Page 1
VMA43007-R.3780.A 作成承認印 配布許可印 サービス 計画課 M VMA43007(BLACK) REPAIR MANUAL Copyright c 2009 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !! Printed in Japan March 2009...
VMA43007-R.3780.A Disassembly WARNING There are high voltage parts inside. Be careful of this electric shock, when you remove the cover. You must discharge the main condenser according to the instruction of this repair manual after you remove the cover. Points to notice for Lead-free solder products ・...
VMA43007-R.3780.A Rear cover ・ Raise the flash unit (pop-up), and take out the two screws (#203). #203 ・ Take out the screw (#203). ・ Open the USB cover (#103), and take out the screw (#202). #103 #202 #203 ・ Take out the four screws (#201) and two screws (#202) #201 #202 #201...
VMA43007-R.3780.A ・ Take out the two screws (#203) and two screws (#204). #203 #204 ・ Remove the rear cover. ・ Remove the double-stick tape (#127) and then the monitor cover (#128) from the rear cover (#126). #126 #127 #128 Battery cover ・...
VMA43007-R.3780.A LCD unit ・ Remove the LCD unit (#125). (When removing this, be careful NOT to touch the condenser wire.) Condenser wire #125 Discharge of main condenser WARNING There are high voltage parts inside. Be careful of this electric shock, when you remove the cover.
VMA43007-R.3780.A LCD holder ・ Take out the screw (#206). ・ Remove the GND plate (#106). ・ Take out the two screws (#203) and screw (#207). #106 ・ Remove the LCD holder (#105). #105 #206 #207 #203 #203 Tripod base ・ Remove the tripod base (#104). #104 - D ・...
VMA43007-R.3780.A Front cover ・ Disconnect the FPC from the release button unit (#132). ・ Remove the two soldering bridges. ・ Unsolder the wires ([Red], [Black], [Gray], and [White]). ・ Remove the adhesive (C-8008B) from the wires ([Gray], [White], [Black], and [Brown]). ・...
Page 10
VMA43007-R.3780.A ・ Take out the two screws (#205). ・ Raise the flash unit (pop-up), and remove it upward. #205 ・ Remove the microphone (#131) wires ([Gray] and [Black]) from the guide. [Gray/Black] ・ Separate the front cover and the lens unit a little, and remove the USB cover (#103). #103 - D ・...
VMA43007-R.3780.A Battery holder ・ Take out the screw (#203). ・ Remove the wires ([Red] and [Black]) from the [Red/Black] guide. Guide #203 ・ Remove the battery holder. - D ・ L100 -...
Page 13
VMA43007-R.3780.A ・ Remove the condenser unit (#144). ・ Peel off the double stick tape (#145). #145 #144 ・ Unsolder the battery contact PCB (#153). ・ Take out the three screws (#206). ・ Remove the battery contact PCB (#153). (When removing this, be careful of the below hook.) ・...
Page 14
VMA43007-R.3780.A ・ Remove the holder strap (#150). #150 ・ Unhook at two places. Unhook here. - D11 ・ L100 -...
Page 15
VMA43007-R.3780.A ・ Remove the battery holder C (#146) from the battery holder A (#154). ・ Unhook the battery holder B (#151), and remove it in the same way. #146 #154 #151 ・ Remove the two battery contacts A (#152) from the battery holder A (#154). ・...
VMA43007-R.3780.A Release button unit ・ Take out the screw (#209). ・ Remove the release button unit (#132) from the front cover (#129). #209 #129 #132 - D1 ・ L100 -...
VMA43007-R.3780.A Main PCB ・ Disconnect the FPC from the lens barrel side. ・ Disconnect the three FPCs. ・ Take out the two screws (#206) and (#207). ・ Remove the main PCB (#142). #142 #207 #206 - D1 ・ L100 -...
VMA43007-R.3780.A Lens unit Caution: Be careful NEITHER to touch the whole area of the back (see below left picture) because there is the CCD stage on it, NOR to touch the extension area of the lens (see below right picture). Speaker ・...
Page 19
VMA43007-R.3780.A ・ Take out the two screws (#211). ・ Remove the speaker unit from the speaker holder (#139) . #211 #139 ・ Peel off the spacer (#138). ・ Remove the speaker (#137) and holder strap (#136) from the speaker cover (#135). #138 #137 #135...
