1. Manuals
  2. Brands
  3. EASEPAL Manuals
  4. Massager
  5. EC-385A
  6. Maintenance service manual

EASEPAL EC-385A Maintenance Service Manual

Hide thumbs
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

中国·厦门蒙发利科技有限公司
Xiamen Comfort Science & Technology Co.,Ltd
产 品 维 修 手 册
Maintenance Service Manual
产品型号/MODEL：
EC-385A
适用电压规格/
voltage
specification：220-240V
蒙发利集团·客服
By the Easepal`s Customer Service Dept.

Advertisement

Table of Contents
loading

Related Manuals for EASEPAL EC-385A

Summary of Contents for EASEPAL EC-385A

  • Page 1 中国·厦门蒙发利科技有限公司 Xiamen Comfort Science & Technology Co.,Ltd 产 品 维 修 手 册 Maintenance Service Manual 产品型号/MODEL： EC-385A 适用电压规格/ voltage specification：220-240V 蒙发利集团·客服 By the Easepal`s Customer Service Dept.
  • Page 2 一、产品故障列表 Trouble List 如下为 EC-385A 常见的故障现象及维修方法。 Common Troubles and Maintenance Methods are listed as below: 故障序 现象 描述 维修方法 号 NO phenomenon Description maintenance method 开机无功能 A.手控器无显示：LCD NO VISION ①、更换保险丝 No function ①、保险丝烧掉 Fuse melts Replace Fuse （ 电 源 盒 处 和 中 心 板 上 (in the ②、更换电源盒...
  • Page 3 宽中窄不能切换 ①、中心板宽度检测端子线材接触不 ①、②点将端子接插到位或是更换线 the Width 良。The terminals of Width 材 switchover Inspection on main PCB with wires Plug the terminals well or replace unchangeable were poorly connected the wires when meet problems of ②、机芯宽度检测板端子线材接触不 ①、② 良。The terminals of Width ③、更换宽度检测板 Inspection on mechanism with...
  • Page 4 No tapping The terminals on main PCB Plug the terminal well and wires are poorly connected ②、更换机芯 ②、敲击电机坏 Replace gear box Tapping motor failed ③、更换中心板 ③、中心板坏掉 Main PCB failed Replace the main PCB 手 控 器 上 按 键 无 ①、端子接触不良或线材接触不良...
  • Page 5 电机不振动 ①、振动电机坏 ①、更换振动电机 Vibration motors failed Replace the vibration motor no vibration by the ②、端子接触不良或是线材坏掉。 ②、将端子接插到位或者更换线材。 motor in the The terminals and wires are Plug the terminal well or seat-pad poorly connected or the replace the wires wires failed ③、更换中心板 ③、中心板坏。Main PCB failed Replace main PCB 座部不充气...
  • Page 6 音乐无功能 ①、端子接触不良 ①、将端子接好。 The terminals and wires are Plug the terminal well no music poorly connected ②、无输出为中心板坏 ②、检查端子是否有 24V 输出 Replace the main PCB if no voltage The output voltage is not 24VAC output ③ 检查喇叭是否损坏 ③、更换喇叭 The loudspeaker OK or not Replace the loudspeaker ④...
  • Page 7 二.故障检修流程图 Troubleshooting Process 在修理或者替换零配件过程中注意下面几点： A. 在拆卸连线，移动连接器，或者替换部件前一定要断开电源线插头。 B. 因为半导体（像集成电路，或者其它的）很容易被静电损坏，所以当要触摸 PCB 前，请确保你的身 体和大地有连线（佩带静电手环） ，或可以将手放在地端，以释放身体上所带的静电。 Notes for repairing chair or replacing parts A. Make sure the power is off when you tear down the wires, move terminals or replacing parts. B. The semiconductors( like IC or something else) will easily be damaged by static. So you touch the PCB before, please make sure your body is connected with the ground.
  • Page 8 No width switchover 2、机芯宽中窄不能切换 检查宽度检测板连接线是否与中心板连接好 将连接线接好 Does the terminal of Width Inspection Board and Touch well main PCB connected securely? 宽度检测板是否损坏 更换宽度检测板 Check width Inspection board Replace the width inspection 更换中心板 Replace Main PCB NO ROLLING 3、不行走/ 检查行走电机连接线是否与中心板连接好 将连接线接好 Check the terminals of rolling motor wire with Touch well main PCB connected securely? 检查行走电机是否损坏...
  • Page 9 4、不揉捏/ NO KNEADING 检查行走电机连接线是否与中心板连接好 否 将连接线接好 Check the terminals of Kneading motor wire Touch well with main PCB connected securely? 检查行走电机是否损坏 更换机芯 Check the Kneading motor Replace gear box 宽度检测板是否损坏 更换宽度检测板 Check width Inspection board Replace the width inspection 更换中心板 Replace the Main PCB 5、不敲击/ NO TAPPING...
  • Page 10 6、手控器上按键无反应 The all buttons of controller aren`t response 检查手控器连接线是否与中心板连接好 将连接线接好 Check the terminals of remote controller wire Touch well and main PCB connected securely? 检查导电橡胶是否损坏 更换导电橡胶 Check the conductive rubber Replace it 更换手控器 Replace the remote controller 7、电动推杆(靠背/小腿/零重力)不工作 Actuator doesn’t work.(Backrest/leg rest/zero G) 检查电动推杆连接线与中心板是否连接好...
  • Page 11 8、振动电机不工作 No vibration 检查振动电机连接线与中心板是否连接好 将连接线接好 The terminals of their print motors with main Touch well PCB connected securely? 检查座部振动电机对插线是否连接好 将连接线接好 Check the connectors in the middle of the wire Touch well connected securely? 检查振动电机是否损坏 更换振动电机 Check the print motor Replace print motor 更换中心板...
  • Page 12 检查气泵是否损坏 更换气泵 Check the inflator pump Replace the inflator pump 更换中心板 Replace the main PCB 10、小腿伸缩无功能 No extending or shrinking of the calves-rest 检查小腿连接板端子是否与中心板是否连接好 将连接线接好 Check the terminals of legrest with main PCB Touch well connected securely? 检查小腿内光电组件是否损坏 更换光电组件 Replace it Check the electric Subassembly 检查小腿电机接线是否连接好...

