Page 2
I. Safety Instructions The l ig h tn i ng fla sh w i th arro wh e ad symb ol , within an equilatera l triangle, is intended to alert CAUTION the user to the presence of uninsulated “ dangerous voltage”...
Page 3
PRODUCT SAFETY NOTICE 4. Completely discharge the high pote ntial voltage of the picture tube before handli ng. The pi cture tube is a Many e lectrical an d mechanica l parts in this TV vacuum and if bro ken, the gl ass will explode. receiver have special safety-related characteristics.
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Product Specification CMO V320B1-L01 1.1 VIDEO SECTION MK8202 Display size 32”/16:9 Display Resolution 1366 X 768 510.75µm (H) x 510.75µm (V) Pixel Pitch Peak Brightness 550(nits) Contract Ratio 1000:1, Typical (1/100 White Window, Dark Room) View Angle Hor.
Page 5
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Stereo Decode MTS with SAP Power Rating AC 120V, 60Hz ≤200W Power Consumption 1.6 Support the Signal Mode This machine can support the different from VGA signal mode in 6 kinds...
Page 6
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Technical Data AC 120V, 60Hz Remote control Battery 3V (UM- 3/R6P/AAA×2) 2. TV system TV System NTSC M ATSC Stereo Decode MPEG-2 Closed Caption/V-Chip Channel 181 CH 2-69 CH 3. Intermediate Picture 45.75MHz...
Page 7
Remote Control Power ( ): Press to turn on and off. Mute ( ): Press to mute the sound. Press again or press VOL+/- to restore the sound. CCD: Press to select the Closed Caption mode. V-Chip: Press to select the child protect mode. MTS: Press repeatedly to cycle through the Multi-channel TV sound (MTS) options: Mono, Stereo and SAP (Second Audio Program).
Page 8
Menu: Press to enter on-screen setup menu, press again to exit. : Press to search the backward or forward. : Press to play or pause the DVD disc. : Press to stop playing the disc. : Press to skip the backward or forward.
Page 9
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Attachment 1 Electrical & Optical Specification : Items Instruction Typical Limit Unit Video sensitivity For 30dB S/N ≤51 dBuV FM sound sensitivity For 30dB S/N ≤35 dBuV Color sensitivity For RF transmission ≤40...
Page 10
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Max Audio Output Power 7×2 5.0×2 ≥ Audio output power 1KHz 10% THD 6×2 ≥ 4.0×2 10% THD ≤ Po=0.5W ≥ Signal to buzz ratio coeighting Minimum volume hum coeighting ≤...
Page 11
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE Reference No : LCT3201AD Test Condition All tests shall be performed under the following conditions unless otherwise specified Picture Modulation 87.5% Sound Modulation 27KHz Dev. For DK/I/BG 15KHz Dev. For M/N Picture to Sound Ratio...
Page 12
DVD player's spec. For LCD-TV Combo Division Section Remarks name AKAI Marketing Area( setup default language) General Power supply +5v,+3.3v Power Consumption Manufactruer of Loader mechanism Foryou DL06-LS Opitical Pick UP Sanyo HD-62/65 DVD Module Chipset used MTK 1389FE Playback...
Page 14
UART0 (Communication with MT5351) Video[0...23] data audio signal 74LVC244A control signal From MT5351 U30-U33 (BUFFER) Video/audio signal control signal TMDS0~3 I2C(MT8202I2C) MT8293 HDMI Receiver HDMIPLUG_PWR HDMI (U25) LVDS Data TO PDP/LCD Connector HDMI_I2C Connector MT8202 Control Signal EEPROM UPA672T EEPROM 24C02 (U34) 24C04...
Page 15
Combo DVD 4334KSZ L/R output Audio DAC 16M Flash YPbPr output 3.3V IR Input MT1389FE AM5888 MPEG decoder Optical Pick Up & Servo System SL/F & Motor EEPROM Motor Driver 64M SDRAM...
Page 16
Parts Position DVD Combo Power Board Key Pad DTV Board ATV Board Main Board Power Switch Speaker Speaker Stand...
Page 42
Main IC Specifications - M13S128168A (ESMT) 2M x 16 Bit x 4 Banks Double Data Rate SDRAW - MT5111CE Single-Chip HDTV/CATV Demodulator - MT5351 MT5351 is a DTV Backend Decoder SOC which support flexible transport demux, HD MPEG-2 video decoder, MPEG1,2, MP3, AC3 audio decoder, HDTV encoder. MT5351 is powered by ARM 926EJ with 16K I-Cache and 16K D-Cache.
Page 43
Date : 2005.10.13 CPT TFT-LCD CLAA320WA01 ACCEPTED BY: TENTATIVE APPROVED BY CHECKED BY PREPARED BY TFT-LCD Product Planning Management General Division Doc.No: Issue Date: 2005/10/13 CLAA320WA01 C-Tentative-Ver 2.0-20051013 T- 3650002- 000- A NEW...