VMA43007-R.3780.A Inner holder ・ While holding the inner holder (#133), take out the three screws (#212). #212 #133 #212 #212 ・ Remove the inner holder (#133) from the lens unit (#140). ・ Remove the three washers (#141). #141 #133 #141 #141 #140 LED PCB...
VMA43007-R.3780.A Flash unit ・ Take out the screw (#208). ・ Remove the pop up SW PCB (#112). #208 #112 ・ Take out the two screws (#204). ・ Push down the flash unit , and remove the flash top cover (#124). #204 #124 - D1 ・...
Page 22
VMA43007-R.3780.A ・ Peel off the spacer (#122). ・ With the flash unit being raised (popped-up), pull out the wires ([Brown], [Black], [Gray] and [White]) from the hole of the flash base (#113). ・ Remove the trigger coil (#119) and flash unit together. ・...
Page 23
VMA43007-R.3780.A ・ Pull out the shaft (#114). ・ Remove the spring (#110). #114 #110 ・ Remove the holder (#111). #111 ・ Remove the spring holder (#109). #109 - D0 ・ L100 -...
Page 24
VMA43007-R.3780.A ・ Peel off the double stick tape (#108). #108 ・ Remove the flash window (#116) from the flash bottom cover (#107). #116 #107 - D1 ・ L100 -...
VMA43007-R.3780.A Assembly Flash unit ・ Assemble the flash window (#116) into the flash-bottom-cover (#107), (with attention to the assembling direction). #116 #107 ・ Attach the double-stick tape (#108). #108 - A1 ・ L100 -...
Page 26
VMA43007-R.3780.A ・ Attach the spring holder (#109). #109 ・ Put the spring (#110) in the groove of the flash base (#113) (with attention to the hook's direction). ・ Insert the shaft (#114). #114 #110 Be careful of the hook's direction. ・...
Page 27
VMA43007-R.3780.A ・ Hook the spring (#110) as shown in the below " ", and mount the flash base (#113). □ ・ Push the flash base (#113) toward the under-cover, and insert the shaft (#115). flash bottom cover (#107) △(Revision) #113 #110 #115 △(Revision)
Page 28
VMA43007-R.3780.A ・ Mount the flash unit (#117) on the flash holder (#118) by fitting the three hooks as below. #118 #117 ・ Solder the trigger coil (#119). ・ Mount the trigger coil (#119) on the flash bottom cover (#113) . (#107) △(Revision) △(Addition)
Page 29
VMA43007-R.3780.A ・ Push down the flash unit, and mount the flash top cover (#124) by engaging the hooks. ・ Tighten the two screws (#204). #204 #124 ・ Mount the pop-up SW PCB (#112) by fitting with the boss. (When mounting this, put edge under " "...
VMA43007-R.3780.A LED PCB ・ Mount the LED PCB (#134) in the direction of the arrow. ・ Tighten the screw (#210) from the opposite direction. ・ Place the wires ([Gray] and [White]) among the guides (as shown the below left picture). ・...
Page 31
VMA43007-R.3780.A ・ Attach the two spacers (#157) based on the reference position. ・ Attach the three washers (#141). ・ Mount the inner holder (#133) on the lens unit (#140). Reference position #157 #141 [#141] attaching position Reference position #141 #141 #140 #157 #133...
VMA43007-R.3780.A Inner holder ・ While holding the inner holder (#133), tighten the three screws (#212) in the numeric order from ① to ③ . ① #212 #133 #212 ② #212 ③ Speaker ・ Mount the speaker (#137) and holder strap (#136) on the speaker cover (#135). ・...
Page 33
VMA43007-R.3780.A ・ Mount the speaker holder (#139) on the speaker unit by fitting with the boss. ・ Tighten the two screws (#211). Boss Be careful of the fit-in area. #211 #139 ・ Mount the speaker unit by engaging the two hooks. Speaker unit - A ・...
VMA43007-R.3780.A Main PCB ・ Mount the main PCB (#142) on the lens unit (#140) by fitting with the bosses. ・ Tighten the two screws (#206) and (#207). ・ Connect the three FPCs to the connectors. ・ Attach the spacer (#143) based on the reference position. #140 #142 #143...
