Advertisement
Quick Links
Download this manual
See also:
Service Manual
27" "S" OVEN VENT CONVERSION KIT 35-00-624
INSTALLATION INSTRUCTIONS
FOR THERMADOR
This conversion kit instructs the service technician on how to convect the upper and
lower plenum body to our redesign vent system.
5551 MCFADDEN • HUNTINGTON BEACH, CALIFORNIA 92649 • TELEPHONE: 800 /735-4328
ECO 11886 -02 • Lit. No. 96-93-563C
UPPER OVEN
LOWER OVEN
COOK
STOP
3
OFF
TIME
TIME
1
2
BAKE
BAKE
OFF
TIMER 1
TIMER 2
4
5
6
BROIL
SELF
CLEAN
BROIL
CLEAN
SELF
CLOCK
OVEN
CONVECTION
CONVECTION
CONVECTION
CONVECTION
LIGHT
7
8
9
ROAST
ROAST
0
®
BUILT -IN ELECTRIC OVENS
1
Models:
SCD272T
SC272T
S272T
January 1999
Advertisement
Related Manuals for Thermador SCD272T
Summary of Contents for Thermador SCD272T
-
Page 1: Installation Instructions
CONVECTION CONVECTION CONVECTION CONVECTION LIGHT ROAST ROAST Models: SCD272T SC272T S272T INSTALLATION INSTRUCTIONS ® FOR THERMADOR BUILT -IN ELECTRIC OVENS This conversion kit instructs the service technician on how to convect the upper and lower plenum body to our redesign vent system. - Page 2 THESE KITS WILL BE COMPRISED OF THE FOLLOWING: Quantity Description Part Number Upper Vent Tube 16-10-058 Lower Vent Tube 16-10-059 Insulation 14-38-692 Templets (Inside of Instructions) Screws 14-91-102 Kit Instructions 96-93-563 Rev A Bracket Blower Mounts 14-38-482-01 NOTE: THE OVEN WAS SHIPPED WITH THE THERMOSTAT ADJUSTED AT +25 DEGREES. WITH THE NEW UPWARD VENT, THE OVEN NEEDS TO BE CALIBRATED TO ZERO.
- Page 3 REMOVE FRONT OVEN TRIMS: 1) REMOVE BOTTOM TRIM (4 screws). 2) REMOVE SIDE TRIMS (4 screws on each trim). FIGURE 2. Remove the two screws from the bottom trim, pull it forward Side and remove it. T ri m Install the lower vent trim and secure with (2) screws provided, one at each top end corner of the trim.
- Page 4 REMOVE FRONT VENT COVER. (4 screws) REMOVE THE 2 LIGHT SWITCH WIRES. See Figure 4 Remove the air vent by removing the FIGURE 4. two bottom screws and the two front oven door latch screws. Pull the vent forward and unsnap it from the oven. To remove the oven light switch, remove the wires from the terminals, then press in on the locking arms, and push it out...
- Page 5 REMOVE REAR OVEN PANELS: 1) REMOVE REAR COVER. (20 screws) 2) REMOVE TOP OVEN VERTICAL VENT TUBE. ( 10 screws). See Figure 7. 3) REMOVE VERTICAL CHANNEL SUPPORT. (10 screws). See Figure 7. 4) REMOVE (5) RED WIRE TIES. 5) REMOVE WIRE HOLDER. 6) DISCONNECT WIRES AT BROIL ELEMENT.
- Page 6 PREPARE OVEN PLENUM FOR CONVERSION: REMOVE BLOWER AND BLOWER BRACKET FROM PLENUM. (bracket must be changed). Remove the three screws 3, 4 and 5 that mount the motor to the bracket. See Figure 8. FIGURE 8. LOWER BLOWER BRACKET Blower Bracket Remove the three screws from the blower motor bracket on the back of the plenum and turn the assembly around so thhat the back faces you.
- Page 7 PLACE TEMPLATE ON PLENUM AND MARK, PUNCH AND DRILL HOLES. FIGURE 10. FIGURE 11. See Detail “B” Figure 12, for Blower Mounting Hole Modification Template Location Top Vent Hole Detail (See Top Template)“A” Page 8. 3) INSTALL NEW BRACKET AND REINSTALL BLOWER.). Install the new blower in the mounting bracket and mount the assembl;y to the plenum.
- Page 8 “A”...
- Page 9 REMOVE TOP PLENUM: REMOVE 4 SIDE SCREWS ON EACH SIDE THAT ATTACH THE PLENUM TO THE TOP OVEN CAN CELL. LIFT THE PLENUM UP AND SECURE THE NEW VENT AND INSULATION TO THE UNDERSIDE OF PLENUM WITH THE 4 TOP SCREWS PROVIDED. LIFT THE PLENUM AND SLIDE IT FORWARD, IT IS NOT NECESSARY TO REMOVE THE PLENUM OFF OF THE UPPER CAN CELL.
