diagram CD Mechanism ENC 1,2 CD PICKUP UNIT MECHA. SWITCH VOLUME JOG SYSTEM EN601 SW1~ 3 CONTROLLER IC701 REMOCON SPINDLE/FEED /LOADING MOTOR REMOTE CONTROL PLL CE VOL CL...
Page 55
http://www.xiaoyu163.com 3 7 63 1515 0 < M E M O > L 13942296513 u163 http://www.xiaoyu163.com...
Page 56
KD-SX985 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT. 10-1,1Chome,Ohwatari-machi,Maebashi-city,371-8543,Japan 200206 (No.49731) http://www.xiaoyu163.com...
KD-SX985 3 7 63 1515 0 PARTS LIST [ KD-SX985 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix L 13942296513 U --------------------- Other Areas - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 CD mechanism assembly and parts list (Block No.MB)
Page 58
KD-SX985 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 59
KD-SX985 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Q'ty Description Parts number Parts name Area ------------ CD MECHA GE10043-001A TOP CHASSIS GE40135-001A EARTH PLATE GE30568-003A HEAT SINK GE30393-001A BOTTOM COVER INSULATOR FSMA3005-001 SCREW...
Page 60
KD-SX985 3 7 63 1515 0 Parts list (General assembly) Block No. M1MM Item Parts number Parts name Q'ty Description Area VKW3001-330 COMP.SPRING 1 FOR DETACH BUTTON GE10042-001A REAR COVER FSYH4036-078 SHEET 1 REAR COVER VKZ4777-001 MINI SCREW 3 FRONT+REAR...
Page 61
KD-SX985 3 7 63 1515 0 CD mechanism assembly and parts list Block No. TN-2001-1003 Grease TNG-87 L 13942296513 u163 http://www.xiaoyu163.com...
Page 62
KD-SX985 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Q'ty Description Parts number Parts name Area 30320101T FRAME 30320102T TOP COVER 30320109T DAMPER F 30320110T DAMPER R 303205501T CHASSIS RIVET A CHANGE P.RVT A...
Page 63
KD-SX985 3 7 63 1515 0 Parts list (CD mechanism) Block No. MBMM Item Parts number Parts name Q'ty Description Area 30321103T LOADING GEAR 3 30321104T LOADING GEAR 4 30321105T LOADING GEAR 5 LOADING GEAR 6 30321106T LOADING GEAR 7...
Page 64
KD-SX985 3 7 63 1515 0 Block No. 01 Electrical parts list (Main board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area BZ841 QAN0002-001Z BUZZER C 262 QERF1CM-106Z E CAPACITOR 10MF 20% 16V...
Page 65
KD-SX985 3 7 63 1515 0 Block No. 01 Electrical parts list (Main board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 722 NCB31HK-103X C CAPACITOR D 709 UDZS5.6B-X Z DIODE C 724...
Page 66
KD-SX985 3 7 63 1515 0 Block No. 01 Electrical parts list (Main board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area Q 977 2SA1037AK/RS/-X TRANSISTOR R 311 NRSA63J-823X MG RESISTOR NRS181J-120X MG RESISTOR...
Page 67
KD-SX985 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Remarks Parts number Parts name Area R 748 NRSA63J-472X MG RESISTOR R 749 NRSA63J-472X MG RESISTOR R 750 NRSA63J-103X MG RESISTOR R 751 NRSA63J-103X...
Page 68
KD-SX985 3 7 63 1515 0 Block No. 02 Electrical parts list (Mecha coutrol board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 501 NCB31AK-474X C CAPACITOR C 627 NCB31HK-103X C CAPACITOR...
Page 69
KD-SX985 3 7 63 1515 0 Block No. 02 Electrical parts list (Mecha coutrol board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area IC504 NJU7241F33-X R 542 NRSA63J-101X MG RESISTOR IC571 PCM1716E-X R 543...
Page 70
KD-SX985 3 7 63 1515 0 Electrical parts list (Mecha coutrol board) Block No. 02 Item Parts number Parts name Remarks Area R 626 NRSA63J-474X MG RESISTOR R 627 NRSA63J-103X MG RESISTOR R 628 NRSA63J-225X MG RESISTOR R 629...
Page 71
KD-SX985 3 7 63 1515 0 Block No. 03 Electrical parts list (Front board) Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 601 NBE20JM-475X TS E CAPACITOR R 623 NRSA02J-182X MG RESISTOR...
Page 72
KD-SX985 3 7 63 1515 0 Packing materials and accessories parts list Block No. Block No. A1~A3 L 13942296513 KIT:A4~A8 u163 3-16 http://www.xiaoyu163.com...
Page 73
KD-SX985 3 7 63 1515 0 Parts list (Packing) Block No. M3MM Item Description Parts number Parts name Q'ty Area FSPG4002-001 POLY BAG 1 FOR INST BOOK QPA00801205 POLY BAG 1 FOR SCREW KIT FSYH4036-068 SHEET 1 MIRAMA SHEET...