Page 44
RECORD OF REVISIONS Revision Date Page Description Ver1.0 2005/8/29 Preliminary specification was first issued. Module Weight = 8000(Max)→8200(Max) Input Voltage of Inverter =21.6 (Min)→ -0.3(Min) Input Voltage of Inverter =26.4 (Max)→27 (Max) Inverter Dimming=0 (Min)→ -0.3(Min) Inverter Dimming=5(Max)→5.5(Max) Backlight on Control Voltage=2(Min)→ -0.3(Min) Backlight on Control Voltage=5(Max)→5.5(Max) LCD Power Supply Current—White=400(Typ.)→350(Typ.) LCD Power Supply Current—White= -- (Max)→400(Max)
1. OVERVIEW CLAA320WA01 is 32” color (80.04cm) TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, LVDS driver ICs, control circuit, backlight, and inverter. By applying 8 bit digital data, 1366*768, 16.7 million-color images are displayed on the 32” diagonal screen.
2. ABSOLUTE MAXIMUM RATINGS The following are maximun values which, if exceeded, may cause faulty operation or damage to the module. ITEM SYMBOL MIN. MAX. UNIT REMARK Power Supply Voltage For LCD - 0.3 15.0 Input voltage of inverter - 0.3 Inverter dimming VDIM - 0.3...
3. ELECTRICAL CHARACTERISTICS Ta=25℃ 3.1 TFT-LCD MODULE ITEM SYMBOL MIN UNIT REMARK 11.4 12.0 12.6 LCD Power Supply Voltage Ripple Voltage Vrpd mVp-p VIN=+12.0V Rush current Irush White LCD Power Black Supply Current RGB stripe 6.48 LCD power consumption High input voltage of LVDS Low input voltage of LVDS Input common voltage of 1.25...
Page 49
*3) The specified power supply current is under condition at Vcc=12V, Ta=25+/-2℃, f =60Hz, whereas a power dissipation check pattern below is displayed. a. White pattern b. Black pattern c. RGB Stripe pattern *4) Power and Signal Sequence: VCC:12V Power Supply (VCC:12V) Interface Signal (LVDS Data with H,Vsync...
Page 50
VCC-dip State: 1) When 9V VCC <11.4 V, td 10 ms. ≦ ≦ 2) VCC > 11.4V, VCC-dip condition should also follow the VCC-turn-off condition. 11.4V *5) LVDS Signal Definition: VID = VIN – VIN-, VCM = –VCM-|, △ |VCM VID = –VID-|, △...
Page 51
Ta=25℃ 3.2 BACKLIGHT ITEM UNIT REMARK SYMBOL Lamp Voltage 1150 Vrms IL=5.0mA Lamp Current mArms Lamp life time 50,000 Input voltage of inverter 21.6 26.4 IIN0 (4.8) Input current of inverter (4.4) Input frequency of inverter 61.5 63.5 65.5 Inverter dimming VDIM Inverter duty ratio VDIM=5V(MAX.)
Page 52
*2) Definition of the lamp life time: When lamp luminance redue to 50% or lower than its initial value. *3) Ripple voltage that occur at the instant of power-on can’t exceed 30V. *4) 25°C; V = 5V(MAX.), After power on for 5 seconds *5) 25°C;...
5. INTERFACE TIMING (DE only mode) 5.1 TIMING SPECIFICATION ITEM SYMBOL MIN. TYP. MAX. UNIT Freq. DCLK Cycle 14.7 12.5 11.9 Line Rate 37.1 48.6 Horizontal 1575 1648 1936 Total Time Horizontal Horiaontal 1366 1366 1366 Effective Time Horizontal Blank Time DENA Frame Rate Vertical...
5.2 TIMING CHART a. Horizontal Timing DCLK First Data DATA Invalid Data 1365 1366 Invalid Data (R,G,B) Last Data DENA =1/f Hsync hsync hsync b. Vertical Timing Chart Invalid Data Invalid Data LINE DATA DENA =1/f Vsync vsync vsync...
Page 58
5.3 LVDS DATA MAPPING a. None-JEIDA normal Specification 1CLK RXCLK RXIN0 RXIN1 DENA Hsync Vsync RXIN2 RXIN3 Preserve PREVIOUS DATA for current CLK cycle NEXT b. JEIDA Specification 1CLK RXCLK RXIN0 RXIN1 RXIN2 DENA RXIN3 Preserve PREVIOUS DATA for current CLK cycle NEXT 8bit LSB: R0,G0,B0 Parallel TTL Data Inputs Mapped to LVDS outputs...
Page 60
5.5 COLOR DATA ASSIGNMENT [Note] 1) Definition of gray scale: Color (n): n indicates gray scale level, higher n means brighter level. 2) Data: 1-High, 0-Low...