VMA43007-R.3780.A Release button unit ・ Mount the release button unit (#132) on the front cover (#129). ・ Tighten the screw (#209). #209 #129 #132 Battery holder ・ Mount the two battery A contacts (#152) on the battery holder A (#154). ・...
Page 36
VMA43007-R.3780.A ・ Assemble the battery holder B (#151) and C (#146) into the battery holder A (#154). #146 #151 #154 ・ Attach the holder strap (#150) by fitting with the bosses. #150 Boss ・ Attach the battery contact PCB (#153) by fitting with the boss. ・...
Page 37
VMA43007-R.3780.A ・ Tighten the two screws (#203). ( the battery holes must be complete round as below.) #203 ・ Solder the battery contact PCB (#153). Solder ・ Attach the double-stick tape (#145) based on the reference position. ・ Place the condenser unit (#144) by fitting its PCB in the groove (see the below " ").
Page 38
VMA43007-R.3780.A ・ Arrange the wires as below. ・ Mount the battery holder on the front cover. (Caution must be exercised that the FPCs are not pinched in.) ・ Place the wires ([Red] and [Black]) behind the guide. ・ Tighten the screw (#203). [Red/Black] Guide #203...
VMA43007-R.3780.A Microphone ・ Attach the microphone (#131). ・ Arrange the wires ([Gray] and [Black]) as below. [Gray/Black] #131 Front cover ・ Mount the front cover. ・ Before mounting the above completely, attach the USB cover (#103). #103 - A1 ・ L100 -...
Page 40
VMA43007-R.3780.A ・ Tighten the two screws (#205). ・ Connect the FPC of the release button unit (#132). #205 #205 ・ Arrange the microphone (#131) wires ([Gray] and [Black]) as below. [Gray/Black] - A1 ・ L100 -...
Page 41
VMA43007-R.3780.A ・ Attach the two spacers (#114) based on the reference position (front cover side). ・ Mount the flash unit by raising it (pop-up). ・ Push down the flash unit, and tighten the two screws (#205). Reference position #114 Front cover side #205 ・...
VMA43007-R.3780.A Tripod base ・ Attach the Tripod base (#104). #104 LCD holder ・ Mount the LCD holder (#105). ・ Mount the GND plate (#106). ・ In the numeric order from ① to ④, tighten the screw (#206), two screws (#203) and the screw (#207). ・...
VMA43007-R.3780.A LCD unit ・ Connect the FPC to the connectors. ・ Mount the LCD unit (#125). #125 Battery cover ・ Mount the battery cover (#101). ・ Insert the shaft (#102). #102 #101 - A1 ・ L100 -...
VMA43007-R.3780.A Rear cover ・ Attach the double-stick tape (#127) and the monitor cover (#128) to the rear cover (#126) by aligning the below red lines. #127 #128 ・ Attach the two spacers (#156) and (#155) based on the reference position. ・...
Page 45
VMA43007-R.3780.A ・ In the numeric order from ① to ⑥, tighten the four screws (#201), and two screws (#202). #201 ⑤ ② ① #202 ④ ③ ⑥ #201 ・ Tighten the screw (#203). ・ Open the USB cover (#103) and tighten the screw (#202). #103 #202 #203...
VMA43007-R.3780.A ADJUSTMENT 1. Equipment PC, AC adapter (EH-62E) or AA-size battery (LR6 or FR6), USB cable (UC-E6), SD card (EH-67) △(Revision) 2. Servicing tools Pattern box (J63080), Color meter (J63095), Luminance meter (J63068), Adjustment collimator (J63090), Color viewer (J63070), DSC Calibration software Ver1.62b (J65098), SSIS calibration software Ver1.016 (J65123) 3.
Page 47
VMA43007-R.3780.A < Procedure for installation > ・Because this software is the self-extracting file, decompress the file before installing, and follow the next procedure. < Procedure for installing DSC calibration software > 1. Executing SetFolder.EXE" will create "C:¥DeskTopLauncher\C-DSC\DscCal" folder automatically. 2. Paste the file (DscCal.EXE) in the created folder. 3.
