Error Messages - Dell Precision 350 User Manual

3. Click Phone and Modem Options.
4. Click the Modems tab.
5. Click the COM port for your modem.
6. Click Properties, click the Diagnostics tab, and then click Query Modem to verify that the modem is communicating with Windows.
If all commands receive responses, the modem is operating properly.
Turn off call waiting (catch-phone) —
networking connection properties.
1. Click the Start button, and then click Control Panel.
2. Click Printers and Other Hardware, and then click Phone and Modem Options.
3. Click your connection type to highlight it.
4. Click the Dialing Rules tab, and then click Edit.
5. Click the To Disable Call Waiting box to place a checkmark in it.
6. Select the disable code from the drop-down menu (for example, *70).
7. Click Apply, and then click OK.
Ensure that you are connected to the Internet —
next to it, click the checkmark to remove it and connect to the Internet.
Ensure that you have subscribed to an Internet service provider —
Contact your Internet service provider —

Error Messages

If the message is not listed, see the documentation for the operating system or the program that was running when the message appeared.
A filename cannot contain any of the following characters: \ / : * ? " < > | —
A required .DLL file was not found —
program:
1. Click the Start button.
2. Click Control Panel.
3. Click Add or Remove Programs.
4. Select the program you want to remove.
5. Click the Change or Remove Program icon.
6. See the program documentation for installation instructions.
Alert! CPU Fan Not Detected —
Ensure that the cooling fan is properly installed and working. Also, ensure that the microprocessor airflow shroud is properly installed. See
"Microprocessor."
Alert! Previous attempts at booting this system have failed at checkpoint [nnnn ]. For help in resolving this problem, please note this
checkpoint and contact Dell Technical Support —
error. Contact Dell and report the checkpoint code (nnnn) to the support technician.
Alert! Previous Fan Failures — The fan caused an errors last time you used the computer. Ensure that nothing is blocking the airflow vents
and that all the fans are properly installed and operating correctly.
Alert! Previous Processor Thermal Failure —
blocking the airflow vents and that all the fans are properly installed and operating correctly. Also, ensure that the microprocessor heat sink
is properly installed.
Alert! Previous Reboot Was Due to Voltage Regulator Failure —
assistance.
Alert! Previous Shutdown Due to Thermal Event —
Ensure that nothing is blocking the airflow vents and that all the fans are working correctly. Also, ensure that the microprocessor heat sink is
properly installed.
Alert! Previous Voltage Failure —
Problems" and "System Board Problems."
Alert! System Battery Voltage is Low —
Alert! Unable to Initialize all Installed Memory —
Problems."
Alert! Uncorrectable Memory Error Previously Detected... Address xxxxxxxxh, Device RIMM_Y —
improperly seated or faulty or the system board may be faulty. See
Attachment failed to respond —
"Hard drive problems" for troubleshooting suggestions.
Bad command or file name — Ensure that you have spelled the command correctly, have put spaces in the proper place, and have used the
correct pathname.
Bad error-correction code (ECC) on disk read —
problems" or "Hard drive problems" for troubleshooting suggestions.
Controller has failed — The hard drive or the associated controller is defective. See "Floppy drive problems" or "Hard drive problems" for
troubleshooting suggestions.
Data error — The floppy or hard drive cannot read the data.
For the Microsoft® Windows® operating system, run the chkdsk utility to check the file structure of the floppy or hard drive.
l
For another operating system, run the appropriate corresponding utility.
l
See your operating system documentation for information on running these utilities.
Decreasing available memory —
Reinstall the memory modules and, if necessary, replace them.
l
See "Memory Problems" for additional troubleshooting suggestions.
l
See your telephone directory for instructions on deactivating this feature. Then adjust the dial-up
With the Outlook Express e-mail program open, click File. If Work Offline has a checkmark
Contact your Internet service provider for assistance.
The program that you are trying to open is missing an essential file. To remove and then reinstall the
The microprocessor cooling fan is not installed, has failed, or is not properly connected to the system board.
The computer failed to complete the boot routine three consecutive times for the same
The microprocessor overheated that last time you used the computer. Ensure that nothing is
The microprocessor or hard drive overheated the last time you used the computer.
Voltage used by the computer either exceeded or fell below acceptable thresholds. See
The computer battery is providing inadequate voltage. See "Battery."
One or more memory modules may be improperly seated or faulty. See
The floppy or hard drive controller cannot send data to the associated drive. See
The floppy or hard drive controller detected an uncorrectable read error. See
One or more memory modules might be faulty or improperly seated.
Contact an Internet service provider to subscribe.
Do not use these characters in filenames.
The VRM failed the last time you used the computer.
"Memory Problems" and "System Board
Contact Dell for
"Power
"Memory
One or more memory modules may be
Problems."
"Floppy drive problems" or
"Floppy drive