Product Specifications; Parts And Features - Airstream A-HB-25150 Operator's Manual

Product Specifications

• Save all instructions
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 cc, 2 cycle
Idle Speed . . . . . . . . . . . . . . . . . . . . . . . 3,500-4,000 RPM
Peak Air Velocity. . . . . . . . . . . . . . . . . . . . . . . . . . . 150 mph
Air Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 CFM
Fuel Tank Capacity. . . . . . . . . . . . . . . . . . . . 20 oz (600 ml)
Fuel Type . . . . . . . Unleaded Gasoline – 87 Octane or higher
2-Cycle Oil Type . . . . . . . . 2-Cycle Oil that meets or exceeds
. . . . . . . . . . . . . . . . . . . . . . . . . . . JASO – FC Specifications
Parts & Features
Fig. 1
1
13
2
6
4
10
9
7
11
Assembly
Parts Included With The Packaged Blower
• Upper Tube (1)
• Nozzle Tube (1)
• Screw (1)
WARNING
Do not operate Blower if it is damaged or not securely and fully assembled.
Questions? Call Toll Free at 1-800-737-2112
Fuel Mixture . . . . . . . . . . . . . . . . 40:1 (Gasoline: 2-Cycle Oil)
Sound Pressure Values . . . . . . . . . . . . . . . . . . . . . . . . 79dB
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . Torch L8RTC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CHAMPION - CJ7Y
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or equivalent
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 lbs (5.2 kg)
5
9
8
3
1. Ignition Switch 8. Spark Plug
2. Handle 9. Fuel Primer Bulb
12
3. Engine 10. Choke
4. Upper Tube 11. Fuel Cap
5. Nozzle Tube 12. Air Filter Cover
6. Recoil Starter Handle 13. Throttle Lever
7. Fuel Tank
If you need assistance or find any parts missing,
CALL TOLL FREE: 1-800-737-2112
• Screwdriver with Spark Plug Wrench
• 40:1 2-Cycle Engine Oil (3.2 fl. oz.)
• Operator's Manual
4 Copyright © 2008 MAT Engine Technologies, LLC
Assembly
• Save all instructions
Blower Assembly
WARNING
Blower tube installation affects both Blower balance and
performance. The tube and nozzle must be installed
NGK - BPMR7A
correctly.
Never use the Blower without the upper tube and the
nozzles correctly fitted to the Blower.
WARNING
Rotating impeller blades can cause sever injury! Stop the
engine before installing or removing the Blower tubes.
Never perform any maintenance or assembly procedures
on this Blower while the engine is running.
1. Align the arrow on the upper tube with the arrow on the
nozzle tube. (Fig. 2 ).
2. Slide the nozzle tube to the upper tube.
3. Turn the nozzle tube clockwise until a click is reached to
secure the nozzle tube to the upper tube. (Fig. 3)
4. Align the arrow on the upper tube with the arrow on the
Blower outlet. (Fig.4)
5. Slide the upper tube to the Blower outlet.
6. Turn the upper tube clockwise until a click is reached to
secure the upper tube to the Blower outlet. (Fig.5)
Note: Position tube so that engraved writing "This Side
Up" is in an upward position. (Fig. 6)
7. Tighten the screw, until the tube is secure. (Fig.7)
Questions? Call Toll Free at 1-800-737-2112
(Continued)
Fig. 2
Fig. 3
5
Fig. 4
( THIS SIDE UP )
Fig. 5 Fig. 6
Fig. 7
Copyright © 2008 MAT Engine Technologies, LLC