Table of Contents
Advertisement
Carton Contents
Accessory Sheet
Hardware Pack
AA Battery (4) (IP only)
Junction Box Cover
Logs
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death or
property damage.
— Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any appliance.
•
Do not touch any electrical switch; do
not use any phone in your building.
•
Leave the building immediately.
•
Immediately call your gas supplier
from a neighbor's phone. Follow the
gas supplier's instructions.
•
If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be per-
formed by a qualified installer, service
agency or the gas supplier.
WARNING
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.
Note: Barrier required, but may be sold separately.
INSTALLATION INSTRUCTIONS
AND OWNER'S MANUAL
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Rockwool
Registration Card
Power Adaptor (IP only)
Receptical
Decorative Rocks
WARNING
HOT GLASS
CAUSE BURNS.
DO NOT TOUCH
UNTIL COOLED.
NEVER
ALLOW CHILDREN
TO TOUCH GLASS.
DIRECT VENT ZERO CLEARANCE GAS
FIREPLACE HEATER SERIES:
DVD(32,36,42,48)FP3(0,1,2,3)(N,P)-2
DVD(32,36,42)FP35(N,P)-1
DVD(32,36,42,48)FP5(0,1,2,3)N-3
INTERMITTENT PILOT (IP)
DVD(32,36,42,48)FP7(0,1)(N,P)-1
UL FILE NO. MH30033
WARNING: If not installed, operated and maintained
in accordance with the manufacturer's instructions,
this product could expose you to substances in fuel
or from fuel combustion which can cause death or
serious illness.
This appliance may be installed in an
a f t e r m a r k e t , p e r m a n e n t l y l o c a t e d ,
manufactured home (USA only) or mobile
home, where not prohibited by state or local
codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with other
gases, unless a certified kit is used.
WILL
GLASS
MILLIVOLT (MV)
DIRECT IGNITION (DI)
GAS-FIRED
Page 1
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Empire DVD32FP30N-2
Summary of Contents for Empire DVD32FP30N-2
-
Page 1: Installation Instructions
INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL GAS-FIRED INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. DIRECT VENT ZERO CLEARANCE GAS Carton Contents FIREPLACE HEATER SERIES: Accessory Sheet Rockwool Hardware Pack Registration Card MILLIVOLT (MV) AA Battery (4) (IP only) Power Adaptor (IP only) Junction Box Cover Receptical... -
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION PAGE IMPORTANT SAFETY INFORMATION ............................3 SAFETY INFORMATION FOR USERS OF LP GAS ........................4 REQUIREMENTS FOR MASSACHUSETTS ........................... 5 INTRODUCTION ....................................6 SPECIFICATIONS .................................... 7 VENT SYSTEM IDENTIFICATION ..............................8 SPECIAL VENT SYSTEMS ................................8 FIREPLACE DIMENSIONS ................................ -
Page 3: Important Safety Information
• Installation and repair should be done by a glass frame assembly from Empire. See parts list QUALIFIED SERVICE PERSON. The appliance on Pages 56 - 63 for ordering. should be inspected before use and at least annually by a qualified service person. -
Page 4: Safety Information For Users Of Lp Gas
SAFETY INFORMATION FOR USERS OF LP GAS Propane (LP-Gas) is a flammable gas which can cause its odor intensity. fires and explosions. In its natural state, propane is odor- LP-Gas may stratify in a closed area, and the odor intensity less and colorless. -
Page 5: Requirements For Massachusetts
REQUIREMENTS FOR MASSACHUSETTS For all side wall horizontally vented gas fueled equipment installed SIGNAGE. A metal or plastic identification plate shall be in every dwelling, building or structure used in whole or in part for permanently mounted to the exterior of the building at a residential purposes, including those owned or operated by the minimum height of eight feet above grade directly in line with Commonwealth and where the side wall exhaust vent termination... -
Page 6: Introduction
• Modification of the fireplace or direct vent system. means any individual, firm, corporation or company which either in • Installation other than as instructed by Empire Comfort Systems, Inc. person or through a representative is engaged in and is responsible for •... -
