Roland PK-6 Owner's Manual page 25

MIDI Controller User Edit
Display Value
Not, FA (Start), FB (Conti-
Ctu
nue), FC (Stop), In1
(Intro1), In2 (Intro2), In3
(Intro3), In4 (Intro4), Mn1
(Main1), Mn2 (Main2),
Mn3 (Main3), Mn4
(Main4), Fu1 (Fill Up1),
Fu2 (Fill Up2), Fu3 (Fill
Up3), Fd1 (Fill Down1),
Fd2 (Fill Down2), Fd3 (Fill
Down3), En1 (Ending1),
En2 (Ending2), En3
(Ending3), En4 (Ending4),
Brm (Break Mute), Oin
(Old Intro), Oen (Old
Ending), Ofv (Old Fill To
Variation), OFo (Old Fill To
Original)
Using this parameter, you can assign the desired con-
trol functions to the PK-6's pedals. See also "MIDI
CONTROLLER mode" auf S. 16.
Proceed as follows:
(a) Press the [SHIFT] footswitch to activate Shift mode
(secondary footswitch functions).
The [SHIFT] indicator lights. The display shows"---".
(b) Press the [HOLD/PARAMETER] footswitch.
The [PARAMETER] indicator flashes.
(c) Press the [OCTAVER BASS/DOWN] or [PORTA-
MENTO/UP] footswitch to select the "CtU" parame-
ter.
(d) Press the [ENTER] pedal to confirm.
The display now shows "---" to signal that you need
to press a pedal.
(e) Press the pedal you want to assign a new function
to.
The display shows the function currently assigned to
that pedal.
(f) Press the [OCTAVER BASS/DOWN] or [PORTA-
MENTO/UP] footswitch to select the desired func-
tion (see the table above).
(g) If you want, repeat from step (e) to assign a new
function to the other pedals.
(h) When finished, press the [SHIFT] footswitch to exit
Parameter mode.
Drum User Edit
1~128
dru
This parameter allows you to select note numbers to
the pedals, which will be used in DRUM mode—but
only if you select the "drU" setting. See also "DRUM
mode" auf S. 15.
Proceed as follows:
(a) Press the [SHIFT] footswitch to activate Shift mode
Default
(secondary footswitch functions).
See
The [SHIFT] indicator lights. The display shows"---".
"MIDI
(b) Press the [HOLD/PARAMETER] footswitch.
CONT-
The [PARAMETER] indicator flashes.
ROLLER
(c) Press the [OCTAVER BASS/DOWN] or [PORTA-
mode" on
MENTO/UP] footswitch to select the "drU" parame-
page 16.
ter.
(d) Press the [ENTER] pedal to confirm.
The display now shows "---" to signal that you need
to press a pedal.
(e) Press the pedal you want to assign a note number
to.
The display shows the note number currently assig-
ned to that pedal.
(f) Press the [OCTAVER BASS/DOWN] or [PORTA-
MENTO/UP] footswitch to select the desired note
number (see the table above).
(g) If you want, repeat from step (e) to assign a new
note number to the other pedals.
(h) When finished, press the [SHIFT] footswitch to exit
Parameter mode.
Battery Status
bat
Refer to "Battery charge indication" auf S. 10.
Auto Off
Aof
This parameter allows you to specify how long the
PK-6 should wait before switching itself off while
you are not using it. If you don't want the power to
turn off automatically, select "Off".
Factory Reset
Refer to "Restoring the settings to
the factory condition (Factory Reset)"
auf S. 26.
MIDI Dump
Refer to "Archiving and restoring
your settings (MIDI Dump)" auf S. 26.
See
"DRUM
Write
mode" on
Refer to "Saving the settings (Write
page 15.
Function)" auf S. 23.
Dynamic MIDI Pedal PK-6
Parameter settings
0~100 –
(cannot be changed)
0ff, 10, 30, 240 240
FAC
dmp
Wri
r
25