Page 48
VMA43007-R.3780.A < Caution for starting program > ・Before starting this program, close all the other running applications. Otherwise, the program may not run properly. When the inspection & adjustment software is started for the first time, the below window will be displayed on the monitor for typing in the user key.
Page 49
VMA43007-R.3780.A 4. Pattern box Before using the pattern box, turn its power on to carry out "aging" approx. 30 minutes: the color temperature must be adjusted to 3100 ± 20K by the color meter. When the pattern box is used and for a while even after the power turns off, the lamp and its surroundings are subject to high temperatures, so handle them with care.
Page 50
VMA43007-R.3780.A Calculating formula 168.89 × X Coefficient Ycd/ ㎡ 256 Coefficient X: Corresponding value by crossing K-1.3 and EV13 in the "Inspection report", which is an accessory of BM-3000 Y: Luminance e.g) 1365.2cd/ ㎡ 168.89× 900cd/ ㎡ 256 ref.
Page 51
VMA43007-R.3780.A 5. Adjustments required when parts are replaced ○ Adjustment is necessary. × Adjustment is not necessary. Lens adjust- CCD black / Adjustment item Shading Zoom Firmware Backlash ment white pixel central adjust- adjust- storage info update * calibration (1.5m & defect calibration ment...
Page 52
VMA43007-R.3780.A 6. Connecting camera to PC Connect the camera and PC through the USB cable. To the USB port USB Cable (UC-E6) Supply the power through AC adapter (EH-67) or AA - size battery (LR6 or FR6) 7. Adjustment item / order 1.
Page 53
・ The message that indicates the completion "Done" appears, then turn the camera OFF and remove the SD card. ・ Turn the camera ON to check "Firmware version". ・ Turn the camera OFF to end the procedure. Done COOLPIX L100 Ver . X.X Turn camera off to complete upgrade. Back Caution: After finishing the firmware update, be sure to perform the VR-MCU firmware update on the next page, too.
Page 54
VMA43007-R.3780.A 7-1-2. 【VR-MCU firmware update】 ・ Insert the SD card, in which the firmware was copied, into the camera. ・ Turn the camera ON. ・ Set the mode dial to "AUTO" and turn the camera OFF. ・ While pressing the "MENU" button and setting the zoom lever to "W", turn the camera ON. ・...
Page 55
VMA43007-R.3780.A 7-2.Backlash calibration Caution : "Gyro Gain Calibration" is not necessary △(Addition) ・ Connect the camera and PC through USB cable. ・ Turn the camera ON. ・ Place the camera in a regular position on a flat and steady board. ・...
Page 56
VMA43007-R.3780.A 7-3. Shading central calibration Caution: Set the luminance of the color viewer to "LV13" or equivalent. ・ Turn the camera ON. ・ At TELE-end zoom position, connect the camera and PC through USB cable. ・ At TELE-end zoom position, place the camera (front surface of lens) to the closest to the color viewer. ・...
Page 57
VMA43007-R.3780.A 7-4. Zoom adjustment ・ Connect the camera and PC through USB cable. ・ Turn the camera ON. ・ Start the DSC calibration software. ・ Select "Zoom Cal" from "Test" pulldown menu. ・ After the adjustment is completed, the result will appear. If the result is NOT in the range of the below stan- dard values, make readjustment .
Page 58
VMA43007-R.3780.A 7-5. Lens adjustment (1.5m) ・ Turn the camera on. ・ Set the mode dial to "AUTO" and "VR" to "OFF". ・ Prepare A3 or more size "Siemens star chart". [Enlarge the attached A4 size chart (of the last page of this adjustment chapter) with a copier and use it.] ・...
Page 59
VMA43007-R.3780.A [Siemens star chart] - A ・ L100 -...
Page 60
VMA43007-R.3780.A 7-6. Lens adjustment (Infinity) Caution: Be sure to finish the procedure of the lens adjustment (1.5m) before this adjustment. Use a tripod to set up the camera. ・ Turn the camera on. ・ Set the mode dial to "AUTO" and "VR" to "OFF". Camera Collimator (J63090) Connect the one side of the...
Page 61
VMA43007-R.3780.A 7-7. AWB adjustment ・ Turn the camera on. ・ At TELE-end zoom position, place the camera (front surface of lens) to the closest to the pattern box. Note) Do not allow outside light to enter in. ・ Connect the camera and PC through USB cable. ・...