Page 7: Specifications
SPECIFICATIONS DVD32 DVD36 DVD42 DVD48 Input BTU/Hr Maximum 18000 (NAT, LP) 20,000 (NAT, LP) 25,000 (NAT, LP) 28,000 (NAT, LP) 14,000 (NAT) 18,000 (NAT) 20,000 (NAT) Input BTU/Hr Minimum (millivolt only) 14,000 (NAT, LP) 16,500 (LP) 19,500 (LP) 22,000 (LP) KWH (Maximum) KWH (Minimum) Orifice NAT... -
Page 8: Vent System Identification
300°F/149°C. The inner flue joints do not require any sealant. Special Venting Components (Simpson Duravent) See Empire Comfort Systems Retail Price List for Simpson Duravent part numbers and pricing. Special DV Vent Kits Available from Empire Comfort Systems, Inc. -
Page 9: Fireplace Dimensions
FIREPLACE DIMENSIONS DVD32 DVD36 DVD42 DVD48 34" 37" 43" 49" 864 mm 940 mm 1092 mm 1245 mm 31" 34" 40" 46" 787 mm 864 mm 1016 mm 1168 mm 23 1/16" 23 1/16" 25 1/16" 25 1/16" 585 mm 585 mm 636 mm 636 mm... -
Page 10: Clearances
The flow of heat can ignite combustibles. Note: When using Empire EMBF, UMC, and UMF Series Full Mantels with DVD32 and DVD36 Series Fireplaces, combustible clearance may be reduced to 1” clearance from top edge of fireplace face. -
Page 11: Locating Fireplace
LOCATING FIREPLACE Note: Island and Room Divider installation is possible as long as the horizontal portion of the vent system does not exceed 20 feet with a minimum vertical run of 8 feet. See details in Venting Section. When you install your Direct Vent Fireplace in Room divider or Flat on wall corner positions, a minimum of six inches clearance must be maintained from the perpendicular wall and the front edge of the appliance. -
Page 12: Gas Supply
GAS SUPPLY The gas pipeline can be brought in through the right or left side of Installing a New Main Gas Cock the appliance. Consult the current National Fuel Gas Code, ANSI Each appliance should have its own manual gas cock. Z223.1 CAN/CGA-B149 (.1 or .2) installation code. -
Page 13: Installation
INSTALLATION Framing and Finishing Vent Pipe Clearance Note: Maintain one inch of clearance around vertical vent pipe. See Choose unit location. Frame in fireplace with a header across the top. It is important Figure 11. For horizontal vent, maintain a minimum 1” clearance to to allow for finished face when setting the depth of the frame. - Page 14 INSTALLATION (continued) Note: For finishing to top of fireplace, refer to Figure 14. Flush Mount Mantel Installation The fireplace must extend 3/4" beyond finished wall surface when using a flush mount mantel. Refer to Figure 13 to locate nailing flanges on fireplace sides. Mark and drill two 1/8" holes into fireplace side to mount each nailing flange.
- Page 15 INSTALLATION (continued) Flush Wall Installation Attention: Cold climate installation recommendation: When installing this unit against a non-insulated exterior wall, it is recommended that the outer walls be insulated to conform to applicable insulation codes. Vent Runs In planning the installation for the fireplace, it is necessary to install certain components before the appliance is completely positioned and installed.
- Page 16 INSTALLATION (continued) HORIZONTAL ONLY, STRAIGHT OUT THE BACK "A" "B" Models 5 1/8" to 6 1/2" 6" DVD 32,36,42,48 (130 mm to 165 mm) 8 1/8" to 9 1/2" 9" DVD 32,36,42 (206 mm to 241 mm) 11 1/8" to 12 1/2" 12"...
- Page 17 INSTALLATION (continued) CORNER INSTALLATION VERTICAL, 90° ELBOW TO HORIZONTAL OUT THE WALL Dim. DVD32 DVD36 DVD42 DVD48 36 1/8" 38 3/8" 42 1/2" 46 3/4" 918 mm 975 mm 1080 mm 1187 mm 25 1/2" 27 1/8" 30 1/8" 33 1/8" 648 mm 689 mm 765 mm...
-
Page 18: Venting Fireplace - Top
VENTING FIREPLACE - TOP To Use the Vent Graph Venting Graph (Dimensions in Feet) 1. Determine the height of the center of the horizontal vent pipe. Using this dimension on the Sidewall Vent Graph, locate the point it intersects with the slanted graph line. 2. - Page 19 VENTING FIREPLACE - TOP (continued) Below Grade Installation When it is not possible to meet the required vent terminal clearances of 12” (305 mm) above grade level, a snorkel kit is recommended. It allows installation depth down to 7” (178 mm) below grade level. The 7”...
