Yamaha DRX-1 Service Manual page 31

Error Nr Error String
71301 "Routing the audio on the Analogue Board
fails."
71302 "Invalid input."
71303 "Communication with Analogue Board fails"
71500 ""
71501 "Invalid slash version, default slash version is
set."
71502 "Setting the slash version on the Analogue
Board fails."
71503 "Communication with Analogue Board fails"
71600 "ApplicationVersion"
71601 "Can not find segment in FLASH ROM on the
Ana-logue Board"
71602 "Communication with Analogue Board fails"
71700 "DiagnosticsVersion"
71701 "Can not find segment in FLASH ROM on the
Ana-logue Board"
71702 "Communication with Analogue Board fails"
71800 "DownloadVersion"
71801 "Can not find segment in FLASH ROM on the
Ana-logue Board"
71802 "Communication with Analogue Board fails"
72300 ""
72000 ""
72001 "Adjusting BarGraphLevel failed"
72002 "Communication with Analogue Board fails"
72100 ""
72101 "Storing clock correction failed"
72102 "Value out of range : default value stored "
72103 "Invalid input."
72104 "Communication with Analogue Board fails"
72200 ""
72201 "Initialising the 1Hz signal on the Clock IC
failed"
72202 "Communication with Analogue Board fails"
72301 "Clearing the NVRAM on the Analogue Board
fails"
72302 "Communication with Analogue Board fails"
72400 "segment checksum is : checksum which is
cor-rect"" for every segment"
72401 "segment could not be found"" or ""segment
check-sum is : checksumC ,however it should
be : check-sumE"" for every segment"
72402 "Communication with Analogue Board fails"
72900 "Date received"
72901 "Data returned"
72902 "Communication on I2C-bus failed on the
Ana-logue Board fails."
72903 "Communication with Analogue Board fails"
73000 ""
73001 "Storing the external presets on the Analogue
Board fails"
Error Nr Error String
73002 "Communication with Analogue Board fails"
73100 "0xslashversion"" where slashversion is the
slash version read from the analogue board"
73101 "Error while reading out slash version."
73102 "I2C Write error."
73103 "I2C Read error."
73104 "Communication with Analogue Board fails"
73200 ""
73201 "Storing the Reference Voltage for the Tuner
failed"
73202 "Invalid input."
73203 "Communication with Analogue Board fails"
80000 "The DVIO module is present in the system."
80001 "The DVIO module is not present in the
system."
80100 "The DVIO module has been reset OK."
80101 "The DVIO module is not present in the
system."
80102 "The DVIO module could not be reset."
80103 "Could not initialise I2C before Reset."
80200 "The accessibility of the DVIO module is OK."
80201 "The DVIO board is not present in this DVDR."
80202 "Could not initialise I2C."
80203 "Unable to reset the DVIO module."
80204 "Unable to receive the reset indication from
the DVIO module."
80205 "Unable to send the configuration to the DVIO
module."
80206 "Unable to download the chip ID to the DVIO
mod-ule."
80207 "Unable to set the mode of the DVIO module
to IDLE."
80208 " S o f t w a r e E r r o r
HandleStateAwaitin-gReply!!"
80209 "Maximal number of retries reached by
HandleS-tateSending!!"
80210 "Maximal number of retries (NACKs) reached
(HandleStateSending)"
80211 " W e t r i e d t o r e c e i v e a r e p l y f o r
DVIO_MAX_RETRIES_ACKREPLY times !!"
80212 " W e t r i e d t o r e c e i v e a r e p l y f o r
DVIO_MAX_RETRIES_REPLY times !!"
80213 " W e t r i e d t o r e c e i v e a n A c k f o r
DVIO_MAX_RETRIES_ACK times!!"
80214 "VSM UART error timeout transmitting
command"
80215 "VSM UART error timeout receiving reply"
80216 "VSM UART frame error occurred receiving
from DVIO board"
80217 "VSM UART parity error occurred receiving
from DVIO board"
80218 "The confirmation/indication from the DVIO
module is invalid."
DRX-1
i n f u n c t i o n
31