  • Page 13: Table Of Contents

    目录 Table of Contents 1.靠背的拆卸 Disassembly of the backrest ........................ 14  2.拉绒布的拆卸 Disassembly of the cloth of the front cover ..................15  3．靠背前后盖的拆卸 Disassembly of the backrest cover..................16  4. 机芯的拆解 Disconnect Robot Mechanism ......................16  5. 小车与背架的分离 Disconnect Rolling Car......................18  6.靠背小枕头的拆解...

  • Page 14: 靠背的拆卸 Disassembly Of The Backrest

    1.靠背的拆卸 Disassembly of the backrest A． 拉开披风与靠背的拉链，可将披风放在座位上。 Find the zipper on the top of the back rest, unzip it and then the backrest pad can be placed on the seat part. 将披风放在座位上 拉开披风与靠背连接的拉链 Place the backrest pad on the The zipper on the top of the seat part seat part backrest B.

  • Page 15: 拉绒布的拆卸 Disassembly Of The Cloth Of The

    A. Connecting rod (on the backrest) B. U stay fork of reclining actuator (on the seat) C. Flat head rivet D. Split pin F．现在可以把靠背竖起与座部的卡槽口并行，就样就容易把靠背从座部提起分离 Lift the backrest at 90 degrees, then take it away from the chair 靠背与座架成 90° Lift the backrest at 90 degrees. 2.拉绒布的拆卸...

  • Page 16: 3．靠背前后盖的拆卸 Disassembly Of The Backrest Cover

    3．靠背前后盖的拆卸 Disassembly and replacement of the rear cover and the front cover A．拉开靠背皮套的拉链,掀开皮套 Unfasten the zippers of the outer cloth of the rear cover. 靠背皮套的 2 边拉链 The zippers of the outer clothing of the rear cover. B． 取下背盖上的 4 颗螺丝，拿下后背盖 Find 4 pieces of screws fixing the rear cover and remove the screws with a plus screwdriver.
  • Page 17 A. 拆除机芯与小车的固定螺丝(4PCS) Disconnect mechanism with rolling car 机芯上方 2 枚螺丝 Slacken and remove the screw(2pcs) on upper 机芯下方 2 枚螺丝 Slacken and remove the screw(2pcs) on lower B. 宽度检测板和敲击电机的拆卸 Disconnect width inspection board and tapping motor 拆除 2 枚螺丝后就可取出检测板 拆除 4 枚螺丝和皮带 Disconnect width inspection board 即可拆卸敲击电机...

