Wiring Diagram - Daikin RZQS71D7V1B Technical Data Manual

8

Wiring diagram

8 - 1 Wiring diagram
RZQS71DV1
1
8
RZQS100-140DV1
27
• Outdoor Units • R-410A • RZQS-DV1
Indoor
El. comp. Assy
Position of elements
Position of
compressor
terminal
(Back)
Indoor
El. comp. Assy
Position of elements
Position of
compressor
terminal
Wire entrance
(Back)
• Split Sky Air • Outdoor Units
Outdoor
ON
OFF
(Note 4)
Notes:
1. This wiring diagram only applies to the outdoor unit
2. L: Live, N: Neutral, : Field wiring
3. : Terminal strip
: Protective earth (screw)
: Noiseless earth
4. Refer to the option manual, for connecting wiring to x6A.
5. Refer to the ''Wiring diagram sticker'' (on back of front plate) on how to use BS1∼ BS4
and DS1 switch.
6. Do not operate the unit by short-circuiting protection device S1PH
(Front)
7. Colours: WHT: White / RED: Red / BLU: Blue / ORG: Orange
BRN: Brown / GRN: Green / YLW: Yellow
8. Confirm the method of setting the selector switches (DS1) by service manual.
Factory setting of all switches: ''OFF''.
Outdoor
ON
OFF
(Note 4)
Notes:
1. This wiring diagram only applies to the outdoor unit
2. L: Live, N: Neutral, : Field wiring
3. : Terminal strip
: Protective earth (screw)
: Noiseless earth
4. Refer to the option manual, for connecting wiring to x6A.
5. Refer to the ''Wiring diagram sticker'' (on back of front plate) on how to use BS1∼ BS4
and DS1 switch.
6. Do not operate the unit by short-circuiting protection device S1PH
(Front)
7. Colours: WHT: White / RED: Red / BLU: Blue / ORG: Orange
BRN: Brown / GRN: Green / YLW: Yellow
8. Confirm the method of setting the selector switches (DS1) by service manual.
Factory setting of all switches: ''OFF''.
A1P : Printed circuit board (Main)
A2P : Printed circuit board (Inverter)
BS1∼BS4 : Push button switch
C1∼C3 : Capacitor
DS1 : Dip switch
F1U : Fuse (T 6.3A / 250V)
F6U : Fuse (T 3.15A / 250V)
H1P∼7P (A2P) : Light emitting diode (service monitor orange)
HAP (A1P) : Light emitting diode (service monitor green)
K1R : Magnetic relay (Y1S)
K10R : Magnetic relay
K11R : Magnetic relay
L1R : Reactor
M1C : Motor (compressor)
M1F : Motor (fan)
PS : Switching power supply
Q1DI : Field earth leakage breaker (30mA)
R1 : Resistor
R2 : Resistor
R1T : Thermistor (air)
R2T : Thermistor (discharge)
R3T : Thermistor (Suction)
R4T : Thermistor (Heat exchanger)
R5T : Thermistor (Thermistor (heat exchanger middle))
R6T : Thermistor (liquid)
R10T : Thermistor (fin)
RC : Signal receiver circuit
S1NPH : Pressure sensor
S1PH : Pressure switch (High)
TC : Signal transmission circuit
V1R : Power module
V2R,V3R : Diode module
V1T : IGBT
X1M : Terminal strip (Power supply)
Y1E : Electronic expansion valve
Y1S : Solenoid valve (4 way valve)
Z1C : Noise filter (ferrite core)
Z1F∼Z4F : Noise filter
: Connector : Connection
: Relay connector
: Terminal
2TW30466-1B
A1P : Printed circuit board (Main)
A2P : Printed circuit board (Inverter)
A3P : Printed circuit board (Noise filter)
A4P : Printed circuit board
BS1∼BS4 : Push button switch
C1∼C4 : Capacitor
DS1 : Dip switch
E1HC : Crankcase heater
F1U, F3U, F4U : Fuse (T 6.3A / 250V)
F6U : Fuse (T 5,0A / 250V)
H1P∼7P (A2P) : Light emitting diode (service monitor orange)
(H2P) Prepare, Test --------- Flickering
Malfunction Detection -- Light up
HAP (A1P) : Light emitting diode (service monitor green)
K1R : Magnetic relay (Y1S)
K4R : Magnetic relay (E1HC)
K10R : Magnetic relay
K11R : Magnetic relay
L1R : Reactor
M1C : Motor (compressor)
M1F : Motor (fan) (upper)
M2F : Motor (fan) (lower)
PS : Switching power supply
Q1DI : Field earth leakage breaker (30mA)
R1 : Resistor
R2 : Resistor
R1T : Thermistor (air)
R2T : Thermistor (discharge)
R3T : Thermistor (Suction)
R4T : Thermistor (Heat exchanger)
R5T : Thermistor (Thermistor (heat exchanger middle))
R6T : Thermistor (liquid)
R10T : Thermistor (fin)
RC : Signal receiver circuit
S1NPH : Pressure sensor
S1PH : Pressure switch (High)
TC : Signal transmission circuit
V1R : Power module
V2R,V3R : Diode module
V1T : IGBT
X1M : Terminal strip (Power supply)
Y1E : Electronic expansion valve
Y1S : Solenoid valve (4 way valve)
Z1C : Noise filter (ferrite core)
Z1F∼Z4F : Noise filter
: Connector : Connection
: Relay connector
: Terminal
2TW29166-2