Set-Up Codes; Washer Diagnostic Mode - Whirlpool 3LCHW9100YQ Installation Instructions Manual

Set-up Codes

The DELICATES/KNITS key pad will advance you from code
■
to code.
The PERM PRESS key pad will change the code value.
■
The QUICK CYCLE key pad will select or deselect options.
■
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
CODE EXPLANATION
WASH LENGTH
711
711 This is the number of minutes for WASH. Washer
comes from the factory preset with 11 minutes.
Choose from 11–17 minutes by pressing the
PERM PRESS key pad.
• Press the DELICATES/KNITS key pad once to
advance to next code.
NOTE: This option does not apply to the Quick
Cycle.
ADDITIONAL RINSE OPTION
8 00
This option is either SELECTED "ON" or NOT
SELECTED "OFF."
8 00 Not Selected "OFF."
8 Ar Selected "ON." Cannot be combined with the
Super Cycle rinse option.
Press the QUICK CYCLE key pad once for this
selection.
• Press the DELICATES/KNITS key pad once to
advance to next code.
CYCLE COUNTER OPTION
9 00
This option is either SELECTED "ON" or NOT
SELECTED "OFF."
9 00 Not Selected "OFF."
9 0C Selected "ON" and not able to be deselected.
Press the QUICK CYCLE key pad 3 consecutive
times to select "ON." Once selected "ON" it
cannot be deselected.
• Press the DELICATES/KNITS key pad once to
advance to next code.
CODE EXPLANATION
5. 00 TIME-OF-DAY CLOCK, MINUTES
5. 00 This is the TIME-OF-DAY CLOCK, minute setting;
select 0–59 minutes by pressing the PERM
PRESS key pad.
• Press the DELICATES/KNITS key pad once to
advance to next code.
6. 00 TIME-OF-DAY CLOCK, HOURS
NOTE: Uses the 24 hr. clock.
6. 00 This is the TIME-OF-DAY CLOCK, hour setting;
select 0–23 hours by pressing the PERM PRESS
key pad.
• Press the DELICATES/KNITS key pad once to
advance to next code.
12
CODE EXPLANATION
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds
by pressing the PERM PRESS key pad. Factory
pre-set for 800 rpm.
• Press the DELICATES/KNITS key pad once to
advance to next code.
PREWASH LENGTH
A1. 00
A1. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select
between 2 and 7 minutes by pressing the PERM
PRESS key pad.
• Press the DELICATES/KNITS key pad once to
advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high-speed
spin. Choose from 3–8 minutes by pressing the
PERM PRESS key pad.
• Press the DELICATES/KNITS key pad once to
advance to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles
in HUNDREDS.
2 00 Number of cycles
in ONES.
TOTAL CYCLES = 225 cycles
This is "VIEW ONLY" and cannot be cleared.
• Press the DELICATES/KNITS button once to advance to next
code.
EXIT FROM SET-UP MODE
Remove power, open console, reinsert plug into AA1, close
console, and apply power.

Washer Diagnostic Mode

To enter the "Washer Diagnostic Mode," first enter "Start
Operating Set-up." Then press and hold the QUICK CYCLE key
pad for 1 second while in set-up code 6, anytime a diagnostic
code is present.
On entry to diagnostic mode the entire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diagnostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options are
permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. Washer Cleanout cycle – With the entire display flashing, this
cycle is started by pressing the BRIGHTS key pad.
Use the Washer Cleanout cycle once a month to keep the
inside of your washer fresh and clean. This cycle uses a higher
water level. Use with liquid chlorine bleach to thoroughly clean
the inside of the washer. This cycle should not be interrupted.
IMPORTANT: Do not place garments or other items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
1 02 = 200
2 25 = 25