Advertisement

Operation Manual
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Losi, DSM and Nitrotane are trademarks or registered trademarks of Horizon Hobby, Inc.
Not responsible for errors.
Losi, a Division of Horizon Hobby, Inc.
Before operating this vehicle, please read all printed materials thoroughly.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 810 and is the answer not in the manual?

Questions and answers

Summary of Contents for Team Losi 810

  • Page 1 Operation Manual The Spektrum trademark is used with permission of Bachmann Industries, Inc. Losi, DSM and Nitrotane are trademarks or registered trademarks of Horizon Hobby, Inc. Not responsible for errors. Losi, a Division of Horizon Hobby, Inc. Before operating this vehicle, please read all printed materials thoroughly.
  • Page 2: Meaning Of Special Language

    Understanding that you are anxiously wanting to get AND a little or no possibility of injury. your 810 ready for the open road, it will be to your long CAUTION : Procedures, which if not properly followed, term benefit to make the effort and read through the create the probability of physical property entire manual.
  • Page 3: Getting Ready

    RC vehicle is not what you want—DO NOT • The top of the engine and the exhaust pipe are proceed and DO NOT run the 810. If the 810 has been run, extremely hot during and after use. Use caution not to your local hobby shop will not be able to process a return or touch these parts, especially when refueling.
  • Page 4: Batteries And Charging

    • Read all instructions provided by the manufacturer of the batteries. • Responsible adult supervision is necessary while charging batteries. • Always check to ensure the polarity of battery In addition to the tools included with the 810, you will find connection is correct. the following both useful and in some cases necessary. • Never leave batteries unattended while charging. • Small flat blade and Phillips screwdrivers •...
  • Page 5 The Losi 810 Overview Rear Shock Rear Camber Link Rear Sway Bar Battery Box Pull Start Throttle Linkage Throttle Servo Pressure Line Brake Linkage High-Speed Needle Valve Fuel Filter Air Cleaner On/O Switch Exhaust Pipe Radio Box Fuel Line Steering Link/Tie Rod...
  • Page 6 810 Radio System with Callouts AUXILIARY THROTTLE STEERING BIND Transmitter Steering Servo Receiver Throttle Servo Bind Plug...
  • Page 7: About The Radio

    Radio Operation The Losi DSM ® radio installed in the 810 is a state of the It is important that you familiarize yourself with the radio art system featuring the latest technology that requires system, as this is your direct link to the model.
  • Page 8: Binding The Radio System

    Binding the Radio System Steps to Re-Bind Ensure that the transmitter and vehicle are both turned off. Using the supplied Bind plug (which looks like a standard receiver plug with a wire loop installed) insert the Bind plug into the receiver slot labeled “BIND”. Looking down on the receiver this slot would be below the LED and is the farthest from the LED, or nearest to the corner of the receiver.
  • Page 9: Engine Tuning

    Engine Break-In and Adjustments Base Start-up Settings from the Factory High-Speed Needle—2 turns out from bottom The new Losi 3.4 engine in your 810 has been machined to tight tolerances and does not need an extended break-in. Low-Speed Needle—2 turns out from bottom...
  • Page 10 High-Speed Adjustment After initial acceleration, the engine should pull at a steady rate while maintaining a two-stroke whine and a noticeable trail of smoke. If the engine labors and is sluggish with heavy smoke, the mixture is too rich and needs to be leaned by turning the high-speed needle clockwise in one-hour Richer Leaner...
  • Page 11: Maintenance

    Do not run the 810 at dusk or in the dark when visibility is limited. Do not attempt to run this model if it will be out of sight for any amount of time.
  • Page 12 0-1 degree) will generally decrease steering and you may need to reset or make adjustments for better the 810 will feel easier to drive as a result. This is, most often, a driving performance. very critical adjustment in tuning your 810 that can be made quickly and easily.
  • Page 13 To raise the ride height, lower the shock adjuster nuts on the shock evenly on the end (front or rear) of the 810 that you are working on. To lower the ride height, raise the shock adjuster nuts. Both left and right nuts should be adjusted evenly.
  • Page 14 If your 810 needs a softer or firmer spring, change the Radio system does not work properly: spring. Do not think that simply moving the shock nuts will...
  • Page 15 If the engine will not turn over it is probably still new and bleed your 810 shocks. Note that if you are cleaning or and stuck at top dead center. Use a screwdriver to changing the fluid you will find the LOSA99217 Nitrotec ™...
  • Page 16: Warranty And Repair Policy

    Warranty and Repair Policy Warranty Period Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase by the Purchaser. Limited Warranty Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.
  • Page 17: Warranty Services

    Warranty Services United States (Electronics and engines) Horizon Service Center Questions, Assistance, and Repairs 4105 Fieldstone Rd Your local hobby store and/or place of purchase cannot provide Champaign, Illinois warranty support or repair. Once assembly, setup or use of the 61822 USA Product has been started, you must contact Horizon directly.
  • Page 18: Fcc Information

    No. HH20100823 sired operation. Caution: Changes or modifications not expressly approved by the Product(s): LOS 1/8 810 Buggy RTR party responsible for compliance could void the user’s authority to Item Number(s): LOSB0021 operate the equipment.
  • Page 20 7/19/10 2 degrees OUT 30mm -1 degree Stock/20 degrees 1.8mm 4 holes @ 1mm/30 wt Inside Black/Medium Center Outside 86mm Center to Center Long Down Position 2 Position 2 / Center Grease Use 1.6mm Sway Bar for more steering 1000mAh Grease 3 degrees 2 degrees...

Table of Contents