Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
This document is provided as a quick reference for installation, signal acquisition, and authorization of DSR-
6402 Satellite Multiplex Receiver/Transcoders for use by Discovery Communications. For complete information
on configuration and operation, please refer to the Motorola DSR-6400 Series Satellite Multiplex Receiver/
Transcoder Operator Guide.
The DSR-6402 must be properly grounded, and the shield of the coaxial cable is earthed in accordance with
Article 820.93 of the NEC, ANSI/NFPA 70:2005 or equivalent.
Installation Overview
This procedures in this guide assume that the DSR-6402 has been properly mounted in a suitable equipment
rack with access to electrical power and the required input and output signal connections. The installation
sequence described here consists of connecting the input and output cabling and using the front-panel
interface to perform initial configuration for acquisition and tuning of the received signals.
Connecting the DSR-6402
The following paragraphs describe the rear-panel connections to be made to the DSR-6402 to enable the
Discovery services.
1
10/100
Input Connection
RF IN Port 1: Galaxy 13 C-Band at 127 West Longitude, Transponder 14 (Horizontal).
Note: There is no LNB voltage output from ports 2 through 8; if using one of these ports, and if
LNB power is needed, it can be activated for Port 1, and Port 1 can then be added to a one-port
power-passing splitter to power one LNB.
RF IN Port 2: AMC-10 C-Band at 135 West Longitude, (Horizontal).
RF IN Port 3: AMC-10 C-Band at 135 West Longitude, (Vertical).
RF IN Port 4: AMC-11 C-Band at 131 West Longitude, (Horizontal).
Discovery Communications
DSR-6402 Installation Guide
2
3
ASI IN
GIGE
ETHERNET
(Phase 1)
RF IN
4
5
6
ASI OUT 1
ASI OUT 2
VIDEO OUT OSD VIDEO OUT
7
8
Advertisement
Related Manuals for Motorola DSR-6402
Summary of Contents for Motorola DSR-6402
-
Page 1: Installation Overview
Motorola DSR-6400 Series Satellite Multiplex Receiver/ Transcoder Operator Guide. The DSR-6402 must be properly grounded, and the shield of the coaxial cable is earthed in accordance with Article 820.93 of the NEC, ANSI/NFPA 70:2005 or equivalent. -
Page 2: Output Connections
SD output is not intended for live use, and has no closed-caption support. Installation/Initial Configuration With power applied to the DSR-6402, the splash screen with the device name and version number will briefly appear, followed by the main menu as shown. DSR-6402 menu items that are selectable and/or configurable are identified by the right-pointing arrow adjacent to the item. - Page 3 Use the or keys to adjust the Symbol Rate to 30.000000, then press Enter. The cursor returns to the top line of the display. 4. On the DSR-6402 front panel, observe that the Signal LED is lit. 5. Use the key to move the cursor to the home position for this menu, then press Enter.
-
Page 4: Call For Authorization
2. Contact the Discovery project desk at (800) 308-6272 for authorization of the DSR-6402. The project desk is available from 8 a.m. to 8 p.m, Eastern Time. 3. When the Authorize signal is received, the front panel Authorized LED lights green. -
Page 5: Pid Mapping
DSR-6400 Series Operator’s Guide. PID Mapping The DSR-6402 uses a PID mapping scheme for the output services on the ASI OUT 1, ASI OUT 2, and GIGE output ports. The following two tables show the supported services and each of the individual service components for the DSR-6402, and their assigned PID values on each MPEG program. -
Page 6: Antenna Considerations
GIGE ETHERNET Copyright © 2012 Motorola Mobility, Inc. All rights reserved. MOTOROLA and the Stylized M Logo are registered trademarks and all other Motorola product names are trademarks or registered trademarks of Motorola Trademark Holdings, LLC. All other product or service names are the property of their respective owners.