BUSCH Mink MM 1324 AV Installation And Operating Instructions Manual
Vacuum pumps
Hide thumbs
Also See for Mink MM 1324 AV:
- Instruction manual (28 pages) ,
- Installation and operating instructions manual (56 pages) ,
- Instruction manual (40 pages)
Related Manuals for BUSCH Mink MM 1324 AV
Summary of Contents for BUSCH Mink MM 1324 AV
-
Page 1: Operating Instructions
Installation and Operating Instructions Vacuum Pumps Mink MM 1324, 1202, 1252, 1322, 1200, 1250, 1320 AV Busch Produktions GmbH Schauinslandstr. 1 79689 Maulburg Germany 0870133276 / 070328 / Modifications reserved... -
Page 2: Table Of Contents
Technical Data......19 Busch – All over the World in Industry ....20... -
Page 3: Product Description
Condensable Vapours). Conveyance of other vapours shall be der, on the other hand the gaps are small enough to keep the clear- agreed upon with Busch. Conveyance of water or other liquids in ance loss between the chambers low. liquid phase increases the power consumption and shall therefore In order to avoid the suction of solids, the vacuum pump is equipped be avoided (risk of drive overload). -
Page 4: Cooling
If anything remains to be damaged, e.g. bent eyebolt with a new one) clarified please contact your Busch representative! ● Make sure that the eyebolt (a) is fully screwed in and tightened by Safety Notes... -
Page 5: Conservation
However, peratures of more than 70 °C. VCI-products may attack the surfaces of plastics and elastomers. Seek advice from your local packaging dealer! Busch uses CORTEC Risk of burns! VCI 126 R film for the overseas packaging of large equipment. -
Page 6: Gas Discharge
● Mount the NEMA-adaptor flange (I) on the motor (the bolts (II) Gas Discharge are not part of the Busch scope of delivery) The discharged air must flow unobstructedly. It is not permitted to ● Undo the cylinder screws (VI) and remove the elastomer part (V) -
Page 7: Connecting Lines/Pipes
(Ú page 8: Conveying Condensable Vapours). Conveyance of other vapours shall be CAUTION agreed upon with Busch. Conveyance of water or other liquids in liquid phase increases the power consumption and shall therefore Operation in the wrong direction of rotation can destroy the be avoided (risk of drive overload). -
Page 8: Conveying Condensable Vapours
If the level does fall, the gear is leaky and the vacuum ◆ Operate the vacuum pump for another approx. 10 minutes pump requires repair (Busch service). Every 6 Months: ◆ Close the ambient air valve ●... -
Page 9: Every Year
● Make sure that the vacuum pump is shut down and locked against www.busch-vacuum.com). inadvertent start up Busch service will only accept vacuum pumps that come with a com- pletely filled in and legally binding signed “Declaration of Contamina- tion” (form downloadable from www.busch-vacuum.com). -
Page 10: Troubleshooting
(n, 714) as required and reas- semble Internal parts are worn or damaged Repair the vacuum pump (Busch service) The gas conveyed by the vacuum pump smells Process components evaporating under vac- Check the process, if applicable... - Page 11 (the proper function of the fan wheel requires the precise adjustment of the coupling on the motor shaft and on the pump shaft; therefore the motor can be mounted by the Busch ser- vice only) The vacuum pump is blocked...
-
Page 12: Sectional Drawing
Mains frequency or voltage outside tolerance Provide a more stable power supply range Partial clogging of filters or screens Remove the clogging Partial clogging in the suction, discharge or pressure line Long suction, discharge or pressure line with Use larger diameter too small diameter Sectional Drawing Sectional Drawing... -
Page 13: Spare Parts
0-9-414 7782 Fax: 0-9-414 7783 Find the list of Busch companies all over the world (by the time of the publication of these installation and operating instructions) on Ú page 16 (rear cover page). Find the up-to-date list of Busch companies and agencies all over the world on the internet at www.busch-vacuum.com. -
Page 14: Ec-Declaration Of Conformity
Note: This Declaration of Conformity and the -mark affixed to the nameplate are valid for the vacuum pump within the Busch-scope of delivery. When this vacuum pump is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process acc. -
Page 15: Technical Data
Technical Data For motor connection parameters see nameplate Type 1500 ~225 MM 1324 AV 200* 1800 ~233 3000 ~234 MM 1202 AV 3600 ~236 100* 3000 ~238 MM 1252 AV 3600 ~238 3000 ~240 MM 1322 AV 150* 3600 ~242 max. -
Page 16: Busch - All Over The World In Industry
Busch – All over the World in Industry www.busch-vacuum.com Australia New Zealand Dr.-Ing. K. Busch GmbH Niederlassung West Busch Australia Pty. Ltd. Busch New Zealand Ltd. Nordring 35 30 Lakeside Drive Unit D, Arrenway Drive 64807 Dieburg Broadmeadows, Vic. 3047...