Do you have a question about the A17214H Cruiser and is the answer not in the manual?
Questions and answers
RHONDA SEYMOUR
April 26, 2025
MY LITTLE WHEEL IS PUSHED UP AGAINST THE REAR WHEEL
1 comments:
Mr. Anderson
May 13, 2025
If the little wheel on your COX A17214H Cruiser is pushed up against the rear wheel, check the tyre pressures first. Uneven tyre pressure can cause misalignment or contact between wheels. Ensure the front wheel is inflated to approximately 140 Kpa (20 psi) and the rear wheel to 105 Kpa (15 psi) for 8.50x8 tyres or 90 Kpa (13 psi) for 9.50x8 tyres. Adjust as needed to prevent uneven contact or damage.
CODE_____________ DATE OF PURCHASE:__________________________________ ISSUED TO: OWNERS NAME: ADDRESS: TOWN/CITY: STATE: ISSUED BY: AUTHORISED COX DEALER/ DISTRIBUTOR: ADDRESS: TOWN/CITY: STATE: PRE DELIVERY CHECK LIST Check parts Assemble Service Instruction ALWAYS KEEP THIS MANUAL IN A SAFE PLACE.
SAFETY INSTRUCTIONS Read, understand, & follow all instructions in It is advisable to wear suitable eye protection the Owner/Operators manual. when operating a mower. Know the controls and how to stop the Mow only in daylight or good artificial light. engine quickly in an emergency.
Page 4
PRE-DELIVERY INSTRUCTIONS INTRODUCTION: Drive Lever Switches - With Cutter PTO switch in DISENGAGED position and Clutch/Park The purpose of this procedure is to ensure the Brake Lever set in the ON position and the Drive dealer/distributor made necessary Levers in the DRIVE position. installations, adjustments and checks, before the Attempt to start the engine.
Page 5
PRE-DELIVERY INSTALLATION OF SEAT AND CONTROL LEVERS 22 January 2016 Cruiser Model A17214H rev 3 081015 Page 5...
Unleaded fuel is recommended by all manufacturers of To slow down when driving forward pull both drive control engines fitted to Cox products (up to 10% ethanol blended levers back. unleaded fuel is acceptable). To slow down when driving in reverse push both drive SAFETY SWITCHES control levers forward.
5/8” UNF NUT 100Nm (74lbf ft) We are proud that you have purchased a Cox product and urge you to follow these instructions to obtain the maximum life for your machine. If in doubt check with your supplier. 22 January 2016...
MAINTENANCE SCHEDULE BEFORE EACH USE Check engine oil level, adjust if required Check tyre pressures, adjust if required Check engine air cleaner foam pre-cleaner, service if required Check for loose fasteners, tighten if required Check engine rotating screen/finger guard, clean if required Check cutting attachment cutter blades, bolts, nuts, housing and Check operation of safety switches, service if required guards for wear or damage, replace if required...
Page 9
12 MONTHS OR 100 HOURS which ever occurs first Change engine oil filter Check for loose fasteners, tighten if required Change engine oil Check operation of safety switches, service if required Check engine spark plug, clean, adjust, or replace if required Check tyre pressures, adjust if required If fitted clean engine exhaust spark arrester Check mowing attachment cutter blades, bolts, nuts, housing and...
Page 10
27 MONTHS OR 225 HOURS which ever occurs first Change engine oil if operating under heavy load or high ambient Check tyre pressures, adjust if required temperature Check mowing attachment cutter blades, bolts, nuts, housing and Check engine air cleaner foam pre-cleaner, service if required * guards for wear or damage, replace if required Check engine rotating screen/finger guard, clean if required * Check for loose fasteners, tighten if required...
Page 11
22 January 2016 Cruiser Model A17214H rev 3 081015 Page 11...
Page 12
BODY OUTER COMPONENTS before serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2348-7102, CZP2442-2171, CZP2448-257 Page 12 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 13
BODY OUTER COMPONENTS before serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2348-7102, CZP2442-2171, CZP2448-257 ITEM PART NUMBER DESCRIPTION A172011R Floor, Removable A172003R Frame, Footrest A120908R Lid, Storage A120805 Non-Skid, Footrest, ZTR, 460x210 96114 Strap, Bonnet PR04M4.8 Rivet NCM6X1.6X9.5 Nut, Cage, M 6, 1.6 Panel, 9.5sq Hole A120918R Bumper, Front NCM8X3.2...
Page 14
BODY OUTER COMPONENTS from serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2348-7102, CZP2442-2171, CZP2448-257 Page 14 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 15
BODY OUTER COMPONENTS from serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2348-7102, CZP2442-2171, CZP2448-257 ITEM PART NUMBER DESCRIPTION A172011R Floor, Removable, Red A172003R Frame, Footrest, Red A120908R Lid, Storage, Red A120805 Non-Skid, Footrest, 460x210 96114 Strap, Bunji Loop PR04M4.8 Rivet NCM6X1.6X9.5 Nut, Cage, M 6, 1.6 Panel, 9.5sq Hole A120918R Bumper, Front NCM8X3.2...