  • Page 18: 小车与背架的分离 Disconnect Rolling Car

    5. 小车与背架的分离 Disconnect Rolling Car A. 拆除背架顶端的横条 Remove the rail on the top of backrest 拆 除 背 架 顶 端 两 侧 的两个螺丝 Slacken and remove the screws (2pcs)on the two side B. 使小车从齿轨中走出来，有两种方法： ①给行走电机加 24V 直流电压，此方法省力省时 ②用冶具（例“—”螺丝刀） ，来旋转电机机轴，比较麻烦；见下图 Remove rolling car take from rack rail have 2 ways ①Fist way is better than②...

  • Page 19: 7．靠背大枕头的更换 Replace The Pillow(Big)

    B：拉开小枕头的拉链，掀开皮套，断开气管 Unzip the zipper of the pillow（small） ，lift the cover，disconnect the hose 小枕头上的拉链 断开此处的气管可以分离小枕头 The zipper of the pillow（small） Disconnect the hoses of the pillow C．可以直接更换小枕头上的气袋 Then replace the air bag of the pillow（small） 7．靠背大枕头的更换 Replace the pillow(big) A．取下小枕头（参考靠背小枕头的拆解） Take down the small pillow(refer to the disassembly of the small pillow) B．拉开大枕头的拉链，取下大枕头...

  • Page 20: 9．肩部按摩器的拆卸 Disassembly Of The Shoulder Massage

    9．肩部按摩器的拆卸 Disassembly of the shoulder massage A．拉开肩部按摩器的拉链 Unzip the zipper of the shoulder massage 肩部按摩器的拉链 2 边的肩部按摩器 the zipper of the shoulder the shoulder massage B．拔开气管和喇叭接线头，取下 3 枚螺丝 Disconnect the hose，slack and remover the 2 screws 断开肩部按摩器的气管和喇叭接线头 取下 3 枚螺丝就可以分离肩部按摩器了 disconnect the hose and the terminal of the loudspeaker Take down the 3 screws to disassemble the 10．侧板的拆卸...

  • Page 21: 11．手控器的更换 Replace The Remove Control

    开倒背，取下侧板后部的内六角螺丝 、 Put down backrest，hexagon screw in 侧板前部的内六角螺丝 behind of sideboard Hexagon screw in front of sideboard B．90°竖直将侧板拉起 Lift the side boards at 90 degrees, then disassemble it from the chair. 11．手控器的更换 Replace the remove control A．取下靠背（参考靠背的拆卸） Take down the backrest（refer to the disassembly of backrest） B．剪开手控器线处的扎扣...

  • Page 22: 12．坐垫的拆卸 Disassembly Of The Seat Pad

    D．更换手控器 Replace a new remote control 12．坐垫的拆卸 Disassembly of the seat pad A．拉开座垫与小腿连接的拉链和座垫与披风连接的拉链 Unzip the zipper fixing seat pad and leg rest，unzip the zipper fixing seat pad and backrest pad. 座垫与小腿连接的拉链 座垫与披风连接的拉链 the zipper fixing seat pad and backrest the zipper fixing seat pad and backrest pad B．断开座部气袋的气管...

  • Page 23: 13．座侧按摩器的拆卸 Disassembly Of The Side Seat Massage

    D．取下座垫，剪开拉链处的扎扣，拉开拉链更换皮套 Take down the seat，cut the cable tie，then unzip the zipper，take down the cover 座垫背部的拉链（有扎扣） 取下皮套 The zipper of the seat pad（with cable tie） Take down the cover E．拉开气袋粘毛扣，断开气管接头，可以取下气袋 Pull the tie as the picture below，disconnect the hose，take down the air bag 座部气袋的粘毛扣...

  • Page 24: 更换前挡板 Replace Front Board

    C．拉开座侧按摩器的粘毛扣，取下皮套 Open the cover of the side massage，take down the cover 取下皮套 Take down the cover D．取下座侧按摩器气袋上的螺丝，断开气管接头，更换气袋 Slack and remove the screws of the air bag，disconnect the air hose，replace the air bag 座侧按摩器气袋上的螺丝 座侧按摩气袋气管接头 The screws of the air bag on The terminal of the air hose the side massage on the side massage...