-
Page 20: Venting Fireplace - Top
VENTING FIREPLACE - TOP (continued) Cutting the Hole After the fireplace has been positioned in its permanent location, the hole through the exterior wall of the house can be cut. This hole must be 11" (280mm) high x 10" (254mm) wide with its center line determined by the amount of vertical rise and horizontal run of the termination. -
Page 21: Examples - Top Vent Run
EXAMPLES - TOP VENT RUN Figure 30 Figure 29 Figure 31 31629-13-1215 Page 21... -
Page 22: Venting Fireplace - Rear
VENTING FIREPLACE - REAR Venting Graph (Dimensions in Feet) To Use the Vent Graph 1. Determine the height of the center of the horizontal vent pipe. Using this dimension on the Sidewall Vent Graph, locate the point it intersects with the slanted graph line. -
Page 23: Examples - Rear Vent Run
EXAMPLES - REAR VENT RUN Model Maximum Pipe Length H1 DVD32 24" DVD36 24" DVD42 24" DVD48 6" Figure 35 Figure 33 Model Maximum Pipe Length H1 DVD32 24" DVD36 24" DVD42 18" DVD48 Figure 36 Figure 34 31629-13-1215 Page 23... -
Page 24: Rear Vent Conversion
REAR VENT CONVERSION Converting flue take-off to rear venting When switching out the flue and inlet vent collars to run horizontally 4. Reinstall the inlet cover plate over the top inlet opening with 4 off the rear vent, the following steps must be taken. screws. -
Page 25: Vent Clearances
VENT CLEARANCES Figure 37 *Clearance above grade, veranda, porch, deck or balcony clearance to non-mechanical air supply inlet to building or [*12 inches (305 mm) minimum] the combustion air inlet to any other appliance [*12 inches (305 mm) minimum for appliances ≤ 100,000 BTU/Hr (30 clearance to window or door that may be opened [*12 inches (305 mm) minimum for appliances <... -
Page 26: Framing And Finishing
FRAMING AND FINISHING Installing Support Brackets A horizontal pipe support MUST BE used for each 3 feet of horizontal run. The pipe supports should be placed around the pipe and nailed in place to framing members. There MUST BE a 3 inch clearance to combustibles above 6 5/8 inch diameter pipe and elbows and 1 inch clearance on both sides and bottom of 6 5/8 inch pipe to combustibles on all horizontal pipe sections and elbows. -
Page 27: Framing And Finishing
FRAMING AND FINISHING (continued) Vertical Firestops Vertical runs of this system which pass through ceilings require the use of ONE ceiling firestop at the hole in each ceiling through which the vent passes. Position a plumb bob directly over the center of the vertical vent component and mark the ceiling to establish the center point of the vent. -
Page 28: Termination Clearances
TERMINATION CLEARANCES Termination clearance for buildings with combustible and noncombustible exteriors. Figure 43 Vertical Sidewall Installations Important! Minimum clearance between vent pipes and combustible materials is three inches (76 mm) on top, and one inch (25 mm) on bottom and sides. Important! When vent termination exits through foundation less than 20"... -
Page 29: Horizontal Termination
HORIZONTAL TERMINATION NOTE: Termination cap should pass through the wall firestop from For installations requiring a vertical rise on the exterior of the the exterior of the building. Adjust the termination cap to building, 14-inch and 36-inch tall Snorkel Terminations, as shown in its final exterior position on the building. -
Page 30: Vertical Termination
VERTICAL TERMINATION out at joints. Condensate can cause corrosion of caps, pipe and Locate and mark the center point of the vent pipe using a nail on fittings. It may be caused by having excessive lateral runs, too the underside of the roof. Drive the nail through the center point. many elbows and exterior portions of the system being exposed Mark the outline of the roof hole around this center point. -
Page 31: Vertical Termination
Vertical Inlet baffle, DVF-139 combustion chamber must be examined by a qualified service person from your Empire Comfort Systems, Inc. distributor or dealer for for damage. All damaged gaskets on the glass frame assembly and Simpson Duravent only. -
Page 32: Dvvk-4F Flex Vent Instructions
DVVK-4F FLEX VENT INSTRUCTIONS The DVVK-4F FLEX VENT KIT includes the following compo- Install the Wall Firestop/Thimble assembly as required through the wall. Refer to the venting charts in the fireplace manual to determine nents: the proper height and size of the vent opening. The minimum opening •... -
Page 33: Dvvk-4Re Vent Kit Installation Instructions
NOTE: If installing onto wood, lap, or vinyl siding, the vinyl siding kit should be used (sold separately, part number DV-822). The vinyl siding vent kit, DV-822, is available from Empire Comfort Systems, Inc. The depth is 3” (76 mm), which enables the vent Figure 50 cap to be extended away from vinyl siding or projections. - Page 34 DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS (continued) 7. Remove outside mounting plate with tube attached from wall. Mark and cut the extra length of the 6 5/8” (168 mm) diameter tube from the opposite end. Do not crimp or enlarge tube. 8.
