Sherwood CDC-5506 Operating Instructions Manual
5 disc cd changer
Hide thumbs
Also See for CDC-5506:
- Operating instructions manual (21 pages) ,
- Operating instructions manual (18 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sherwood CDC-5506
Summary of Contents for Sherwood CDC-5506
- Page 1 OPERATING INSTRUCTIONS CDC-5506 5 DISC CD CHANGER MCM Electronics Item #50-6322...
-
Page 2: Read This Before Operating Your Unit
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 12. Use only with the cart, stand, tripod, bracket, or table 2. Keep these instructions. specified by the manufacturer, or sold with the 3. Heed all warnings. apparatus. 4. Follow all instructions. When a cart is used, use caution when moving the 5. -
Page 3: Introduction
Be sure to leave a space around this unit equal to, or greater than, shown below. Left, right and rear sides : 20 cm, top side : 40 cm. DISC SKIP OPEN / CLOSE 5 DISC CD CHANGER CDC-5506 DISC SELECTOR 5 DISC AUTOMATIC LOADING SYSTEM POWER PHONES... -
Page 4: Table Of Contents
CONTENTS Introduction • READ THIS BEFORE OPERATING YOUR UNIT Rear Panel Connections Front Panel & Remote Controls • REMOTE CONTROL OPERATION RANGE • LOADING BATTERIES Preliminary Knowledge About Discs & Files • PLAYABLE DISCS • USB MEMORY DEVICES • PLAYABLE AUDIO FILE FORMATS •... -
Page 5: Rear Panel Connections
Amplifier/receiver CD IN CONNECTING DIGILINK • Connect this jack to the DIGILINK jack of Sherwood system amplifier/receiver to control this unit remotely by DIGILINK II Sherwood amplifier/receiver DIGI LINK or III system. (For details, refer to the operating instructions of DIGILINK Sherwood amplifier/receiver.) -
Page 6: Front Panel & Remote Controls
Front Panel & Remote Controls Front panel controls DISC SKIP OPEN / CLOSE CDC - 5506 5 DISC CD CHANGER DISC SELECTOR 5 DISC AUTOMATIC LOADING SYSTEM PHONES POWER PROGRAM INTRO RANDOM ON/ STANDBY 500mA CD/ USB TIME DIMMER REPEAT 20 16 18 19 17 13 14 10 11 12 Remote controls... - Page 7 ⓑ Press this button to interrupt play temporarily. ■DIGILINK SYSTEM REMOTE CONTROL 10. STOP ( ) button This unit can be remotely conrolled with Sherwood Press this button to stop play or clear the programmed DIGILINK III amplifier or receiver. tracks/files.
- Page 8 ■USB CONNECTOR • An USB memory device can be connected to th USB connector to listen to MP3 or WMA files stored on it through this unit. ■ Note : • After USB playback, remove the USB memory device in the stop mode or in the standby mode.
-
Page 9: Remote Control Operation Range I
REMOTE CONTROL OPERATION RANGE DISC SKIP OPEN / CLOSE CDC-5506 5 DISC CD CHANGER DISC SELECTOR 5 DISC AUTOMATIC LOADING SYSTEM POWER PHONES PROGRAM INTRO RANDOM ON/ STANDBY CD/ USB TIME DIMMER REPEAT 500mA • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. -
Page 10: Preliminary Knowledge About Discs & Files
• Bit rate : 32 ~ 320 kbps • Extension : .mp3, .MP3 • Fixed bit-rate files are recommended. Variable bit-rate DISC SKIP OPEN / CLOSE CDC-5506 5 DISC CD CHANGER DISC SELECTOR (VBR) fiels are playable, but playing time may be 5 DISC AUTOMATIC LOADING SYSTEM displayed incorrectly. -
Page 11: Operations
Operations PLAYING TRACKS/FILES Before operation Depending on the selected playback source, • Push the POWER switch. load the disc(s) or connect the USB memory device. OPEN / CLOSE • Then this switch is kept depressed, it enters the standby mode. •... -
Page 12: Changing Discs During Play
Selecting a disc Start play. • Press the corresponding button to start play from the desired disc. Example : When selecting the disc 4 within 2 sec. • “ ” indicator lights up. • The unit plays from the first track/file (on the current disc to the last on the 5th disc. -
Page 13: Playing In Random Order
REPEAT PLAY Selecting a folder during play • You can play a track/file, a folder, all tracks/files or a To select previous specific passage repeatedly. Repeating a track/file, a folder, all tracks/files • During play of the desired track/file or folder, To select next •... -
Page 14: Playing The First 10 Seconds Of Each Track/File I
PLAYING IN DESIRED ORDER Repeating a specific passage • Up to 32 tracks/files can be programmed to be played in During play at the beginning of the desired any desired order. passage, press the REPEAT A↔B button. In the stop mode, enter the program mode. PROGRAM •... - Page 15 ■To clear all programmed tracks/files Repeat the above step 2 until the desired tracks • Press the STOP( ) button for more than 4 seconds in /files are programmed. the program mode. • Opening the disc tray or selecting the other playback source clears all programmed tracks/files, too.
-
Page 16: Selecting A Time Display (Audio Cd Only) I
ADJUSTING THE BRIGHTNESS OF THE While displaying the track(/file) to be replaced FLUORESCENT DISPLAY with new one, select track(/file) 10 and store it in the memory. DIMMER PROGRAM • Each time this button is pressed, the brightness of the fluorescent display changes as follows. →... -
Page 17: Troubleshooting Guide
Troubleshooting Guide If a fault occurs, run through the table below before taking your unit for repair. If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your dealer. -
Page 18: Specifications
Specifications ■ TYPICAL AUDIO PERFORMANCES • Number of channels • Frequency response, 20~20,000 Hz ±0.8 dB • Signal to noise ratio, A Wtd. 94 dB • Dynamic Range 86 dB • Total harmonic distortion, 1 kHz 0.009 % • Wow and flutter Quartz crystal precision •... - Page 19 CDC-5506 5 DISC CD CHANGER MCM Electronics Item #50-6322 5707-00000-588-0S...
Need help?
Do you have a question about the CDC-5506 and is the answer not in the manual?
Questions and answers