Panasonic KX-FT982LS-B Service Manual page 60

KX-FT982LS-B / KX-FT984LS-B / KX-FT988LS-B
11.1.3. Service Function Table
Code Function
501 Pause time
503 Dial speed select
510 VOX time (KX-FT988 only)
511 VOX sensitivity (KX-FT988 only)
512 VOX mode Detection (KX-FT988 only) 1: A
514 Bell detection time
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
544 Document feed position
550 Memory Clear
551 Flash memory check
552 DTMF single tone test
553 Monitor on FAX communication select
554 Modem test
555 Scan test
556 Motor test
557 LED test
558 LCD test
559 Document jam detection select
560 Cutter selection
(KX-FT984/KX-FT988 only)
561 KEY test
562 Cutter test (KX-FT984/KX-FT988 only)
567 T0 timer
570 BREAK % select
571 ITS auto redial time set
572 ITS auto redial line disconnection time
set
Set Value Effective
Range
× 100 msec
001~600
1: 10 pps 1, 2
2: 20 pps
1:6 sec 1, 2
2:4 sec
1: High 1, 2
2: Low
1, 2
2: B
× 100 msec
1~9
1: 2100 Hz 1, 2
2: 1100 Hz
1: ON 1, 2
2: OFF
1: ON 1, 2
2: OFF
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km 1~4
2: 1.8 km
3: 3.6 km
4: 7.2 km
× mm
1~9
1: ON 1, 2
2: OFF
1: OFF 1~3
2: PHASE B
3: ALL
1: ON 1, 2
2: OFF
1: ON 1, 2
2: OFF
× second
001~255
1: 61% 1, 2
2: 67%
× number of
00~99
times
× second
001~999
60
Default
030
1
1 Setting of the end of call confirmation VOX.
1 When the TAM (or EXT TAM) does not stop recording
the ICM because noise is detected on the telephone
line, change this setting to "LOW".
1
6
1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.88).
1 See Symptom/Countermeasure Table for long distance
and international calls in The unit can copy, but can-
not transmit/receive (P.88).
1 The resolution reverts to the default when transmission
is complete.
1 When the telephone station is far from the unit or recep-
tion cannot be performed correctly, adjust accordingly.
1 When the telephone station is far from the unit or trans-
mission cannot be performed correctly, adjust accord-
ingly.
5 When the ADF function is in correct, adjust the feed
position.
See Memory Clear Specification (P.62).
See Test Mode (P.55).
2 See Test Mode (P.55).
1 Sets whether to monitor the line signal with the unit's
speaker during FAX communication or not.
See Test Mode (P.55).
See Test Mode (P.55).
See Test Mode (P.55).
See Test Mode (P.55).
See Test Mode (P.55).
1 Sets whether or not to detect a paper jam. If a docu-
ment with a length longer than 600 mm is copied or
transmitted, the unit stops copying or transmitting as a
paper jamming because a document over 600 mm is
not normal. In the factory, transmitting or copying a doc-
ument longer than 600 mm is done as an aging test. In
this case, OFF is selected.
1 Turns off the cutter function.
See Test Mode (P.55).
See Test Mode (P.55).
046
2 Sets the % break of pulse dialing according PBX.
00 Selects the number of times that ITS is redialed (not
including the first dial).
065 Sets the interval of ITS redialing.
Remarks
----------
----------
----------
----------
----------