Troubleshooting - Marantz cd5003 User Manual

ENGLISH

TROUBLESHOOTING

In a case of trouble, check the items below. Incorrect operations can sometimes be taken for trouble and
malfunctions. If the trouble persists even after the following points have been checked, consult your dealer
or nearest Marantz sales office or service center.
Symptoms
The power cable is not plugged
in.
The power to this unit is not
turned on.
The disc is not placed correctly.
The disc is placed upside-down.
A disc does not rotate. (The label of the disc is facing
down.)
The disc is dirty.
The disc is scratched.
The disc is warped.
An amplifier or speakers are not
connected correctly.
The power to the amplifier is not
turned on.
The disc rotates, but there
The function or the selector
is no sound output.
switch of the amplifier is not set to
"CD" or "AUX" (according to your
current connection setup).
The volume of the amplifier is set
to minimum.
The disc is dirty.
The disc is scratched.
The disc stops rotating.
The disc is warped.
The disc to be played is not a
music CD. Or MP3/WMA files are
not recorded on the disc.
30
Causes Action
Plug the power cable into an AC outlet.
(page 9)
Turn on the power to the unit.
(page 10)
Place the disc correctly.
(page 10)
Place the disc correctly.
(page 10)
Clean the recorded side of the disc. (page
33)
A disc with many scratches may not be
playable. (page 33)
A warped disc may not be playable.
(page 33)
Connect the cables correctly. (Refer to
User Guide supplied with the amplifier.)
Turn on the power to the amplifier.
(Refer to User Guide supplied with the
amplifier.)
Set the function or the selector switch of
the amplifier to "CD" or "AUX" (as per your
connection setup).
(Refer to User Guide supplied with the
amplifier.)
Adjust the volume of the amplifier. (Refer to
User Guide supplied with the amplifier.)
Clean the recorded side of the disc. (page
33)
A disc with many scratches may not be
playable. (page 33)
A warped disc may not be playable. (page
33)
A CD-ROM for a computer cannot be
played. (page 32)
Symptoms Causes
The distance between the unit
and a remote controller is too
great.
Some object is placed between
the unit and remote controller.
The remote controller The batteries in the remote
cannot be operated. controller are exhausted.
The remote sensor of the unit is
exposed to strong light.
T h e R E M O T E C O N T R O L
switch on the rear panel is set to
EXTERNAL.
The disc is placed upside-down.
The recorded information is not
A C D - R / C D - RW d i s c
in a music (CD-DA) format. Or
cannot be played.
MP3/WMA files are not recorded
correctly.
Pitch control operation The unit is not set to Audio EX
cannot be performed. OFF.
Digital output is set to OFF.
Digital signals are not Audio EX is set to Audio EX2.
output.
Audio EX is set to Audio EX OFF,
and the pitch control is used.
Action
Use the remote controller nearer the unit,
within the operational range. (page 4)
Remove the object. (page 4)
Replace all the batteries with new ones.
(page 4)
Avoid exposing the remote sensor to the
strong light. (page 4)
When the unit is to be used alone, set the
switch to INTERNAL. (page 13)
Place the disc correctly. (page 10)
Record correct data appropriate for the
unit. (page 32)
Set the unit to Audio EX OFF. (page 24)
Set digital output to ON. (page 24)
Set Audio EX to Audio EX1. (page 24)
Set the pitch control setting to O. (page 21)
Or set Audio EX to Audio EX1. (page 24)