- Page 10 TO CONVERT TOP OVEN CELL: REMOVE SCREW IN REAR OF PLENUM THAT HOLDS VENT TUBE TO OVEN WRAPPER. REACH UNDER INSULATION BLANKET AND PULL VENT TUBE UP AND OUT OF CATALYST. SLIDE PLENUM OVER TOP OF OVEN CELL AND LINE UP NEW VENT TUBE WITH CATALYST. FIGURE 14.
- Page 11 TO REMOVE THE TOP OVEN CELL FROM MID PLENUM: DISCONNECT THE 2 LIGHT HARNESS PLUGS. DISCONNECT UPPER AND LOWER PROBE HARNESSES AT THE RELAY BOARD. DISCONNECT WIRES AT BAKE ELEMENT. REMOVE 4 SCREWS ON EACH SIDE THAT ATTACH THE TOP OVEN CAN CELL TO THE MID PLENUM.
- Page 12 PREPARE MIDDLE OVEN PLENUM FOR CONVERSION: REMOVE BLOWER AND BLOWER BRACKET FROM PLENUM. (bracket must be changed). Remove the three screws 3, 4 and 5 that mount the motor to the bracket. See Figure 17. FIGURE 17. LOWER BLOWER BRACKET Blower Bracket Remove the three screws from the blower motor bracket on the back of the plenum and turn the assembly around so thhat the back faces you.
- Page 13 PLACE TEMPLATE ON PLENUM AND MARK, PUNCH AND DRILL HOLES. FIGURE 19 See Detail “C” for Blower Mounting Hole Modification Template Location Middle Vent Hole Detail (See Middle Template “B”) INSTALL NEW BRACKET AND REINSTALL BLOWER. Install the new blower in the mounting bracket and mount the assembl;y to the plenum. FIGURE 19A.
- Page 15 REMOVE TOP PLENUM: REMOVE 4 SIDE SCREWS ON EACH SIDE THAT ATTACH THE PLENUM TO THE TOP OVEN CAN CELL. LIFT THE PLENUM UP AND SECURE THE NEW VENT AND INSULATION TO THE UNDERSIDE OF PLENUM WITH THE 4 TOP SCREWS PROVIDED. LIFT THE PLENUM AND SLIDE IT FORWARD;...
- Page 16 TO CONVERT LOWER OVEN CELL: REMOVE SCREW IN REAR OF OVEN CELL THAT HOLDS VENT TUBE TO OVEN WRAPPER. REACH UNDER INSULATION BLANKET AND PULL VENT TUBE UP AND OUT OF CATALYST. FIGURE 21. Rear Screw “Old” Vent Tube (Pull Up) Catalyst...
- Page 17 SLIDE PLENUM OVER TOP OF OVEN CELL AND LINE UP NEW VENT TUBE WITH CATALYST: SECURE PLENUM TO LOWER OVEN CELL. COVER SQUARE HOLE FOR OLD VENT TUBE WITH ALUMINUM TAPE. FIGURE 22. Slide Plenum Square Hole with Aluminum Tape (4) Side Screws...
- Page 18 RE ASSEMBLE OVEN: REINSTALL THE TOP OVEN CELL ON TO THE MID PLENUM. REINSTALL VERTICAL VENT TUBE FOR STRUCTURE SUPPORT. REISTALL VERTICAL CHANNEL SUPPORT. REINSTALL WIRE HOLDERS. REINSTALL RED WIRE TIES. RECONNECT BAKE AND BROIL WIRES. RECONNECT WIRES AT CONVECTION MOTOR. REINSTALL REAR PANEL COVER.
- Page 19 REINSTALL OVEN DOOR: GRASP THE SIDES OF THE DOOR AT THE CENTER AND INSERT THE ENDS OF THE HINGES INTO THE SLOTS IN THE OVEN FRONT FRAME AS FAR AS THEY WILL GO (SEE ILLUSTRATION BELOW). WITH THE DOOR OPEN ALL THE WAY, LOWER THE TWO LOCKING CLIPS. REMOVE AND DISCARD THE CENTER INSERT DOOR GASKET.
- Page 20 RECALIBRATE OVEN TO ZERO DEGREES: OVEN TEMPERATURE CALIBRATION To recalibrate your oven: Touch Bake and then any number between 500° and 550°F or 260° and 290°C. Touch and hold Bake for 3 to 4 seconds. The ° is shown. By touching Broil repeatedly it will toggle between positive and negative degrees (-). Enter desired temperature from plus or minus 0°...