Table of Contents
Advertisement
Quick Links
INDEX
Page Contents
2
Safety Information
3
Unpacking and preparation
4
Installation and start-up
14
Maintenance
16
Technical information
IGLOO WL C61199
IGLOO EASY C61197
IGLOO ECO C61196
INSTRUCTION MANUAL
Congratulations on choosing a Clay Paky product
We thank you for your custom.
Please note that this product, as all the others in the rich Clay Paky
range, has been designed and made with total quality to ensure
excellent performance and best meet your expectations and
requirements.
Carefully read this instruction manual in its entirety and keep it safe
for future reference. It is essential to know the information and
comply with the instructions given in this manual to ensure the fitting
is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or
to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the characteristics
stated in this instruction manual at any time and without prior notice.
1
1
Advertisement
Table of Contents
Related Manuals for Clay Paky IGLOO WL-C61199
Summary of Contents for Clay Paky IGLOO WL-C61199
- Page 1 Congratulations on choosing a Clay Paky product We thank you for your custom. Page Contents Please note that this product, as all the others in the rich Clay Paky Safety Information range, has been designed and made with total quality to ensure...
-
Page 2: Safety Information
SAFETY INFORMATION SAFETY INFORMATION IMPORTANT: Clay Paky recommends you carefully read and keep the safety information on this product, also available in digital format at the following link: http://www.claypaky.it/en Ref: [FIS014 – Safety Information Igloo] INFORMAZIONI DI SICUREZZA IMPORTANTE: Clay Paky raccomanda di leggere accuratamente e conservare le informazioni di sicurezza relative a questo prodotto, sempre reperibili in versione digitale al seguente link: http://www.claypaky.it/en/download... -
Page 3: Unpacking And Preparation
WARNING: For dimensional, thermal or operating problems, IGLOO use in CLAY PAKY projectors other than those listed or other brand projectors is NOT permitted. MINIMUM MAXIMUM PROJECTOR ambient temperature ambient temperature o Alpha 300 Series o Alpha 700 Series o Sharpy - 20 °C... -
Page 4: Installation And Start-Up
INSTALLATION AND START-UP With the bracket code C61177 is not necessary to remove WARNING: the side handles of SuperSharpy and Mythos. to avoid damaging the projector, use the screws supplied with the bracket unit and not the ones previously removed. Mounting brackets for projector placement - Fig. - Page 5 90° Projector placement - Fig. 2 Once placed in the igloo the projector is fixed to the base by tightening the screws using 1/4 turns secured to the brackets. Continue IGLOO...
- Page 6 Connecting and disconnecting power cable- Fig. 3 Connecting to the control signal line Igloo Easy (DMX) - Fig. 4 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified.
- Page 7 Wireless control - Fig. 5 The wireless control is only available in the IGLOO version (not EASY). Continue IGLOO...
- Page 8 DIP SWITCH 1: DMX ADDRESS SETTINGS DIP-SWITCH 2: RECEIVING CONTROL MODE SETTINGS The DMX address set on the Dip-switch 1, is the address to control the Switch 1, 2, 3 ON: Switch 1, 2, 3 OFF: switching-on / switching-off of the device via the control unit. Wireless operating mode (Radio) Wired operating mode (DMX cable) 9 10...
- Page 9 DMX connection cable for IGLOO (not EASY) - Fig. 7 PLEASE NOTE: If you do not intend to use the wireless option, the DMX cable must be connected as seen in fig.7 and not directly to the projector. Closing the device - Fig. 8 Continue IGLOO...
- Page 10 CAUTION: The 2 IGLOO conveyors should always be facing down. By gripping them with both hands it is possible to rotate them in the desired position. An acoustic signal will alert incorrect conveyor positions. Installing Igloo - Fig. 9 WARNING: with the exception of when the Igloo is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
- Page 11 C61193 - OPTIONAL ACCESSORIES 2 x 183102/805 1 x 272023/001 1 x 033205 1 x 105041/003 Mounting kit C61193 - Fig. 10 Continue IGLOO...
- Page 12 CAUTION: To avoid damage to the internal parts of the fixture, installed inside the IGLOO, when the fixture is not working, is recommended to turn the head down before turning the fixture off, so that the front lens of the fixture is invested as little as possible from the sun.
- Page 13 Lock assembly - Fig. 12 The device latches are fitted with holes for affixing safety locks if desired. IGLOO...
-
Page 14: Maintenance
MAINTENANCE Replacing fuse - Fig. 13 IGLOO... - Page 15 WARNING: no alcohol Periodical cleaning - Fig. 14 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the working environment (air humidity, presence of dust, salinity, etc.).
-
Page 16: Technical Information
32 Kg (70.6 lbs). Note: Carefully read the instruction manual, dedicated to the projector inside the Igloo, for additional technical details. CLAY PAKY - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it S.p.A.
Need help?
Do you have a question about the IGLOO WL-C61199 and is the answer not in the manual?
Questions and answers