Page 1
Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr www.adjets.com Version 01/08/2008 AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 2
Can be used if you do not fit the interior in the fuselage. Fuel tank fits in the middle of the fuselage AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 3
All the plywood formers should be fitted with cyano adhesive and then glued with epoxy and glass fiber tape. All other parts should be glued with epoxy. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 4
Insert and glue with epoxy the four hinges in the control surface. Check that the control surface can rotate freely. All hinges must be perfectly glued. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 5
Connect the servo and the control horn with two x M3 links and M3 threaded rod. Apply thread lock. There must be no play. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 6
Let it dry overnight. Make a hole in the fin for the elevator servo lead. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 7
If you want to put this fairing, just sand carefully the fin and glue it with epoxy. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 8
Connect the servo and the control horn with two x M3 links and M3 threaded rod. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Fit engine hatch latches or screws on each side of the doors to have an easy access to the engine AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 10
Glue the fiber ring cover on both surfaces with microballoon AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 11
Secure the engine nacelle with one x M3x16 mm screw on each side through the aluminum tube AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 12
Make a 2 mm slot in the aileron for the control horn. Glue the control horn with epoxy. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 13
So it is possible not fit the flaps and save 2 servos and some weight. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Put the steering servo on one side on the pilot floor. Connect servo to the steering arm. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 15
Glue with slow epoxy and microballoon the two fiber tubes and the two plywood reinforcements. Let it dry overnight. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Drill the 4 x 2 mm hole for the gear screws Screw the gear with four 4x20mm parker screw AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 17
Adjust the position of the air cylinder and screw it on the plywood frame to have gear door closed when cylinder is closed. Check that it opens and closes without problem AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 18
Cut the front gear door in 3 parts according to the photos Put 2 gear door hinges on each front gear door AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 19
Fit the wheels and brakes on the gears. You have now to connect all the gear, door and brake tubing. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 20
Fit the Kevlar fuel tank on the mounting and hold it with rubber or plastic T rap AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 21
Put each canopy and hold them with tape outside Let it dry overnight. Same applies to all other windows. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 22
All seats and tables can be made from balsa and light foam. Always think weight to avoid excess weight. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Secure the door with small parker screws. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Think light: excessive paint build-up will add unnecessary weight to the model. Apply light, thin coats of paint and sand between coats to avoid excess weight. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Note : balance the model with the gear down and CG on the front screws AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...
Page 28
300 KPH. It is your responsibility to operate it safely. Specifications may change without notice. AVIATION DESIGN - ZI le Chenet - 91490 MILLY LA FORET – FRANCE - Tel : int+ 33 1 64 98 93 93 - aviation.design@wanadoo.fr – www.adjets.com...