1. Manuals
  2. Brands
  3. ICRealtime Manuals
  4. Security Camera
  5. F Series
  6. User manual

ICRealtime F Series User Manual

Hide thumbs Also See for F Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
Megapixel Indoor Network Camera User's Manual
Version 1.0.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the F Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ICRealtime F Series

Summary of Contents for ICRealtime F Series

  • Page 1 Megapixel Indoor Network Camera User’s Manual Version 1.0.1...
  • Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!

  • Page 3: Important Safeguards And Warnings

    Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect two power supplying sources to the device at the same time;...
  • Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.

  • Page 5: Table Of Contents

    Table of Contents General Introduction ......................1 Overview ........................1 Feature ........................1 Specifications ......................2 1.3.1 Performance ...................... 2 Framework ..........................5 Rear Panel ........................ 5 Side Panel......................... 8 Front Panel ....................... 9 Bidirectional talk ....................... 9 2.4.1 Device-end to PC ....................9 2.4.2 PC to the Device-end ..................
  • Page 6 Operation ........................ 17 Web Operation ........................19 Network Connection....................19 Login and Main Interface ..................19 FAQ ............................21 Appendix Toxic or Hazardous Materials or Elements ............. 22...

  • Page 7: General Introduction

    1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts audio video data collection, transmission, storage together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology and PCM, G.711a/u audio compression technology, which maximally guarantees the audio and video quality.

  • Page 8: Specifications

    Do not connect two power supplying sources to the device at the same time; it may result in device damage!  Support Power over Ethernet (PoE). Conform to the IEEE802.3af standard.  Connect the device to the switcher or the router that supports the PoE function to realize the network power supply.
  • Page 9 H.264:32Kbps-8192Kbps, adjustable H.264:32Kbps-8192Kbps, adjustable MJPEG: 32~12288Kb/s, adjustable MJPEG: 32~16384Kb/s, adjustable Video Bit Rate and bit rate is adjustable. and bit rate is adjustable. Support customized setup. Support customized setup. Flip Support Mirror Support Snapshot Max 1f/s snapshot. File extension name is JPEG Privacy Mask Each channel supports max 4 privacy mask zones Video Setup...
  • Page 10 Weight 650g Installation Support various installation modes(Enclosure and bracket are optional)

  • Page 11: Framework

    2 Framework 2.1 Rear Panel This series network camera rear panel is shown as below. See Figure 2-1. Figure 2-1 Rear panel Note: Picture in this chapter is for reference only and actual rear panel may vary. Please refer to the following sheet for detail information. Interface Name Connector Function...
  • Page 12  STATUS Red light System boot up- Indication Light red light is on  System upgrades-red light flashes  System resets- red light flashes.  Green light Normal working status-green light is on.  Display record status: Record- green light flashes.
  • Page 13 RS232 port RS232_RX，RS232 receive end. RS232_TX，RS232 COM send out end. RS232 ground end IR light port External IR light signal control port. RESET RESET button Restore factory default setup. When system is running normally, press the RESET button for at least 5 seconds, system can restore factory default setup.

  • Page 14: Side Panel

    Micro SD Micro SD card port Connect to Micro SD card. Note  When you install the Micro SD card, please make sure current card is not in write mode and then you can install it to the camera.  When you remove the Micro SD card, please...

  • Page 15: Front Panel

    Figure 2-2 Side panel 2.3 Front Panel Please refer to the following interface for the front panel information. The unit is mm. See Figure 2-3. Figure 2-3 Front panel 2.4 Bidirectional talk 2.4.1 Device-end to PC Device Connection Please connect the speaker or the MIC to the audio input port in the device rear panel. Then connect the earphone to the audio output port in the PC.

  • Page 16: Pc To The Device-End

    2.4.2 PC to the Device-end Device Connection Connect the speaker or the MIC to the audio input port in the PC and then connect the earphone to the audio output port in the device rear panel. Login the Web and then click the Audio button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the audio talk function.

  • Page 17: Ir Light Connection

    Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of the alarm input port. When the input signal is connected to the 3.3V or is idle, the device collects the logic “1”. When the input signal is grounded, the device collects the logic “0”. Figure 2-5 Alarm input Please refer to the following figure for alarm output information.
  • Page 18 Figure 2-7 IR light connection...

  • Page 19: Installation

    3 Installation 3.1 Lens Installation 3.1.1 Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation. The interface is shown as in Figure 3-1.  Remove the CCD protection cap of the device, and then line up the lens to the proper installation position.

  • Page 20: Remove Lens

    and check the video is clear or not. If you cannot see the clear video, you can adjust via the flange-back.  After you completed the focus setup, use the slotted screwdriver to fix the screw firmly. Fasten the focusing ring. Now the installation completed. See Figure 3-2.

  • Page 21: Remove

    Figure 3-4 Micro SD card installation 3.2.2 Remove Please see Figure 3-5 to lightly press Micro SD card and it will automatically eject. Figure 3-5 Remove Micro SD card 3.3 I/O Port Install Cable Please follow the steps listed below to install the cable. See Figure 3-6. Use the small slotted screwdriver to press the corresponding button of cable groove.
  • Page 22 Figure 3-6 I/O port...

  • Page 23: Quick Configuration Tool

    4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”...
  • Page 24 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set. In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface.

  • Page 25: Web Operation

    5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ...
  • Page 26 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...

  • Page 27: Faq

    6 FAQ I can not boot up Please click RESET button for at least five seconds to restore factory default setup. the device or can not control the device. Micro SD card hot Before draw out SD card, please stop record or snapshot first and swap then wait for at least 15 seconds to remove the SD card.

  • Page 28: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Case ○ ○ ○ ○ ○ ○ Wire and Cable Packing ○...

Table of Contents