Adjusting Riving Knife - Makita LH1040 Original Instruction Manual

surface of the blade matches the direction of the arrow
on the blade case. Install the outer flange and hex bolt,
and then use the socket wrench to tighten the hex bolt
(left-handed) securely counterclockwise while pressing
the shaft lock.
Fig.18
Fig.19
NOTE:
When installing a saw blade, be sure to insert it
•
from the outside of the blade guard B at first and
then raise it so that the blade is finally placed in the
blade guard B.
For all countries other than European countries
Fig.20
CAUTION:
The silver ring 25.4 mm in outer diameter is
•
factory-installed onto the spindle. The black ring 25
mm in outer diameter is included as standard
equipment. Before mounting the blade onto the
spindle, always be sure that the correct ring for the
arbor hole of the blade you intend to use is
installed onto the spindle.
For European countries
CAUTION:
The ring 30
•
factory-installed between the inner and outer
flanges.
Return the lower blade guard A and center cover to its
original position. Then tighten the hex bolt clockwise to
secure the center cover. Raise the blade guard B as far
as it will go and tighten the clamping screw firmly while
holding it in the raised position. Lower the handle to
make sure that the lower blade guards move properly.
Make sure shaft lock has released spindle before
making cut.

Adjusting riving knife

Fig.21
Before adjusting the riving knife, loosen the two levers
by turning counterclockwise and press the top table on
the right side nearby the riving knife to its lowered
position. Then secure
re-tightening the two levers as shown in the figure.
There must be a clearance of about 4 - 5 mm between
the riving knife and the blade teeth. Adjust the riving
knife accordingly by
counterclockwise with the hex socket wrench and
measuring the distance. Tighten the hex bolts securely,
and then check to see that the top blade guard works
smoothly before cutting.
Fig.22
The riving knife has been installed before shipment from
the factory so that the blade and riving knife are in a
straight line.
Fig.23
mm in outer diameter
the top table by
loosening two hex
CAUTION:
If the blade and riving knife are not aligned properly,
•
a dangerous pinching condition may result during
operation. Make sure the riving knife is positioned
between both outer ends of the blade teeth when
viewing from the top. You could suffer serious
personal injury while using the tool without a
properly aligned riving knife. If they are not aligned
for any reasons, always have Makita authorized
service center repair it.
Don't remove the riving knife.
•
Installing and adjusting rip fence
Fig.24
1. Install the rip fence on the table so that the rip
fence holder engages with the guide rail. Tighten
the clamping screw (B) of the rip fence firmly
clockwise.
2. Loosen the clamping screw (A).
3. Slide the rip fence and secure it so that the far end
from you of the rip fence is aligned with the point
at which the front edge of saw blade just appears
from top surface of the workpiece. The purpose of
this adjustment is to reduce risk of kick-back
toward operator that cut piece from the workpiece
is pinched between the saw blade and rip fence
and finally pushed out toward operator. The line 3
is
varies by thickness of workpiece or the table level.
Adjust the position of the rip fence according to
the thickness of the workpiece.
After adjusting the rip fence, tighten the clamping
screw (A) firmly.
Fig.25
NOTE:
There are four patterns to position the rip fence as
•
shown in the figure. Rip fence has two slits on its
sides, one slit with an elevated fringe nearby on
the same side and the other without it. Use the
surface of rip fence with this fringe facing the
workpiece only when cutting off into a piece of a
thin workpiece.
Fig.26
firmly
NOTE:
To change the rip fence pattern, remove the rip
•
fence from the rip fence holder by loosening the
bolts
clamping screw (A) and change the facing of the
rip fence to the rip fence holder so that the rip
fence faces the rip fence holder according to your
work as shown in the figure.
Insert the square nut on the rip fence holder into
the back end of either slit of the rip fence so that
they fit as shown in the figure..
To change from the pattern A or B to the pattern C
or D, or in adverse case, remove the square nut,
washer and clamping screw (A) from the rip fence
12