Page 62
VMA43007-R.3780.A 7-8. CCD defective white (hot) pixel compensation against dark background ・ Connect the camera and PC through USB cable. ・ Turn the camera ON. ・ Start the DSC calibration software. ・ Select "CCD Defect" from "Test" pull-down menu. Click "Yes". ・...
Page 63
・ Click on the "Get" button in the USB storage window and check the USB storage data. VID:NIKON PID: DSC COOLPIX L100 Serial:XXXXXXXXXXXX ・ If the "Serial" in the USB storage data is different from the serial number of the camera bottom, enter the number of the camera’s bottom, and click "Set".
Page 64
VMA43007-R.3780.A 7-11. Language setting ・ Connect the camera and PC through USB cable. ・ Turn the camera ON. ・ Start the DSC calibration software. ・ Set Lang number" which enables to select either 2 Languages or 24 Languages " (Multilanguage). Caution) Select "2 Languages"...
VMA43007-R.3780.A 1. OUTLINE OF CIRCUIT DESCRIPTION Pin 1 1-1. CCD CIRCUIT DESCRIPTION 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. IC932 (MN34510PLJ-A) CCD imager IC901 (AN20118A) V driver IC905 (AD9971BCPZRL) CDS, AGC, A/D converter, Pin 19 H driver, vertical TG Fig.
Page 66
VMA43007-R.3780.A 3. IC901 (V Driver) 4. IC905 (H Driver, CDS, AGC and A/D converter) A V driver (IC901) is necessary in order to generate the clocks IC905 contains the functions of H driver, CDS, AGC and A/D (vertical transfer clock and electronic shutter clock) which converter.
Page 67
VMA43007-R.3780.A 1-2. CP1 CIRCUIT DESCRIPTION 1. Circuit Description 2. Outline of Operation 1-1. Signal processor (SIG) When the shutter opens, the serial signals (“take a picture” 1. Signal preprocessing block commands) from the 8-bit microprocessor is input to ASIC This block processes the raw data for the CCD. (IC101) and operation starts.
Page 68
VMA43007-R.3780.A 4. Lens drive block 4-1. Shutter drive The serial data signals (L_DATA) and (L_LATCH, SHUTTER, LENS_ST and L_SCLK) which are output from the ASIC (IC101) are used to drive regular current (SOUT1 and SOUT2) by the motor driver (IC951), and then mecha shutter is opened and closed.
Page 69
VMA43007-R.3780.A 1-3. PWA POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog +12 V (A) Power Output This is the main power circuit, and is comprised of the follow- +12 V (A) is output. Feedback for the +12 V (A) is provided to ing blocks.
Page 70
VMA43007-R.3780.A 1-4. SYA CIRCUIT DESCRIPTION 1. Configuration and Functions For the overall configuration of the SYA block diagram, refer to the block diagram. The SYA block centers around a 8-bit micropro- cessor (IC301), and controls camera system condition (mode). The 8-bit microprocessor handles the following functions. 1.
Page 71
VMA43007-R.3780.A NOT USED Command request (BOOT output) COMREQ/ZBOOT BACKUP_CTL Backup battery charge control NOT USED NOT USED BAT_OFF Battery OFF (removal) detection SREQ Serial communication request signal SHUTTER 2nd Shutter 2nd key detection ASIC directly HOTLINE RESET Backup reset detection XCIN Clock oscillation terminal for clock (32.768 kHz) Clock oscillation terminal for clock (32.768 kHz)
Page 72
VMA43007-R.3780.A 3. Key Operaiton For details of the key operation, refer to the instruction manual. SCAN SCAN RIGHT MODE TEST DETELE PW_TEST DOWN LEFT Table 4-2. Key Operation 4. Power Supply Control The 8-bit microprocessor controls the power supply for the overall system. The following is a description of how the power supply is turned on and off.
CL591 BATTERY JW302 JW602 AFLEDCA AFLEDCA JK501 JW601 JW301 AFLEDAN AFLEDAN W1-18400/SG28E-JNK TRANS TRIGGER TOP SW UNIT DC JACK JW304 JW652 GND BK JW651 JW303 POP UP POPUP RD FLASH SPEAKER REFLECTOR MODEL: COOLPIX L100 OVERALL WIRING - E ・ L100 -...
