Advertisement
Available languages
Available languages
www.jts-germany.de
Please read these operating instruc-
ENGLISH
tions carefully before operating the
microphone and keep them for later
reference.
1 Applications
This microphone KA-8TH /1 can be used in combi -
nation with the wireless audio transmission system
KA-10 /1PACK or with the tour guide pocket receiver
TG-10R /1. For wireless transmission, 16 channels
are available in the frequency range 863 – 865 MHz.
Up to three of these channels can be used at the
same time without mutual interference. The transmis-
sion range depends on local conditions and may
reach 60 m as a maximum.
1.1 Conformity and approval
Herewith, MONACOR INTERNATIONAL declare that
the wireless microphone KA-8TH /1 is in accordance
with the basic requirements and the other relevant
regulations of the directive 1999 / 5 / EC. The declara-
tion of conformity is available on request from MONA-
COR INTERNATIONAL. The microphone is licence-
free and generally approved for operation in EU and
EFTA countries.
2 Important Notes
The wireless microphone corresponds to all relevant
directives of the EU and is therefore marked with
G
The microphone is suitable for indoor use only. Pro-
tect it against dripping water and splash water, high
air humidity and heat (admissible ambient tempera-
ture range: 0 – 40 °C).
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the microphone and no lia-
bility for any resulting personal damage or material
damage will be accepted if the microphone is used
for other purposes than originally intended, if it is
not correctly operated, or if it is not repaired in an
expert way.
If the microphone is to be put out of opera-
tion definitively, take it to a local recycling
plant for a disposal which is not harmful to
the environment.
3 Inserting / Replacing the batteries
For power supply, two 1.5 V batteries of size AA are
required.
G
Only insert batteries of the same type and always
replace both of them.
G
If the microphone is not in use for a longer period of
time, always remove the batteries to prevent dam-
age due to battery leakage.
1) Unscrew the sleeve (8) on the lower end of the
microphone.
2) Insert the batteries with the positive and negative
poles as indicated in the battery compartment (10).
3) After setting the channel (chapter 4), screw the
sleeve on the microphone again.
Never put used batteries in the household
waste; always take them to a special waste
disposal, e. g. collection container at your
retailer.
Vertrieb von JTS-Produkten — Distribution of JTS products
4 Operation
1) Before switching on the microphone, set the re -
ceiver to an interference-free channel (see instruc-
tion manual of the receiver).
2) Switch on the microphone with the button POWER /
MUTE (7). The power LED (4) shows green. If it
shows red, the batteries are almost discharged and
should be replaced.
The display (3) indicates the transmission chan-
nel adjusted for a few seconds. Then it is extin-
guished. To illuminate the display for a few sec-
onds, press the button POWER / MUTE or SET (9).
3) Set the microphone to the transmission channel of
the receiver. Keep the button SET (9) pressed until
the dot starts flashing on the display. Then press
the button SET repeatedly or keep it pressed until
the desired channel is indicated. The channel has
been stored when the dot on the display stops
flashing (approx. 6 seconds after the last actuation
of the button SET).
4) If the microphone signal on the receiver is too low
or too high, change the microphone sensitivity:
Unscrew the microphone cartridge (1) to access
the control GAIN (6) for the microphone sensitivity
(on the handle). Use a small screwdriver to adjust
the sensitivity. Put the microphone cartridge on the
handle so that the 4-pole pin contacts (2, 5) of the
cartridge and the handle engage. Then screw the
.
cartridge on the handle.
5) To briefly mute the microphone, e. g. in speech /
music pauses, briefly press the button POWER /
MUTE. As an indication, the power LED keeps
flashing. To reactivate the sound, press the button
POWER / MUTE again.
6) To switch off the microphone, keep the button
POWER / MUTE pressed until the display is extin-
guished.
5 Specifications
Type of microphone: . . . condenser cartridge, cardioid
Carrier frequency range: 863 – 865 MHz,
Frequency stability: . . . . ±0.005 %
Transmission power: . . . < 10 mW (EIRP)
Audio frequency range: . 40 – 16 500 Hz
Ambient temperature: . . 0 – 40 °C
Power supply: . . . . . . . . two 1.5 V batteries of size AA
Dimensions, weight: . . . ∅ 51 mm × 260 mm, 280 g
Channel assignment
Channel
MHz
0
863.125
1
863.250
2
863.375
3
863.500
4
863.625
5
863.750
6
863.875
7
864.000
8
864.125
9
864.250
Subject to technical modification.
®
for channel assignment see
table below
Channel
MHz
A
864.375
B
864.500
C
864.625
D
864.750
E
864.875
F
865.000
MONACOR INTERNATIONAL GmbH & Co. KG, Zum Falsch 36, 28307 Bremen, Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved. A-1438.99.01.06.2013
©
KA-8TH/1
Wireless Microphone
863 – 865 MHz
1
2
3
4
POWER / MUTE
5
6
7
8
9
10
1 Microphone cartridge
2 Pin contact, matching the contact (5)
3 Display to indicate the channel
4 Power LED
green = batteries OK
red = batteries discharged
5 Pin contact for the microphone cartridge
6 Control GAIN for the microphone sensitivity
7 Button POWER / MUTE to switch on / off and to
mute the microphone
To switch on, press the button briefly.
To mute / unmute, press the button briefly; when
the microphone is muted, the power LED (4)
keeps flashing.
To switch off, keep the button pressed until the dis-
play is extinguished.
8 Screw sleeve
9 Button SET to set the channel
10 Battery compartment
GAIN
Advertisement
