Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sagitter HYP006WW
Summary of Contents for Sagitter HYP006WW
- Page 1 LE D WAS H LIGHT( C+W) USER MANUAL...
-
Page 2: Before You Begin
1.BEFORE YOU BEGIN What is included Ø 1 x Fixture Ø 1 x Power cable with plug Ø 1 x User Manua Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton; check the contents to ensure that all parts are present, and have been received in good condition. -
Page 3: Safety Instructions
Safety Instructions WARNING! Please read these instructions carefully, which includes important information about the installation, usage and maintenance of this product.. The following symbols are used to identify important safety information on the product and in this manual: DANGER! DANGER! WARNING! WARNING! WARNING! -
Page 4: Specifications
2.INTRODUCTION Specifications l Voltage Rating: AC100V 240V 50-60Hz l Power Rating: 90W l LED Quantity: 36 psc LEDs(18cool white+18 warmwhite) l LED: 670mA l Beam Angle: 20°/30° /40°(option) l Ingress Protection: IP65 /indoor(option) l Product Size: 255 x 205 x290mm l Package Size: 315x280x345 mm l N/W:4.0Kg Features... -
Page 5: Product Overview
Product Overview Safety Power in Power out DMX IN DMX OUT Control board Dimensions Hanging bracket/ floor stand Bracket adjustment knob... -
Page 6: Installation Requirement
3.SETUP Installation Requirement l This product can be used in a variety of situations, can hang and put on the ground. l If hanging the fixture for over head use, then please follow the below steps. l Please choose the suitable location to put or hang the light when installing it. You must use the exclusive clamp hanger and screw when hanging it, and make sure the weight of the light is within limits of the hanger. - Page 7 Connection of DMX Signal Wire Please use the fixture controller wire specially when use the DMX512 Controller. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the first fixture. Connect the end of the cable coming from the first fixture which will have a (male) 3 pin connector to the input connector of the next fixture consisting of a (female) 3 pin connector.
-
Page 8: Operating Instructions
4.OPERATING INSTRUCTIONS Menu Map MAIN SUB- FUNCTION SELECTION INSTRUCTION FUNCTION 000~255 User can combine Cool White, Warm White to generate a custom color (0 ~ 100%) Select strobe frequency 00~20 3 auto programs available 01~03 001~512 Set DMX start address Sets the operating mode for the fixture:to receive signal from a DMX controller (DMX) .receive signal from... -
Page 9: Control Panel Functions
Control Panel Functions BUTTON FUNCTION MODE Exits from the current menu or function Enables the currently displayed menu or sets the currently selected ENTER value in to the selected function Navigates upwards through the menu list and increases the numeric value when in a function Navigates downwards through the menu list and decreases the numeric DOWN... -
Page 10: Dmx512 Controller Mode
DMX512 Controller Mode 1 DMX operate mode setting Access control panel function by pressing MODE until is displayed. Press ENTER, press UP/DOWN buttons until the is displayed. Press ENTER, Press MODE return to MENU 2 Setting DMX512 Address Ü 001--512 Access control panel function by pressing MODE until is displayed. -
Page 11: Dmx512 Channel Values
03 channels Channel Value Description 1 Dimming 000~255 0-100% 2 cool white 000~255 0-100% 3 warm white 000~255 0-100% NOTE:Channels 2, 3 control the intensity ratio of each of the Cool & Warm White LEDs. color Channels 1&2 &3 can be combined together to create multiple white CT combinations DMX512 Channel Values 07 channels... -
Page 12: Id Address Selection
ID ADDRESS SELECTION VALUE FUNCTION VALUE FUNCTION VALUE FUNCTION 000~009 All Ids ID23 ID46 010~019 ID24 ID47 020~029 ID25 ID48 030~039 ID26 ID49 040~049 ID27 ID50 050~059 ID28 ID51 060~069 ID29 ID52 070~079 ID30 ID53 080~089 ID31 ID54 090~099 ID32 ID55 100~109 ID10... -
Page 13: Master Dimmer
MASTER DIMMER Channels 1 controls the intensity of the currently projected color When the slider is at the highest position (255), then the intensity of the output is at themaximum. COOL WHITE AND WARM WHITE SELECTION Channels 2, 3 control the intensity ratio of each of the Cool & Warm White LEDs. Channels 1&2 &3 can be combined together to create multiple white CT color combinations WHITE CT MACROS Channel 4 selects the required White CT Macro. -
Page 14: Master/Slave Control Mode
Select 07channel on fixture's control panel (Please refer to DMX512 Channels Selection). The figure above shows a simple DMX layout which has used three units at each DMX address. The three units have different ID addresses. In the DMX address: 001, the user can control the first three lights simultaneously. - Page 15 5. APPENDIX Service Maintenance Guide Symptom(s) Possible Solution(s) Clean the fixture regularly to avoid any such failure. This fixture is convection cooled, which means that if the surface is kept clean and free of debris, then proper cooling will be allowed to occur 1 or more LED's are An LED may have failed, resulting in an open circuit.
-
Page 16: Blow-Out Diagram
Blow-out Diagram. Description Part Number Glass cover 6P00605 LED Lens assembly 4170705 LED Metal-core PCB assembly 2P00603 Electronic Transformer 5080102 LED Driver PCB (Master) 2P00604 Display PCB 2P00605 Display Clear plastic cover 803004 Display watertight seal 6P00613 house 6P00606 power socket 5050101 DMX socket 5040201...