Page 1
IMI CORNELIUS INC g One Cornelius Place g ANOKA, MN 55303–6234 Telephone (800) 238–3600 Facsimile (800) 535–4231 Installation Manual “I” Series 224 Ice Cube Machine IMPORTANT: TO THE INSTALLER. It is the responsibility of the Installer to ensure that the water supply to the...
SAFETY INFORMATION Recognize Safety Information This is the safety-alert symbol. When you see this symbol on our machine or in this manual, be alert to the potentially of personal injury. Follow recommended precautions and safe operating practices. Understand Signal Words DANGER A signal word - DANGER, WARNING, OR CAUTION is used with the safety-alert symbol.
Page 4
THIS PAGE LEFT BLANK INTENTIONALLY 630460070...
4. All claims for loss or damage should be filed at once. Delays in filing will reduce the chance of achieving a satis factory resolution to the claim. SPECIFICATIONS, ICE CUBER The following table contains equipment specification information for the Ice Cubers. MODEL IACS224 IACS224E50 IWCS224 IWCS224E50 UNIT...
Page 6
(Air-Cooled Systems only) or CONDENSER FAN MOTOR (Water-Cooled and Remote Systems only) AIR CIRCULATION FAN MOTOR Volts Phase Hertz Amps Running Watts WATER PUMP Volts Phase Hertz Amps Running 1/60 1/50 1/60 1/50 630460070...
INSTALLATION This section covers unpacking and inspection, selecting location, installing Unit, preparing for operation, and operation. Installation and start-up of the equipment should be performed by the distributor or the dealer’s professional staff. LOCATION OF EQUIPMENT For maximum performance the location should be away from heat sources such as ovens, direct sunlight, hot air discharge, etc.
ELECTRICAL 1. All wiring and connections must conform to national and local electrical codes. 2. Wire size and circuit protection must conform to specifications and cuber must be on a separate electrical circuit. 3. Cuber must be grounded for the safety requirements. 4.
START-UP AND CHECK OUT 1. Turn the cuber’s power switch to the clean (pump only) position. The water pump only should be operation- al. Check for an even, steady flow of water over the evaporator top extrusion and down over evaporator surface.
OWNER-OPERATOR The installation is not complete until you are sure the owner-operator understands the cuber operation and his or her responsibility of preventative maintenance. Does the owner-operator know: 1. Location of electrical disconnect switch and water shut-off valves? 2. How to start and/or shut down the product, clean and sanitize it.? 3.
6. After third rinse cycle, place product power switch in ON position. Allow product to produce one slab of ice—DISCARD THE ICE. 7. When clean cycle is complete, return cuber to normal operating mode. NOTE: Please take not of the following: S Ice machines should only be cleaned when needed, not by a timed schedule of every 60 days, etc.
Figure 6 shows the setting of circuit board. There are dump cycle dip switch (S3) and curtain selection dip switch (SW4) in the circuit board. Even though no water curtain equipped in IACS224 and IWCs224, “single cur- tain connection” on SW4 need to be selected.
Harvest Voltage Set point pins 2 and 3 Factory setting @ 1.224 V External Error LED Condenser Sensor Connection Suction Line Sensor Error Bridge thickness pot. Dump S3-1 S3-2 OFF Dump Every Harvest (FACTORY SETTING AS RECEIVED) OFF Dump Every Third Harvest S3–2 S3–1 Dump Every Seventh Harvest...
1. Thinner Bridge - Turn the ice thickness “pot” adjustment screw Ø CW one full turn.. Allow two cycles be- fore determining if additional adjustments are required. 2. Thicker Bridge - turn the ice thickness “pot” adjustment screw Ù CCW on full turn. Allow two cycles before determining if additional adjustments are required.
The parts warranty period is three years (36 months) from the date of installation or 39 months from the date of shipment by CORNELIUS whichever time period elapses first. With respect to compressor, solid state control board and the evaporator(s), the warranty period will be five years (60 months) from the date of installation or 63 months from the date of shipment by CORNELIUS whichever time period elapses first.
Page 17
THIS PAGE LEFT BLANK INTENTIONALLY 630460070...
Page 18
IMI CORNELIUS INC. Corporate Headquarters: One Cornelius Place Anoka, Minnesota 55303-6234 Telephone (800) 238-3600 Facsimile (763) 422-3246...