Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Silk'n FaceFX DO105625B
Summary of Contents for Silk'n FaceFX DO105625B
-
Page 1: Instructions For Use
Instructions for Use DO105625B... - Page 2 Treating with Silk’n FaceFX for the First Time The skin should be, clean, dry and free of any powder, gel or cream. If necessary a light oil based serum may be applied thinly to the skin to help glide the device. Allow serum to absorb into the skin before treating.
-
Page 3: Table Of Contents
Table of Contents Before You Start............................4 What is Silk’n FaceFX?..........................4 Silk’n FaceFX device description......................4 Package contents.............................5 Safety with Silk’n FaceFX........................6 When to avoid using Silk’n FaceFX?....................6 Reducing the risk of injury..........................7 Possible side effects using FaceFX......................7 Protect your Silk’n FaceFX........................8 Skin Treatment the FaceFX Way...................9 The benefits of Silk’n FaceFX........................9 Silk’n FaceFX facial treatment areas....................9... -
Page 4: Before You Start
Before You Start Before using Silk’n FaceFX for the first time, please read this manual in its entirety. Pay particular attention to sections on device use procedures, device operation, and after-use procedures. What is Silk’n FaceFX? Silk’n FaceFX is a hand held light emitting diode (LED) device for facial treatments of periorbital wrinkles, reducing pore size and temporary improvement of the appearance of the skin. -
Page 5: Package Contents
G StandBy - indicator light Treatment surface System Error - indicator light On/off Switch Ready/Treatment - indicator light Indicators Panel Spare - indicator light Applicator Plug Adaptor The green Ready/Treatment - indicator light (K) illuminates when pressing the ON/OFF switch. The green StandBy - indicator light (G) illuminates when the device is turned off. -
Page 6: Safety With Silk'n Facefx
Safety with Silk’n FaceFX To protect your skin, a temperature sensor is embedded in the treatment tip of the Silk’n FaceFX. This sensor ensures the skin’ s surface will not exceed 41°C / 106°F. When to avoid using Silk’n FaceFX? Certain conditions may temporarily prevent the use of Silk’n FaceFX. -
Page 7: Reducing The Risk Of Injury
Reducing the risk of injury • Keep Silk’n FaceFX out of the reach of children. • Keep Silk’n FaceFX out of the reach of persons with reduced physical, sensory or mental capabilities. • Keep Silk’n FaceFX away from water! Do not use or store Silk’n FaceFX in a wet environment (e.g. -
Page 8: Protect Your Silk'n Facefx
• Skin Redness Your skin may become slightly red right after using FaceFX. This should disappear a few hours after treatment. Protect your Silk’n FaceFX • Store the device in a clean area free of dust. • Do not cover the ventilation slots during use. •... -
Page 9: Skin Treatment The Facefx Way
Skin Treatment the FaceFX Way The benefits of Silk’n FaceFX The outcome of using Silk’n FaceFX when following instructions correctly will be the reduction of facial fine lines, reducing pore size and improving the appearance of the face. Best results can be expected 3-7 weeks after completing the recommended course of treatment. -
Page 10: Plan Your Silk'n Facefx Treatment For Best Results
Plan your Silk’n FaceFX treatment for best results The efficiency of the results varies from person to person and according to the frequency of use. Some may see results sooner than others. A single FaceFX session usually takes 15-20 minutes in which you should gently glide the FaceFX applicator slowly over the desired treatment area. -
Page 11: Treating With Silk'n Facefx For The First Time
Treating with Silk’n FaceFX for the First Time The skin should be, clean, dry and free of any powder, gel or cream. If necessary a light oil based serum may be applied thinly to the skin to help glide the device. Allow serum to absorb into the skin before treating. -
Page 12: What To Expect When Treating With Silk'n Facefx
What to expect when treating with Silk’n FaceFX? During a Silk’n FaceFX session it is normal to experience and feel: A Sensation of Warmth – During the Silk’n FaceFX session you may feel slight warmth. This is normal and should disappear up to an hour after the session. -
Page 13: Maintenance Of Silk'n Facefx
Maintenance of Silk’n FaceFX Cleaning the Silk’n FaceFX After each session, it is recommended to clean your Silk’n FaceFX device: • Turn Silk’n FaceFX off by pressing the POWER ON/OFF SWITCH • Unplug Silk’n FaceFX from the electrical outlet • Allow cooling down of its TREATMENT SURFACE •... -
Page 14: Troubleshooting
Silk’n Customer Service Center for further support. Problem Possible Cause Solution The Adaptor is not Silk'n Clear does not Plug the adaptor to AC electrical outlet, and connected connect the Plug (E) to the Applicator work The Applicator is Contact your local Silk’n customer... -
Page 15: Customer Service
Customer Service For USA and Canada customers: For more information about Silk’n™ products please visit www.silkn.com. If your device is broken, damaged, in need of repair, or for any other user assistance, please contact Silk’n™ Customer Service: 1-877-DO-SILKN / 1-877-367-4556, contact@silkn.com International Customers: For more information about Silk’n products or to find a list of International Silk’n websites please visit www.silkn.eu or... -
Page 16: Specifications
Specifications Rated voltage (Adaptor) 100V - 240V Model: KSA24A1200150Hx 50Hz/60Hz Rated frequency (Adaptor) Rated (Adaptor) 12Vdc; 1500 mA Applied part Type BF Protecting rating IP30 (EN60529) Storage condition Temperature: -40°C to 70°C /-40°F to 158°F Relative humidity: 10% - 90% Atmospheric pressure: 500 to 1060 hPa Classified standard IEC 60601-1-2:2007... -
Page 17: Labeling
Labeling Degree of protection against electric shock: type BF applied part WEEE - Waste Electrical and Electronic Equipment CSA Mark CE Mark Keep dry Manufacturer Authorized Representative in the European Community Degree of protection against ingress water: IP30 ordinary This device is not suitable for use in the presence of flammable anesthetic mixture with air or with Oxygen or Nitrous Oxide. -
Page 18: Emc Testing Summary Results
EMC Testing Summary Results... - Page 19 Tavor Building, Shaar Yokneam POB 533 Yokneam 20692, ISRAEL tel. , fax +972-4-9097470 +972-4-9097471 info@silkn.com, contact@silkn.com www.silkn.com...