8.OPTICAL CHARACTERISTICS Ta = 25°C, VCC=12V ITEM MIN. TYP. MAX. UNIT SYMBOL REMARKS CONDITION θ = ψ﹦0° Contrast (CEN) 1000 *1)*2)*3) Point-5 Central θ = ψ﹦0° cd/m luminance Luminance θ = ψ﹦0° Luminance cd/m *2)*3) (AVG) θ = ψ﹦0° Uniformity *2)*3) △...
Page 66
Definition of these measurement items is as follows: *1) Definition of Contrast Ratio: [ These items are measured using BM-5A (TOPCON) under the dark room condition (no ambient light). ] CR=ON (White) Luminance/OFF (Black) Luminance *2) Definition of Luminance, Luminance uniformity, Contrast, and the Deviation of Color Coordinate: Luminance and Contrast: To measure at the center position “5”...
Page 67
*3) Definition of Viewing Angle ( θ, ψ Figure 8-2. Definition of Viewing Angle *4) Definition of Response Time ( White – Black ) White(255 Luminance Black(0) Figure 8-3. Definition of Response Time ( White – Black ) *5) Definition of Response Time ( Gray to Gray, Average ) (0~255 Luminance (Gray Scale Level)
Page 68
The driving signal time means the signal of gray level 0, 31, 63, 95, 127, 159, 191, 223, 255. Gray to gray average means the average switching time of gray level 0, 31, 63, 95, 127, 159, 191, 223, 255 to each other. The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature change during measuring.
Page 69
*7) Definition of Cross talk Ratio CMR = MAX ( ( | ( LB1-LA ) / LC | ) × 100 ﹪ ﹪ , ( | (LB2 – LA ) / LC | ) × 100 LA: Pattern A (Half-Tone pattern) Measure point Luminance LB1, LB2: Pattern B1, Pattern B2 Measure point Luminance LC: Pattern C (white pattern) Measure point Luminance Pattern B1...
9.RELIABILITY TEST CONDITIONS 9.1 TEMPERATURE AND HUMIDITY TEST ITEMS CONDITIONS High Temperature Operation 50 ; 240hrs ℃ High Temperature Storage 60 ; 240hrs ℃ High Temperature 50 ; 90% RH; 240 hrs ℃ High Humidity Operation (No condensation) Low Temperature Operation 0 ;...
11. HANDLING PRECAUTIONS FOR TFT-LCD MODULE Please pay attention to the followings in handling TFT-LCD products. 11.1 ASSEMBLY PRECAUTION (1) Please use the mounting hole on the module side in installing and do not beading or wrenching LCD in assembling. And please do not drop, bend or twist LCD module in handling. (2) Please design display housing in accordance with the following guidelines.
Page 74
(9) Please pay attention to handling lead wire of backlight so that it is not tugged in connecting with inverter. 11.2 OPERATING PRECAUTIONS (1) Please be sure to turn off the power supply before connecting and disconnecting signal input cable. (2) Please do not change variable resistance settings in LCD module.
Page 75
11.6 OTHERS (1) A strong incident light into LCD panel might cause display characteristics' changing inferior because of polarizer film, color filter, and other materials becoming inferior. Please do not expose LCD module direct sunlight Land strong UV rays. (2) Please pay attention on the side of LCD module do not contact with other materials in preserving it alone.
Page 80
If you forget your V-Chip Password - Omnipotence V-Chip Password: 8202. Using the “Change Password” item When enter the “V-Chip” menu, select “Change Password”. Press ▲ or ▼ button to highlight the “Change Password” item. Press Enter button to confirm and pop up a menu. Use 0~9 buttons input the omnipotence password(8202), then Press Enter button to enter and pop up a menu.
Software Upgrade Process of update MT8202 Preparing : 1. Connect RS232-VGA download line, One connector is connected to VGA connect port of Plasma TV ,while another side is connected to PC COM port. 2. Store the MtkTool into the PC . Downloading : 3....
Page 82
6. Choose the bit rate as 115200. 7. Select the update binary by pressing browse button. For exemple,the binary file name is (this update firmware will be sent to your side) PDP4210EA1_V09.bin. 8. Press Upgrade button and start update process.
Page 83
9. The update process is successful as the progress bar is 100%. After the update process is ok,...
Page 84
turn off power and wait indicator light is off. Turn on power and TV can work. Checking It is needed to check the version of the firmware for MT8202 which has been download into the Plasma TV . Press Menu button of the remote control,following input “8202”of the remote control and OSD menu for Factory Setting is appeared on the screen .
Page 85
5. (please try to check the COM port of your PC). Select current COM port. 6. Choose the bit rate as 115200. Select the update binary by pressing browse button. For exemple,the binary file name is 7....
Page 86
(this update firmware will be sent to your XXXX_PDP4210EA1_000000XX_X_P.bin. side) 8. Press Upgrade button and start update process.
Page 87
9. The update process is successful as the progress bar is 100%. After the update process is ok, turn off power and wait indicator light is off. Turn on power and TV can work. Checking : It is needed to check the version of the firmware for MT5351AG which has been download into the Plasma TV .