Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
956
.776
2.047
3.599
.776
.197
.591
2.382
1.594
.197
THIS DOCUMENT CONTAINS INFORMATION
PROPRIETARY AND CONFIDENTIAL TO DIGI
INTERNATIONAL INC. BY ACCEPTING
DELIVERY, RECIPIENT AGREES TO RETAIN IT
IN CONFIDENCE AND NOT DISCLOSE IT TO
OTHERS NOR USE IT FOR ANY PURPOSE
OTHER THAN THAT FOR WHICH IT WAS
DELIVERED, AND TO PROMPTLY RETURN IT
UPON REQUEST.
XPress
Ethernet
-
-
REV
ECO
UNLESS OTHERWISE SPECIFIED ALL
DIMENSIONS ARE IN INCHES...
TOLERANCES ARE AS FOLLOWS:
APPROVALS
.XX +/- .01
.XXX +/- .005
ANGLES +/- 2
ı$
THIRD ANGLE PROJECTION
DESIGNED
Bridge
DRAWN
MATERIAL
CHECKED
ENGINEER
FINISH
DO NOT SCALE DRAWING
USER'S MANUAL
-
TJE
DESCRIPTION OF CHANGE
BY
DATE
TJE
12-9-09
TITLE
TJE
12-9-09
9XPress Manual Drawing
TJE
12-9-09
SIZE
CODE ID
PART NO.
TJE
12-9-09
B
SCALE NTS
PRO/ENGINEER
TJE
TJE
12-9-09
CKD
APPR
DATE
REV
9XPress
-
SHEET 1 OF 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Digi XPress
Summary of Contents for Digi XPress
- Page 1 TITLE DRAWN 12-9-09 MATERIAL 9XPress Manual Drawing CHECKED 12-9-09 THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY AND CONFIDENTIAL TO DIGI INTERNATIONAL INC. BY ACCEPTING SIZE CODE ID PART NO. ENGINEER 12-9-09 DELIVERY, RECIPIENT AGREES TO RETAIN IT IN CONFIDENCE AND NOT DISCLOSE IT TO...
-
Page 2: Technical Specifications
User’s Manual Thank you for your purchase of the XPress Ethernet Bridge. If you have any questions when configuring your Digi system, the best place to get answers is to visit http://www.digi.com/products/wireless/xpress.jsp. You will also find the latest updates there. If more assistance is needed, send email to rf-experts@digi.com or call technical support at the number below during normal... -
Page 3: Operational Summary
Also, the SU should be placed at least 10 feet from the AP to avoid overloading the radio’s receiver. Any 10/100 BaseT Ethernet client device (ECD) can be connected to an XPress subscriber unit. Each SU encrypts Ethernet traffic received from the attached ECD and transmits the data wirelessly to its AP . -
Page 4: Physical Dimensions
.XXX +/- .00 THIRD ANGLE 900 MHz Channels MATERIAL THIS DOCUMENT CONTAINS INFORMATION PROPRIETARY AND CONFIDENTIAL TO DIGI INTERNATIONAL INC. BY ACCEPTING DELIVERY, RECIPIENT AGREES TO RETAIN IT IN CONFIDENCE AND NOT DISCLOSE IT TO FINISH OTHERS NOR USE IT FOR ANY PURPOSE... -
Page 5: Digital Setup
3. Run the IP Discovery Utility, changer_DIGI.exe and you should see a window similar to this: The XPress should appear in the list at the default IP address of 192.168.17.17. If it does not, click “Search” to regenerate the list. If it still does not appear, you have a connection issue and need to re-examine the cabling or you may have a firewall issue on your computer. - Page 6 It is important that the IP address of the XPress is in the same subnet as your computer. For example, if the subnet mask is 255.255.255.0 (a class C network), the first three number groups of the IP address must match.
- Page 7 • A graphical spectrum analyzer display that may help you to select radio channels that avoid interference • A section to be used if an update to the XPress firmware is required. Note that there are two possible firmware loads for this unit, one for compatibility with older XPress Ethernet Bridge Multipoint radios (XEB09-Bxxx), and an international version that limits the frequency band to 915-928 MHz (Channels 7 through 12).
-
Page 8: Fcc Certification
FCC Certification The XPress Ethernet Bridge complies with Part 15 of the FCC rules and regulations. Compliance with labeling requirements, FCC notices and antenna regulations is required. IMPORTANT: The XPress Ethernet Bridge has been certified by the FCC for use with other products without any further certification (as per FCC section 2.1091).
Need help?
Do you have a question about the XPress and is the answer not in the manual?
Questions and answers