- Page 35 DVVK-4RE VENT KIT INSTALLATION INSTRUCTIONS (continued) Follow correct option according to venting method. Connecting to Rigid Vent System If the air inlet and flue outlet tubes are to be connected to a rigid Connecting Directly to Fireplace venting system (and not directly to the back of the unit), then do If the air inlet and flue outlet tubes are to be connected directly to not use the gasket provided.
-
Page 36: Log Placement (5 Log Set) - Dvd(32,36)Fp
LOG PLACEMENT (5 LOG SET) - DVD(32,36)FP This fireplace is supplied with a set of five ceramic fiber logs. Do not handle these logs with your bare hands! Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fibers. -
Page 37: Log Placement (7 Log Set) - Dvd(42,48)Fp
LOG PLACEMENT (7 LOG SET) - DVD(42,48)FP This fireplace is supplied with a set of seven ceramic fiber logs. Do not handle these logs with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers. After handling logs, wash your hands gently with soap and water to remove any traces of fiber. -
Page 38: Millivolt Operating Instructions (Fp3 Series)
MILLIVOLT OPERATING INSTRUCTIONS (FP3 SERIES) 750 Millivolt System The OWNER should carefully read and follow these operating The standing pilot (750 millivolt system) is a continuous burning instructions at all times. Lower the door assembly to view the gas pilot. The pilot remains ON even when the main burner is OFF. controls for the fireplace. - Page 39 MILLIVOLT OPERATING INSTRUCTIONS (FP3 SERIES) Electric (120 volt) Operated Remote Control, FREC STANDING PILOT OPERATING INSTRUCTIONS Connect the green and red, stripped and bare, wires on the REMOTE/ REMOTE/OFF/ON Switch OFF/ON switch wire harness to the wires on remote receiver that The fireplace is equipped with a REMOTE/OFF/ON switch.
-
Page 40: Millivolt Standing Pilot Wiring Diagram (Fp3 Series)
MILLIVOLT STANDING PILOT WIRING DIAGRAM (FP3 SERIES) Figure 61 Page 40 31629-13-1215... -
Page 41: Millivolt Standing Pilot Lighting Instructions (Fp3 Series)
MILLIVOLT STANDING PILOT LIGHTING INSTRUCTIONS (FP3 SERIES) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. This appliance has a pilot which must be lighted by hand. C. -
Page 42: Millivolt Standing Pilot Troubleshooting (Fp3 Series)
—If thermocouple is producing more than 15 millivolts, replace a. Flame impingement on logs. faulty valve. —Check and adjust log position. Contact Empire Comfort 3. Pilot burning, no gas to burner, valve knob “ON”, REMOTE/ Systems, Inc. OFF/ON switch “ON.”... -
Page 43: Direct Ignition Lighting Instructions (Fp5 Series)
DIRECT IGNITION LIGHTING INSTRUCTIONS (FP5 SERIES) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE. BEFORE LIGHTING smell all around the appliance area for Use only the wall switch or remote control switch to turn the gas. -
Page 44: Direct Ignition Wiring Diagram (Fp5 Series)
DIRECT IGNITION WIRING DIAGRAM (FP5 SERIES) LED CODES Steady ON Normal operation, power ON to control 2 Flashes 3 unsuccessful ignition trials 3 Flashes Main burner flame failed 4 times during a single heating cycle 4 Flashes Interrupt power for 5 seconds to reset control Steady Flash Flame detected out of sequence Figure 62... -
Page 45: Initial Start Up Gas Line Purge (Fp5 Series)
INITIAL START UP GAS LINE PURGE (FP5 SERIES) NOTE: UNIT MUST BE PROPERLY GROUNDED FOR ELECTRONIC IGNITION TO FUNCTION. On initial installation, or after extended periods where the fireplace has not been used, gas lines may require purging. The installer or qualified service person may use the following purge procedures to prevent the delays that would be caused by waiting for the lockout periods between tries for ignition. -
Page 46: Direct Ignition Propane/Lp Gas Conversion (Fp5 Series)
