Please Read; Please Read And Save These Important Safeguards; Important Instructions - Bionaire BCH9300 Instruction Manual

PLEASE READ

ENGLISH
PLEASE READ AND SAVE
THESE IMPORTANT
SAFEGUARDS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock, and injury to
persons, including the following:
1. Read all instructions before using the
appliance.
2. To avoid fire or shock hazard, plug the
appliance into the appropriate outlet.
3. The heater is hot when in use. To avoid
burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when
moving this heater. Keep combustible
materials, such as furniture, pillows, bedding,
papers, clothes, and curtains at least 0.9 m
(3') from the front of the heater and keep
them away from the sides and rear.
4. DO NOT run cord under carpeting. DO NOT
cover cord with throw rugs, runners, or the
like. Arrange cord away from traffic area and
where it will not be tripped over.
5. This heater is not intended for use in
bathrooms, laundry areas and similar indoor
locations. NEVER place heater where it may
fall into a bathtub or other water containers.
6. Always unplug the heater when not in use.
7. When unplugging, be sure to pull by the plug
and not the cord.
8. DO NOT insert or allow foreign objects to
enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or
damage the heater.
9. DO NOT operate heater with a damaged
cord or plug, or after the heater malfunctions,
has been dropped or damaged in any
manner. Take appliance to Authorized
Service Center for examination, electrical or
mechanical adjustment, or repair.
10. A heater has hot and arcing or sparking
parts inside. DO NOT use it in areas where
gasoline, paint, or flammable liquids are
used or stored.
11. Use appliance only for intended household
use as described in this manual. Any other
use not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons. The use of attachments not
recommended or sold by the manufacturer
may cause hazards.
12. DO NOT use outdoors.
BCH9300_12MLM1.indd 3-4
13. To prevent a possible fire, DO NOT block air
intakes or exhaust in any manner. DO NOT
use on soft surfaces, like a bed, where
openings may become blocked.
14. To disconnect heater, turn controls to the OFF
position, then remove the plug from outlet.
15. Avoid the use of an extension cord because
the extension cord may overheat and cause
a risk of fire.
16. DO NOT attempt to repair or adjust any
electrical or mechanical functions on this
unit. Doing so will void your warranty. The
inside of the unit contains no user
serviceable parts. All servicing should be
performed by qualified personnel only.
17. Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if
plug or outlet is hot to touch.
18. If the heater will not operate, see specific
instructions on Auto Safety Shut-off.
19. WARNING: In order to avoid overheating, do
not cover the heater ( ).
20. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
21. Close supervision is necessary when any
appliance is used by or near children, or
incapacitated individuals.
PLEASE SAVE THESE
INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
NOTE: A Phillips screwdriver is required for
assembly.
Unpack your heater from the box, being careful
to remove all parts from plastic bags and
remaining packaging. Please save the carton for
off-season storage.
This model is packed with separate base in the
box. Carefully remove all parts from plastic bags.
To prevent scratches, place all parts onto a cloth
before assembly. Follow the below instructions
for Base assembly:
Base Assembly
Step 1: Snap the two halves of the base
together and run the power cord
through the center of the base. Line up
holes of the base with holes on bottom
of heater housing, and secure with 4
2
provided screws. (Refer to Figure 1)
Step 2: Lace the power cord through the cord
minders on the underside of the base.
(Refer to Figure 2)
Step 3: Turn the heater right side up on a flat
level surface prior to beginning
operation. (Refer to Figure 3)
Remote Control
Your heater comes with a remote control, unpack
the remote control from box. This unit requires
two (2) AAA batteries, 1.5V (not included). Please
note this remote control will not work through
walls.
Battery Replacement
a) Remove battery cover from remote control.
b) Remove batteries from the remote control.
c) Insert two new batteries, pressing them
firmly into their slot.
d) Replace the battery cover.
Figure 1 Power Cord
Rear
4 Base Securing
Base
Screws
Front Base
Power cord
Figure 2
Figure 3
Control Panel
Remote Control
Assembled
Base
Figure 4
H
G
B
F
C
E D
A LCD Display
E B Oscillation Button
G C Thermostat Button
D
D Timer Button
C
E Fan Only Button
B
F Heat & $ave
TM
Button
G Power Button
H Indicator Lights
3
4/25/12 9:46 AM
A