  • Page 25: 更换靠背&座部&小腿电动推杆 Replace The Backrest 、Seat-Rest And Legrest Actuator

    15. 更换靠背&座部&小腿电动推杆 Replace the backrest 、seat-rest and legrest actuator A：取下前挡板后，可以清楚的看到三个电动推杆分布位置 After take the front board , you can see the different actuatores distribution B: 取下电动推杆的波浪形卡口销及销轴 分离电动推杆端子. ， Take away the two pins and disconnect wire terminal of a actuator(if you need) Backrest`s actuator Legrest `s actuator Zero-G (seat rest) actuator...

  • Page 26: 17．小腿组件的拆卸 Disconnect Legrest

    泄气阀 air valve 中心板 main PCB 储气盒 gas storage 变压器 transformer 充气泵 inflator pump 音频板 music PCB 滤波器 filter 在这个平台上,你可以根据需要进行更换部件或维护, 具体的部件可以在上图找到,只需取下螺丝等即可拆离. You can replace the which part that the part was broken on the board; Please refer the picture above, then remove the fixing thing just 17．小腿组件的拆卸...

  • Page 27: 18．小腿电机的更换 Replacement The Extend Motor

    Open zipper between legrest and seat part `s pad , use tools slacken and remove the screws B：拉开连接坐垫与小腿皮套的拉链，利用 10MM 开口扳手和 5MM 内六角扳手 将连接小腿与座架的两个螺钉取下，即可让小腿与座架分离 Last,Slacken and remove the screw between legrest and seat rest , disconnect them 将 连 接 小 腿 推 杆 中 间管的销轴取下...

  • Page 28: 19．小腿行程光电的更换 Legrest `S Stroke Photo-Electricity

    C：用十字螺丝刀取下固定行走电机螺钉， 即可将行走电机取下 Slacken and remove the screws(4pcs) on the motor And take away the motor D：取一新的行走电机装上即可，安装时应注调整小皮带轮的位置， 使它与大皮带轮在同水平面内，这样可以提高其性能并且可以延长皮带的寿命 Last , How to tear the motor down and how to set it up, but you need note that the moto belt muxt set it well 19．小腿行程光电的更换...

  • Page 29: 22．小腿丝杆螺母座的更换 Replace Pin Rocker Bearing `S Nut

    使长度最长 Adjust actuator to longest Turn on the belt of motor to set axletree is longest B：取下触地检测开关保护盖，然后拔掉检测开关上的端子 Open the save box of senors switch and disconnect wire terminal C：用十字螺丝刀和 7mm 的扳手将固定开关的螺栓取下,再取一新的检测开关换上， 更换步骤按上述步骤逆向进行即可 Use tools take away the fixing the pin,and remove the screws ,replace new one set it up 触地检测...

  • Page 30: 23．小腿外套的更换 Replace Legrest `S Coat

    B：稍用力将有电机的另一端的固定丝杆的轴承座敲下来，这样就可以将丝杆螺母座旋 转出丝杆，从而进行更换。更换步骤按上述逆向操作即可 Percuss pin rocker bearing side of motor, please consult the steps as below of image 轻敲此轴承座 轴承座敲下后 旋下的丝杆螺母座 Percuss pin rocker bearing After percuss nut part 丝杆螺母及螺母橡胶套座 丝杆螺母座及丝杆螺母座 pin rocker Disconnect them Take away the bearing `s nut 23．小腿外套的更换...
  • Page 31 固定上小腿的螺钉的位置座 固定上小腿侧面的螺钉座 Screws tightening the upper part Screws fixing the outer coating C：取下上小腿，然后拉开皮套的拉链，即可将上小腿外套取下 Take down the upper footrest and then unfasten the zippers between the upper and lower part of the foot rest, then the outer coating can be remove Lower part A：旋转小腿行走皮带轮使小腿伸长到最大，...
  • Page 32 Remove the nuts fixing the lower part of the foot rest 固定 PE 板的十字盘头螺钉(6pcs) 法兰螺母（2 pcs） Screws fixing the PE board(6pcs) Nuts fixing the lower part（2pcs） Ｄ：用十字螺丝刀取下固定下小腿的十字盘头螺丝， 即可将下小腿取下，并更换下小腿外套; 更换外套时，按上述步骤逆向进行即可 Remove the screws fixing the lower part of the footrest, then the outer coating can be removed. Proceed in the reverse order of disassembly when assembly.

Table of Contents