Panasonic KX-FT982LS-B Service Manual page 61

Code Function
573 Remote turn-on ring number set
580 TAM continuous tone detection
(KX-FT988 only)
590 FAX auto redial time set
591 FAX auto redial line disconnection time
set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
710 Memory clear except History data
717 Transmit speed select
718 Receive speed select
722 Redial tone detect
763 CNG detect time for friendly reception
773 DIS-DCS interval
774 T4 timer
784 Voice Prompt Test (KX-FT988 only)
815 Sensor test & Vox test (Vox test is available for KX-FT988 only.)
841 Digital SP-Phone check (KX-FT988 only)
845 Setting scanning density
852 Print test pattern
853 Top margin
874 DTMF ON time
875 DTMF OFF time
Set Value Effective
Range
× number of
00~99
rings
1: ON 1, 2
2: OFF
× number of
00~99
times
× second
001~999
1: OFF 1~3
2: ALL
3: AUTO
1: 75 msec 1~3
2: 500 msec
3: 1 sec
1: Detects at 1, 2
the 1st time
2: Detects at
the 2nd time
1: 5 % 1~4
2: 10 %
3: 15 %
4: 20 %
× -1 dBm
00~15
× -1 dBm
20~48
1: 9600 BPS 1~4
2: 7200 BPS
3: 4800 BPS
4: 2400 BPS
1: 9600 BPS 1~4
2: 7200 BPS
3: 4800 BPS
4: 2400 BPS
1: ON 1, 2
2: OFF
1: 10 sec 1~3
2: 20 sec
3: 30 sec
1: 500 msec 1, 2
2: 200 msec
× 100 msec
00~99
00~32 00~32
× mm
1~9
× 10 msec
06~20
× 10 msec
06~20
61
KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B
Default
10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
1 ON: Stops TAM operation when Dial tone, etc are
detected.
02 Selects the number of redial times during FAX commu-
nication (not including the first dial).
065 Sets the FAX redial interval during FAX communication.
2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialing is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.86).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.88). Refer to Receive
Problem (P.87) and The unit can copy, but cannot
transmit/receive (P.88).
1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot transmit/receive (P.88). Refer to Sometime
there is a transmit problem (P.86) and The unit can
copy, but cannot transmit/receive (P.88).
2 Sets the number of acceptable error lines when the
FAX reconstructs the received data. Refer to Receive
Problem (P.87).
11 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.86) and Receive Prob-
lem (P.87).
42 Used when there is an error problem. Refer to The unit
can copy, but the transmission and reception image
are incorrect (P.91).
Refer to Memory Clear Specification (P.62).
1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.86) and The unit can copy, but the transmission
and reception image are incorrect (P.91).
1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.87) and The unit
can copy, but the transmission and reception image
are incorrect (P.91).
2 Sets the tone detection mode after redialing.
3 Selects the CNG detection tone of friendly reception.
2 This is similar to #594. The time interval from receiving
DIS to sending DCS can be changed to wait for the
echo canceler to recover.
00 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
See Test Mode (P.55).
See Test Mode (P.55).
See Digital Speakerphone (KX-FT988 only) (P.118).
08 Select scanning density when the code No.58 is set
"Normal". If you want darker, select smaller value. If you
want fainter, select larger value. Refer to Program
Mode Table (P.94).
See Test Mode (P.55).
5
10
10
Remarks
----------
----------
----------