Page 16
SEAT COMPONENTS Page 16 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 17
SEAT COMPONENTS ITEM PART NUMBER DESCRIPTION A120620R Mount, Seat, Red W052003 Washer 13060 Spring, Seat SH0516C Screw N05CN W05M202 Washer WS050216 Washer, Lock, Spring SP1PNCSM Switch, Plunger A120854 Kit, Armrest, T-Suit V-3505 Seat Screw, Pan, Cross Recess, Unc, 5/16"X 3/4", Black Armrest, Right Armrest, Left A120850...
Page 18
ENGINE AUXILLARY COMPONENTS 16HP HONDA 42” Cut Page 18 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 19
ENGINE AUXILLARY COMPONENTS 16HP HONDA 42” Cut ITEM PART NUMBER DESCRIPTION Engine, 16.0 Hp, V2cyl, HON, GXV530 A120660 Tank, Fuel, 11 L, Right AM293 Petrol Tap AM294 Grommet CF01 Cap, Fuel A120661 Tank, Fuel, 11 L, Left AM293 Petrol Tap AM294 Grommet CF01...
Page 20
ENGINE AUXILLARY COMPONENTS 22HP & 24HP B&S 42” Cut Only before serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2442-2171 Page 20 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 21
ENGINE AUXILLARY COMPONENTS 22HP & 24HP B&S 42” Cut Only before serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2442-2171 ITEM PART NUMBER DESCRIPTION A120660 Tank, Fuel, 11 L, Right AM293 Petrol Tap AM294 Grommet CF01 Cap, Fuel A120661 Tank, Fuel, 11 L, Left 80037 Grommet A120514...
Page 22
ENGINE AUXILLARY COMPONENTS 22HP & 24HP B&S 42” Cut Only from serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2442-2171 Page 22 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 23
ENGINE AUXILLARY COMPONENTS 22HP & 24HP B&S 42” Cut Only from serial numbers- CZP1642-3634, CZP2242-1151, CZP2342-1137, CZP2442-2171 ITEM PART NUMBER DESCRIPTION A120660 Tank, Fuel, 11 L, Right AM293 Petrol Tap AM294 Grommet CF01 Cap, Fuel A120661 Tank, Fuel, 11 L, Left 80037 Grommet A120514...
Page 24
ENGINE AUXILLARY COMPONENTS 24HP B&S 48” Cut Only before serial number- CZP2448-257 Page 24 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 25
ENGINE AUXILLARY COMPONENTS 24HP B&S 48” Cut Only before serial number- CZP2448-257 ITEM PART NUMBER DESCRIPTION 80037 Grommet A120514 Pulley, Engine A120660 Tank, Fuel, 11 L, Right AM293 Petrol Tap AM294 Grommet CF01 Cap, Fuel AM175 A120661 Tank, Fuel, 11 L, Left W06S Washer, Lock, Int Tooth, 3/8”...
Page 26
ENGINE AUXILLARY COMPONENTS 24HP B&S 48” Cut Only from serial number- CZP2448-257 Page 26 Cruiser Model A17214H rev 3 040815 22 January 2016...
Page 27
ENGINE AUXILLARY COMPONENTS 24HP B&S 48” Cut Only from serial number- CZP2448-257 ITEM PART NUMBER DESCRIPTION 80037 Grommet A120514 Pulley, Engine A120660 Tank, Fuel, 11 L, Right AM293 Petrol Tap AM294 Grommet CF01 Cap, Fuel AM175 A120661 Tank, Fuel, 11 L, Left W06S Washer, Lock, Int Tooth,3/8"...
Page 28
ENGINE AUXILLIARY COMPONENTS 23HP HONDA 42” Cut Only Page 28 Cruiser Model A17214H rev 3 040815 22 January 2016...
Need help?
Do you have a question about the A17214H Cruiser and is the answer not in the manual?
Questions and answers
MY LITTLE WHEEL IS PUSHED UP AGAINST THE REAR WHEEL
If the little wheel on your COX A17214H Cruiser is pushed up against the rear wheel, check the tyre pressures first. Uneven tyre pressure can cause misalignment or contact between wheels. Ensure the front wheel is inflated to approximately 140 Kpa (20 psi) and the rear wheel to 105 Kpa (15 psi) for 8.50x8 tyres or 90 Kpa (13 psi) for 9.50x8 tyres. Adjust as needed to prevent uneven contact or damage.
This answer is automatically generated