DIRECT IGNITION PROPANE/LP GAS CONVERSION (FP5 SERIES) The conversion shall be carried out in accordance with the 14. Replace main burner onto burner assembly. Place main requirements of the provincial authorities having jurisdiction burner beneath electrodes, slide main burner from right to and in accordance with the requirements of the CSA B149.2 left into burner location, and pivot main burner away from installation code (Canada) and with the requirements of the... -
Page 47: Propane/Lp Gas Conversion (Fp5 Series)
PROPANE/LP GAS CONVERSION (FP5 SERIES) Maxitrol Valve Conversion “A” Model AIR SHUTTER BURNER ORIFICE SETTINGS Opening "A" Propane/LP Orifice DVD32 1/4" (6.4 mm) DVD36 1/4" (6.4 mm) DVD42 5/16" (7.9 mm) 1.45 mm DVD48 5/16" (7.9 mm) 1.55 mm Figure 63 Figure 64 31629-13-1215 Page 47... -
Page 48: Ipi Electronic System Operating Instructions (Fp7 Series)
IPI ELECTRONIC SYSTEM OPERATING INSTRUCTIONS (FP7 SERIES) 5.25 VDC ELECTRONIC CONTROL VALVE OPTIONAL REMOTE CONTROLS The electronic control valve system includes the ability to switch Optional remote controls are available for use with this appliance. the pilot from a standing pilot mode to an intermittent pilot mode. It is recommended that the remote receiver be placed either in a •... -
Page 49: Ipi Electronic System Wiring Diagram (Fp7 Series)
IPI ELECTRONIC SYSTEM WIRING DIAGRAM (FP7 SERIES) If any of the original wire supplied with this unit must be replaced, it must be replaced with equivalent gauge and temperature rated wire. This appliance is only for use with the type of gas indicated on the rating plate in this appliance and may be installed in an aftermar- ket, permanently located, manufactured (mobile) home where not prohibited by local codes. -
Page 50: Intermittent Pilot Lighting Instructions (Fp7 Series)
INTERMITTENT PILOT LIGHTING INSTRUCTIONS (FP7 SERIES) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. This appliance has a pilot which can be lighted with the C. -
Page 51: Intermittent Pilot Control System Troubleshooting (Fp7 Series)
INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING (FP7 SERIES) Brief Description of the Components The gas valve is fitted with a manual HI/LO knob to allow for man- ual modulation of the gas outlet pressure to the appliance burner. The controls are designed to be used with either LPG or Natural Gas and can be converted by use of an OEM supplied conversion kit. - Page 52 INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING (FP7 SERIES) Page 52 31629-13-1215...
- Page 53 INTERMITTENT PILOT CONTROL SYSTEM TROUBLESHOOTING (FP7 SERIES) 31629-13-1215 Page 53...
-
Page 54: Maintenance And Service
MAINTENANCE AND SERVICE PLEASE NOTE WARNING: It is normal for appliances fabricated of steel to give off 1. The use of substitute glass will void all product warranties. some expansion and/or contraction noise during the start 2. Care must be taken to avoid breakage of the glass. up or cool down cycle. -
Page 55: Master Parts Distributor List
MASTER PARTS DISTRIBUTOR LIST To Order Parts Under Warranty, please contact your local Empire dealer. See the dealer locator at www.empirecomfort. com. To provide warranty service, your dealer will need your name and address, purchase date and serial number, and the nature of the problem with the unit. -
Page 56: Dvd32Fp(3,5,7) Parts List
DVD32FP(3,5,7) PARTS LIST PART NUMBER PART NUMBER INDEX INDEX DESCRIPTION DESCRIPTION (FP3) (FP5) (FP7) (FP3) (FP5) (FP7) R7654 R7654 R7654 FLUE INSULATION P212 P212 P212 ORIFICE FITTING FLUE INSULATION RE- TUBING ASSEMBLY, 17425 17425 17425 17258 23550 31570 TAINER INLET R7566 R7566 R7566... -
Page 57: Dvd32Fp(3,5,7) Parts View
DVD32FP(3,5,7) PARTS VIEW USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. 31629-13-1215 Page 57... -
Page 58: Dvd36Fp(3,5,7) Parts List
