1. Package Content Thank you for purchasing PLANET Layer 2 Managed Switch, WGSW-28040 series. Terms of “Managed Switch” means the Switches mentioned titled in the cover page of this Quick installation guide, i.e. WGSW-28040 / WGSW-28040P Open the box of the Managed Switch and carefully unpack it. The box should...
2. Requirements Workstations of subscribers running Windows XP/2003/Vista/7/2008, MAC OS9 or later, Linux, UNIX or other platform compatible with TCP/IP protocols. Workstation installed with Ethernet NIC (Network Interface Card) Serial Port connect (Terminal) Above PC with COM Port (DB9) Ethernet Port connect ...
115200,8,n,1 Serial Port In the terminal setup steps below, this Quick Installation Guide use WGSW-28040 as the example. However, the steps for WGSW- 28040P are similar. Note A terminal program is required to make the software connection to the WGSW Managed Switch.
Username: admin Password: admin 1. On “Username” & “Password” prompt, enter “admin”. 2. On “WGSW-28040>” prompt, enter “enable”. 3. On “Username” & “Password” prompt, enter “admin”. Figure 4-1: WGSW Managed Switch Console Login screen 1. For security reason, please change and memorize the new pass- word after this first setup.
Show the current IP address 1. On "WGSW-28040#” prompt, enter “config”. 2. On "WGSW-28040 (config)#” prompt, enter “show ip”. 3. The screen displays the current IP address, Subnet Mask and Gateway. As show in Figure 5-1.
Page 8
Configure IP address 4. On “WGSW-28040(config)#” prompt, enter the following command and press <Enter>. As show in Figure 5-2. WGSW-28040(config)# ip address 192.168.1.100 255.255.255.0 WGSW-28040(config)# ip default-gateway 192.168.1.254 The previous command would apply the follow settings for the Switch.
FLASH by write command or copy running-config startup-config command, so that the running configuration sequence becomes the start up configuration file, which is called configuration save. 1. On “WGSW-28040(config)#” prompt, enter “copy running-config startup- config”. As show in Figure 6-1. Figure 6-1: Save the Configuration screen...
7. Start Web Management The following shows how to start up the Web Management of the WGSW Managed Switch. Note the WGSW Managed Switch is configured through an Ethernet connection, please make sure the manager PC must be set on the same IP subnet address.
Page 11
Login the Managed Switch 1. Use Internet Explorer above browser, enter address http://192.168.0.100 (the factory-default IP address or that you have just changed in console) to access the Web interface. 2. When the following dialog box appears, please enter the default username and password “admin”...
Page 12
3. After entering the password, the main screen appears as Figure 7-3. The following screen based on WGSW-28040 for WGSW-28040P the display will be the same for WGSW-28040. Note Figure 7-3: Web Main Screen of WGSW Managed Switch 4. The Switch Menu on the left of the Web page let you access all the commands and statistics the Switch provides.
Save Configuration In switch, the running configuration file stores in the RAM. In the current version, the running configuration sequence running-config can be saved from the RAM to FLASH by write command or copy running-config startup-config command, so that the running configuration sequence becomes the start up configuration file, which is called configuration save.
Customer Support Thank you for purchase PLANET products. You can browse our online FAQ resource at the PLANET website first to check if it could solve you issue. If you need more support information, please contact PLANET switch support team. PLANET online FAQ : http://www.planet.com.tw/en/support/faq.php?type=1 Switch support team mail address :...