Makita AN942 Instruction Manual
  1. Manuals
  2. Brands
  3. Makita Manuals
  4. Nail Gun
  5. AN942
  6. Instruction manual

Makita AN942 Instruction Manual

Pneumatic framing nailer
Hide thumbs Also See for AN942:

Advertisement

Table of Contents

See also: Instruction Manual
Pneumatic Framing
Nailer
MODEL AN942
004292
I N S T R U C T I O N
M A N U A L
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Advertisement

Table of Contents
loading

Related Manuals for Makita AN942

Summary of Contents for Makita AN942

  • Page 1 Pneumatic Framing Nailer MODEL AN942 004292 I N S T R U C T I O N M A N U A L WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

  • Page 2: Specifications

    SPECIFICATIONS Model AN942 Air pressure 0.44 - 0.83 Mpa (4.4 - 8.3 bar) Nail Iength 50 mm - 90 mm Nail capacity 60 - 84 pcs. Dimensions (L X H X W) 446 mm X 376 mm X 108 mm Min.

  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS ENB087-1 WARNING: WHEN USING THIS TOOL, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. For personal safety and proper operation and An improperly functioning tool must not be •...
  • Page 4 On rooftops and other high locations, nail as • you move forward. It is easy to lose your footing Ask Makita’s Authorized service centers for peri- • if you nail while inching backward. When nailing odical inspection of the tool.

  • Page 5: Installation

    INSTALLATION Selecting compressor 004293 • Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing (CFM) frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 40 times per minute at a compression of 0.59 MPa (5.9 bar), a compressor with an air output over 3 CFM (ft /minute) is required.

  • Page 6: Functional Description

    • When an air set is not used, oil the tool with pneumatic tool oil by placing 004296 2 (two) or 3 (three) drops into the air fitting. This should be done before and after use. For proper lubrication, the tool must be fired a couple of times after pneumatic tool oil is introduced.

  • Page 7: Loading Nailer

    • To adjust the depth of nailing, turn the adjuster so that the arrow above 004299 the adjuster will point to the number indicated on the adjuster. The depth of nailing is the deepest when the arrow points to the number 1. It will become shallower as the arrow points to higher number.
  • Page 8 • Depress the nail stopper and remove the strip of nails from the 004303 magazine. 1. Nail stopper Connecting air hose • Lock the trigger. Slip the air socket of the air hose onto the air fitting on 004304 the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting.
  • Page 9 • For No. 1 method, set the change lever to the “Intermittent Nailing” 004307 position. For No. 2 method, set the change lever to the “Continuous Nailing” position. After using the change lever to change the nailing method, always make sure that the change lever is properly set to the position for the desired nailing method.

  • Page 10: Maintenance

    Nails • Handle nail strips and their box carefully. If the nail strips have been 004310 handled roughly, they may be out of shape or their connector breaks, causing poor nail feed. • Avoid storing nails in a very humid or hot place or place exposed to direct 004311 sunlight.
  • Page 11 • Make sure that the trigger is locked when the change lever is set to the 004314 LOCK position. 1. Change lever 2. Trigger lock • When the tool is not to be used for an extended period of time, lubricate 004315 the tool using pneumatic tool oil and store the tool in a safe place.
  • Page 12 Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. To maintain product SAFETY and RELIABILITY, repairs, any other mainte- nance and adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.
  • Page 13 Memo...
  • Page 14 Memo...
  • Page 15 Memo...
  • Page 16 Makita Corporation 884238A976...

Table of Contents