Specific Safety Rules - Makita HR4501C Instruction Manual

Work mode : chiseling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 25 mm
diameter and 180: mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
For Model HR4510C
For European countries only
Noise
The typical A-weighted noise level determined according
to 60745-2-6:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function with side handle
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : chiseling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 25 mm
diameter and 180: mm depth
Vibration emission (a
Uncertainty (K) : 2 m/s
For Model HR4511C
For European countries only
Noise
The typical A-weighted noise level determined according
to 60745-2-6:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Vibration
The vibration total
determined according to EN60745-2-6:
Work mode : chiseling function with side handle
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : chiseling function with side grip
Vibration emission (a
Uncertainty (K) : 1.5 m/s
Work mode : hammer drilling into concrete, 25 mm
diameter and 180: mm depth
Vibration emission (a
Uncertainty (K) : 1.5 m/s
2
) : 12.5 m/s
h,CHeq
2
2
) : 16 m/s
h,HD
2
) : 93 dB(A)
pA
) : 104 dB(A)
WA
value (tri-axial vector
2
) : 8.5 m/s
h,CHeq
2
2
) : 8.5 m/s
h,CHeq
2
2
) : 9.5 m/s
h,HD
2
) : 94 dB(A)
pA
) : 105 dB(A)
WA
value (tri-axial vector
2
) : 7 m/s
h,CHeq
2
2
) : 7.5 m/s
h,CHeq
2
2
) : 7.5 m/s
h,HD
2
ENG306-1
EC-DECLARATION OF CONFORMITY
Model; HR4501C,HR4510C,HR4511C
We declare under our sole responsibility that this
ENG303-1
product is in compliance with the following standards of
standardized documents;
EN60745, EN55014, EN61000 in accordance with
Council Directives, 2004/108/EC, 98/37/EC.
ENG102-1
000230
Responsible Manufacturer:
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
ENG216-1
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
sum)
8JD, ENGLAND

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
ENG306-1
(gained from repeated use) replace strict adherence
to rotary hammer safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
ENG303-1
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping
ENG102-1
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
the operator.
4. Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun
glasses are NOT safety glasses. It is also
highly recommended that you wear a dust
ENG216-1
mask and thickly padded gloves.
5. Be sure the bit is secured in place before
sum)
operation.
6. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
ENG306-1
operation.
7. In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
ENG303-1
while by operating it under no load. This will
loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
8. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
5
CE2007
Tomoyasu Kato
Director
ENH101-8
GEB007-2