ARRI ARRIFLEX 416 Quick Manual
Hide thumbs Also See for ARRIFLEX 416:

Advertisement

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ARRIFLEX 416 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ARRI ARRIFLEX 416

  • Page 1: Table Of Contents

    Camera Right & Back Quick Specs Power On, Camera RUN, Inching, Camera Display Loading the Magazine Mounting the Magazine Changing fps & Shutter Angle Beeper, Backlight & RGB ARRIGLOW On-board Battery OBB-2 Integrated Video System Accessories Timecode Operation ARRI Group Addresses 05/2006...
  • Page 2 This page is left blank intentionally. ARRIFLEX 416 Quick Guide 05/2006, Page 2...
  • Page 3: About, Software, Tools, Safety

    This Quick Guide (order number K5.40076.0) provides a short introduction to the ARRIFLEX 416. This guide does not replace the ARRIFLEX 416 User’s Guide (K5.40077.0). It is essential that you acquaint yourself with the user’s guide before operating the equipment.
  • Page 4: Camera Left & Front

    MODE SEL/∆ SET/ V PHASE button Display 416 Shoulder Magazine 120/400 RUN button RUN Indicator Image rotation knob Tape hook PL lens port (Super 16 only) Front 3/8 – 16 mounting point ARRIFLEX 416 Quick Guide 05/2006, Page 4...
  • Page 5: Camera Right & Back

    Power on/off connector rosette switch connectors connectors Pitch indicator adjust button Eyepiece rotation friction IVS ground fault indicator MINI MONITOR connector BNC connectors Magazine fi lm Power connector reserve counter (BAT) REMOTE connector ARRIFLEX 416 Quick Guide 05/2006, Page 5...
  • Page 6: Quick Specs

    LWZ-1, ARRI/Zeiss Standard Speed lenses, ARRI/Zeiss Super Speed lenses, ARRI/Zeiss Ultra Prime lenses, ARRI/Zeiss Master Prime lenses, Cooke S-4 lenses, ARRI Macro lenses, Cooke & Angenieux zoom lenses, ARRI/Zeiss Variable Prime lenses. Not compatible with: 16SR magazines, 16SR on-board batteries, 435 Single Frame Hand Controller, CCU and ARRICAM electronic accessories.
  • Page 7: Power On, Camera Run, Inching, Camera Display

    Turning Camera Power On The Power On button for the ARRIFLEX 416 is located above the RUN button on the camera right side. To turn the camera On, briefly press the Power On button. When a battery is connected to the camera and the power switch is turned on, you should see characters appear on the Display on the camera left side.
  • Page 8: Loading The 416 Magazine

    • Flip the magazine over lengthways so the take-up door is uppermost and the top of the magazine is facing you. The ‘ARRI’ on the door will be upside down. • Open the take-up side magazine door and latch back the footage counter roller arm. Fit an empty film core to the take-up core holder.
  • Page 9 • If using timecode, set the sensitivity switch according to the table on page 19 of this guide. The switch is located at the top left corner of the feed side door. Incorrect ARRIFLEX 416 Quick Guide 05/2006, Page 9...
  • Page 10: Mounting The Magazine

    • Inch the camera by briefly pressing the PHASE button. Note: When a magazine is first mounted and PHASE or RUN is pressed, the display shows ‘loop’, while the camera performs a short routine that centralizes the film loop. ARRIFLEX 416 Quick Guide 05/2006, Page 10...
  • Page 11: Changing Fps & Shutter Angle

    • Turn the 416 Shutter Tool until the desired Mirror Shutter preset angle is reached. Angle presets are: 180º, 172.8º, 150º, 144º, 135º, 90º & 45º. Turning counter-clockwise reduces the angle. ARRIFLEX 416 Quick Guide 05/2006, Page 11...
  • Page 12: Beeper, Backlight & Rgb Arriglow

    SEL button will now cycle through the red (r), green (G) and blue (b) values of the user colour. Pushing the SET button changes the flashing colour value from 0 (no colour) up to 16 (maximum colour). ARRIFLEX 416 Quick Guide 05/2006, Page 12...
  • Page 13: On-Board Battery Obb-2

    When an OBB-2 is connected, display mode 3 can additionally show battery capacity or magazines left. Note: The new 416 power connector on the camera remains compatible with standard ARRI 24 volt power cables. Mounting the OBB-2 •...
  • Page 14: Integrated Video System

    Open the video lens IRIS fully and use either Automatic Gain Control or Manual Gain Control to control the image brightness. Only use the video lens IRIS if the brightness exceeds the electronic control range. ARRIFLEX 416 Quick Guide 05/2006, Page 14...
  • Page 15 To assist in setting up attached video monitors, the 416 IVS has the option to generate colour bars. • Press and hold the ENTER/INSERT button for 3 seconds to enter the on-screen menu. • In the WB/GAIN/BARS sub-menu, set COLOR BARS to ON. ARRIFLEX 416 Quick Guide 05/2006, Page 15...
  • Page 16: Accessories

    Accessories ARRIFLEX 416 Quick Guide 05/2006, Page 16...
  • Page 17 Accessories ARRIFLEX 416 Quick Guide 05/2006, Page 17...
  • Page 18: Timecode Operation

    Timecode Operation Note: To write SMTPE timecode to film, ARRIFLEX 416 magazines must have the 416 Timecode Module fitted. Note: Timecode recording is only possible at the 5 Standard Speeds of 23.976, 24, 25, 29.97 & 30 fps. Turning Timecode Recording On and Off.
  • Page 19 (Color Negative) TCS 5 Kodak 7293 (Color Negative) TCS 5 Kodak 7296 (Color Negative) TCS 5 Kodak 7297 (Color Negative) TCS 6 Kodak 7298 (Color Negative) TCS 5 Kodak 7620 (Color Negative) TCS 6 ARRIFLEX 416 Quick Guide 05/2006, Page 19...
  • Page 20: Arri Group Addresses

    ARRI Group Addresses Australia ARRI Australia PTY Limited (Sales, Service & Rental) Unit 6C, 5 Talavera Road, Macquarie Park, Sydney. NSW 2113, Australia Voice phone: +61 (2) 9855 4300, FAX: +61 (2) 9855 4301 Email: info@arri.com.au Canada ARRI Canada Limited (Sales & Service) 415 Horner Ave.

Table of Contents

Save PDF