CL302 SKRMAGE010 SKRMAGE010 SKRMAGE010 AL3.2V AL3.2V PLAY TO STA CHGSEL CHGSEL VMONIT VMONIT Y1-18400/SG28E-JNK MODE PLAY LEFT POPUP_FL POPUP_FL MODEL: COOLPIX L100 SCAN IN CIRCUIT DIAGRAM: CP1 (SYA) SCAN OUT DELETE RIGHT MODE TEST PW_TEST DOWN LEFT - E1 ・ L100 -...
VMA43007-R.3780.A FUSE ARRANGEMENT (CP1 PCB / 4 pcs. are used. / All of them are positioned on SIDE-A.) (TB1 PCB / 1 pcs. are used. / All of them are positioned on SIDE-A.) ...
VMA43007-R.3780.A Inspection standards Items Judgment standard Remarks External view Gap/Difference in ・ General components Visual check height/level Gap: 0.2mm or less Difference in height: 0.15mm or less ・Bottom Gap: 0.2mm or less (except 0.3mm-gap designed) Difference in height: 0.3mm or less ・Gap of the right/left sections of pop-up flash: 0.4mm or less ・...
Page 93
VMA43007-R.3780.A Items Judgment standard Remarks Distance measurement Visual check ・ In the case of normal AF : Focus must be gained at the picture operation center. ・ In the case of the out-of-focus status :Focus must be gained at the following distance: 2m (Z00 - Z07), 5m (Z08 - Z10), 10m (Z11 - Z13) Shortest shooting...
Page 94
VMA43007-R.3780.A Items Judgment standard Remarks Shooting with Flash unit Light adjustment Standard reflector ・ Tele 0.5 - 4.5m accuracy ・ Wide 0.5 - 6.5m In the above range, +0.2± 0.5 EV or less (Shooting mode: AUTO, Speed light: Anytime flash) "Slow sync" ・...
Page 95
VMA43007-R.3780.A Items Judgment standard Remarks Shooting with Flash unit Light distribution Light distribution ・Full angle from right to left: features To left- 34° or more; to right- 34° or more; measuring equipment Relative to the central light quantity: -1.0Ev or less Flash meter ・Full angle from top to bottom: Protractor...
Page 96
VMA43007-R.3780.A Items Judgment standard Remarks Image quality Resolution in AF ・ Shooting conditions EIAJ chart Photoshop (Shoot EIAJ chart) Mode: AUTO Siemens chart Image quality: FINE Image size: 10M (3648×2736) White balance: AUTO ISO sensitivity setting : 64 Distortion control: OFF Exposure compensation: None Flash: Cancel VR (vibration reduction): OFF...
Page 97
VMA43007-R.3780.A Items Judgment standard Remarks Image quality Photoshop AF (15cm - 10m) ・The values must conform to the following in the entire zooming. Siemens chart Center horizontal/vertical: 900 TV lines ・Measure the TV resolution lines at center. ・Check each posture and the difference of zoom reciprocation. ・...
Page 99
VMA43007-R.3780.A Items Judgment standard Remarks Image quality Dust in photo Photoshop ・ There must not be an outstanding dust in a picture. CRT monitor ・ When the picture center (within the circle whose diameter is 80% of the short side) is Zone I and its outside is Zone II, light reduction against the periphery must be as below: Zone Ⅰ...
Page 100
VMA43007-R.3780.A Items Judgment standard Remarks Electric characteristics Consumption current ・ When card is not used: 0.2mA or less (when the power switch is Constant voltage power supply Stand-by (idle) current OFF) ・ When card is used: 0.2mA or less (when the power switch is Ammeter OFF) Dummy battery pack...
Page 101
VMA43007-R.3780.A 工具一覧表 Tool List ※ : 新規工具 ※ : New tool 工具番号 名 称 備 考 Tool No. Name Remarks J300 パターンボックス LV-1450DC 共通工具 Common Tool Pattern Box LV-1450DC J300A 交換用ハロゲンランプ (LV-1450DC 用 ) LV-1450DC 専用 Spare Halogen Lamp (For LV-1450DC) Exclusively for LV-1450DC J301 カラーメータ...