NTRODUCTION Thank you for selecting a Martin Mania PR1. The Mania PR1 is a gobo projector with a motorized rotating gobo. S A F E T Y I N F O R M A T I O N Warning! This product is not for household use. It presents risks of lethal or severe injury due to fire and heat, electric shock, and falls.
Page 5
The lamp shall be changed if it becomes damaged or thermally deformed. If the external power cord of this luminaire is damaged, it shall be replaced by a special cord exclusively available from your Martin dealer. Avoi di ng electric shocks...
U N P A C K I N G The packing material is carefully designed to protect the fixture during shipment - always use it to transport the fixture. The Mania PR1 is packaged with the following: • 3-wire IEC power cable • User manual •...
Martin dealer. Configuring for local mains power The Mania PR1 has a switch-selectable power supply that can operate in the following voltage ranges at 50-60 Hz: • 115 - 120 volts (setting 115) •...
2 Turn the power on using the mains switch. O V E R H E A D M O U N T I N G The Mania PR1 is designed to be hung overhead with a clamp (not included). Mania PR1 user manual...
Page 9
Always use a secure means of secondary attachment. For indoors use only. To hang the Mania PR1 on an overhead support: 1 Verify that the structure can support at least 10 times the weight of all installed fixtures, clamps, cables, auxiliary equipment, and other items.
40 mm (1.6 in.). To change the gobo/texture glass: 1 Switch the mains power off and allow the fixture to cool for 20 minutes. 2 Unscrew the gobo access hatch on the top of the fixture. Mania PR1 user manual...
Page 11
3 Lift the gobo holder out of the fixture. 4 The gobo/texture glass is held in place by a steel spring. Remove the spring to remove the gobo/texture glass that is presently installed. Lamp side Front lens side 5 Install the replacement gobo or textured glass. Note that the coated or textured side should face the lamp.
F O C U S I N G T H E M A N I A P R 1 The focus is adjusted using the dial next to the lens. Twist the dial until a sharp image is acquired. Mania PR1 user manual...
R E M O T E C O N T R O L O P E R A T I O N The remote control unit can control up to four daisy- chained Mania PR1s. Connect the remote control to the RJ-45 In connector on the first Mania PR1 fixture Rotation speed Rotation speed and connect successive fixtures using the RJ-45 Out connector.
C L E A N I N G Regular cleaning of the elements in the optical path, as well as the air vents, is vital to maintaining the operational quality of the Mania PR1. Important! Excessive dust, smoke fluid, and particulate buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty.
2 Remove the thumb screw holding the cover in place. 3 Slide the fixture cover open. 4 Vacuum or gently blow away dust and loose particles with compressed air. 5 Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water.
Page 16
4 Gently grasp the bulb as close to the base as possible and lever it out of the bulb socket. 5 Replace the bulb; only the EVC (M33) 24V / 250 watt lamp is supported (Martin P/N 97000103). Warning Installing any other lamp may damage the fixture! Mania PR1 user manual...
R E P L A C I N G T H E M A I N S F U S E The Mania PR1 uses a time-delay fuse for protection against current overload. An indication that the fuse may have blown is that when power is applied and the lamp is switched on, no light is produced.
Burned out lamp Install new lamp Fixture to hot Allow to cool Improve air flow around fixture No action Electrical malfunction Refer to a Martin service technician Fuse blows repeatedly Electrical malfunction Refer to a Martin service technician Mania PR1 user manual...
PECIFICATIONS P H Y S I C A L Size without mounting bracket (LxWxH) ..340x290x158 mm (13.4x11.4x6.2 in.) Weight..........9 kg (19.8 lbs) C O N S T R U C T I O N Housing.