DVD36FP(3,5,7) PARTS LIST PART NUMBER PART NUMBER INDEX INDEX DESCRIPTION DESCRIPTION (FP3) (FP5) (FP7) (FP3) (FP5) (FP7) R7654 R7654 R7654 FLUE INSULATION R7572 R7572 R7572 JAMB NUT FLUE INSULATION P212 P212 P212 ORIFICE FITTING 17425 17425 17425 RETAINER TUBING ASSEMBLY, 17258 23550 31570... -
Page 59: Dvd36Fp(3,5,7) Parts View
DVD36FP(3,5,7) PARTS VIEW 31629-13-1215 Page 59... -
Page 60: Dvd42Fp(3,5,7) Parts List
DVD42FP(3,5,7) PARTS LIST PART NUMBER PART NUMBER INDEX INDEX DESCRIPTION DESCRIPTION (FP3) (FP3) (FP7) (FP3) (FP3) (FP7) R7654 R7654 R7654 FLUE INSULATION P286 P286 P286 ORIFICE (NAT) FLUE INSULATION P208 P208 P208 ORIFICE (LPG) 17425 17425 17425 RETAINER R7572 R7572 R7572 JAMB NUT R7566... -
Page 61: Dvd42Fp(3,5,7) Parts View
DVD42FP(3,5,7) PARTS VIEW 31629-13-1215 Page 61... -
Page 62: Dvd48Fp(3,5,7) Parts List
DVD48FP(3,5,7) PARTS LIST PART NUMBER PART NUMBER INDEX INDEX DESCRIPTION DESCRIPTION (FP3) (FP3) (FP7) (FP3) (FP3) (FP7) P285 P285 P285 ORIFICE (NAT) R7654 R7654 R7654 FLUE INSULATION FLUE INSULATION P258 P258 P258 ORIFICE (LPG) 17425 17425 17425 RETAINER R7572 R7572 R7572 JAMB NUT R7566... -
Page 63: Dvd48Fp(3,5,7) Parts View
DVD48FP(3,5,7) PARTS VIEW 31629-13-1215 Page 63... -
Page 64: Fbb4 Optional Variable Speed Blower Installation
FBB4 OPTIONAL VARIABLE SPEED BLOWER INSTALLATION Attention: Install blower assembly before connecting gas inlet 5. Insert blower assembly into interior, bottom of fireplace. supply line Position blower assembly behind gas valve, align notch on back of blower assembly with center screw on fireplace Note: Junction box on right side of fireplace must be pre-wired at back and push blower assembly against fireplace back. -
Page 65: Fbb4 Optional Variable Speed Blower Installation
FBB4 OPTIONAL VARIABLE SPEED BLOWER INSTALLATION R7731 BLOWER ASSEMBLY 31920 SWITCH ASSEMBLY R4192 SPEED CONTROL KNOB R4186 SPEED CONTROL 31629-13-1215 Page 65... -
Page 66: Junction Box Wiring Installation Instructions
JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS STANDARD MILLIVOLT VALVE MODELS CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY IS DISCONNECTED. -
Page 67: Accessories
ACCESSORIES The following accessory parts can be obtained from your Empire Comfort Systems dealer. If you need additional information beyond what your dealer can furnish, contact Empire Comfort Systems Inc., Nine Eighteen Freeburg Ave., Belleville, Illinois 62220-2623. Accessory Description Model Number Fan Kit This fan kit is designed to provide forced air flow. -
Page 68: Decorative Accessories
DECORATIVE ACCESSORIES Decorative Door Decorative Door Decorative Frame (with hinges) Mission Rectangle Plain Rectangle Note: Decorative Frame required for use with Empire Comfort Systems Decorative Door. Decorative Door Decorative Door Mission Arch Plain Arch Window Trim Standard Louvers 45 Degree... -
Page 69: Warranty
WARRANTY Empire Comfort Systems Inc. warranties this hearth product to be free from defects at the time of purchase and for the periods speci- fied below. Hearth products must be installed by a qualified technician and must be maintained and operated safely, in accordance with the instructions in the owner’s manual. -
Page 70: Appliance Service History
APPLIANCE SERVICE HISTORY Date Dealer Name Service Technician Name Service Performed/Notes Page 70 31629-13-1215... - Page 71 APPLIANCE SERVICE HISTORY Date Dealer Name Service Technician Name Service Performed/Notes 31629-13-1215 Page 71...
- Page 72 Empire Comfort Systems Inc. EMPIRE EMPIRE 918 Freeburg Ave. Belleville, IL 62220 If you have a general question about our products, please e-mail us at info@empirecomfort.com. If you have a service or repair question, please contact your dealer. Comfort Systems www.empirecomfort.com...