1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Measuring Instruments
  5. PR 25
  6. Operating instructions manual

Hilti PR 25 Operating Instructions Manual

Hide thumbs Also See for PR 25:
Table of Contents

Advertisement

Quick Links

PR 25
Bedienungsanleitung
Operating instructions
de
en

Advertisement

Table of Contents
loading

Related Manuals for Hilti PR 25

Summary of Contents for Hilti PR 25

  • Page 1 PR 25 Bedienungsanleitung Operating instructions...
  • Page 3 20 m 20 m 180˚...

  • Page 4: Table Of Contents

    1. General information pages. Keep these pages open when studying the oper- ating instructions. 2. Description In these operating instructions, the PR 25 rotating laser 3. Accessories is referred to as “ the tool ”. 4. Technical data 5. Safety precautions Location of identification data on the tool 6.

  • Page 5: Description

    Inclination can be set up in alignment with given marks Automatic leveling (within ±5° inclination): The tool lev- by pressing the X- and Y-keys on the PRA 25 or PR 25. els itself automatically after switching on. The laser beam is emitted only when the specified accuracy has been 2.3.3 Automatic cut-out...

  • Page 6: Accessories

    Many tasks can be carried out much more efficiently – PUA 80 charger and PRA 801 battery when the appropriate accessories for the PR 25 are used. – PA 375 and PA 377 tripod, sight rail and facade adap- The following accessories are available: tors –...

  • Page 7: Safety Precautions

    Use the tool only within its specified limits. each of the sections of these operating instructions, the Check that your PR 25 is being controlled by your following points must be strictly observed at all times. PRA 25 and that it is not reacting to commands from any other PRA 25 in use on the construction site.
  • Page 8 1:2003 Check the tool before use. If the tool is found to be damaged, have it repaired at a Hilti service center. The accuracy of the tool must be checked after it has been dropped or subjected to other mechanical stress.

  • Page 9: Before Use

    6. Before use Batteries – Do not use damaged batteries. – Do not mix old and new batteries. Do not mix batter- ies of different types or batteries from various manu- -NOTE- facturers. – The tool may be powered only by the PRA 801 recharge- able battery or by batteries manufactured in accordance 6.1 Switching on the tool with the IEC standard.

  • Page 10: Operation

    PRA 25. The laser line or laser spot can be moved to the left or – As long as the PR 25 is not in line laser mode, it then right by pressing the direction keys (PR 25 or PRA 25).
  • Page 11 A basic prerequisite for manual alignment is that the been aligned is then indicated in the display. PR 25 is set up accurately. The PR 25 must be set up so that the correct axis (X or Y) is positioned in the direc- 7.2.8 Monitoring...
  • Page 12 LEDs to blink. 7.2.9 Pairing It is possible to configure the PR 25 and the PRA 25 as 7.2.10 Working with the target plate a pair. When the two devices are paired, the rotating laser The target plate improves visibility of the laser beam.

  • Page 13: Care And Maintenance

    8. Hilti calibration service We recommend that the tool is checked by the Hilti cal- 8.1 Accuracy ibration service at regular intervals in order to verify its The accuracy of the tool in the X- or Y-directions can be reliability in accordance with standards and legal require- checked as described below.

  • Page 14: Disposal

    Most of the materials from which Hilti tools or appliances are manufactured can be recycled. The materials must be properly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old tools and appliances for recycling.

  • Page 15: Fcc Statement

    Hilti= registered trademark of the Hilti Corporation, Schaan, Liechtenstein Changes or modifications not expressly approved by Hilti could restrict the user's right to operate the equip- LASER RADIATION - DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH ment.
  • Page 16 13. EC conformity Designation: Rotating laser Type: PR 25/PR 25 IF Year of design: 2004 In conformance with CE We declare, on our own responsibility, that this product complies with the following directives and standards: EN 300 440-2, EN 301 489-3 V1.4.1,...
  • Page 17 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3049 1004 10-Pos. 1 1 Printed in Liechtenstein © 2004 Right of technical and programme changes reserved S. E. & O.

Table of Contents